Vax Rapide Spring Clean Anniversary Edition Owner's manual

Brand: Vax

Model: Rapide Spring Clean Anniversary Edition

Category: Vacuum cleaners

Type: Owner's manual

This manual is also suitable for

vax.co.uk

Please read carefully before using this cleaner.

Always fully extend the mains cable before use.

Retain for future reference.

instruction manual

Carpet washer

Vax model number:

W91-RS-B Series

W90-RS-B Series

Vax Careline: (UK) 0844 412 8455

(ROI) 1-800 928 308

Version 1.3

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 1

parts overview

Fig.1/1

vax.co.uk

1. Diagram

1 Handle

2 Clean water tank release

3 Clean water tank

4 Dirty water tank lid

5 Wheels

6 Suction channel

7 Cord hooks

8 On/off switch

9 Handle release pedal

10 Vax Carpet Cleaning Solution

CLEANING

SOLUTION

W91-RS-B/W90-RS-B

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 2

safety information

2. Safety Information

FOR HOUSEHOLD USE ONLY.

When using the carpet washer, basic safety precautions

should always be observed, including the following:

1. Do not leave the carpet washer unattended when

plugged in. Unplug it from socket when not in use.

2. To prevent electric shock do not use outdoors.

3. Not to be used as a toy. Children should be supervised to

ensure that they do not play with the appliance.

4. This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning the use of the appliance by a person

responsible for their safety.

5. Use only as described in this manual.

6. Do not use the carpet washer with a damaged cord or

plug. If the supply cord or plug is damaged, it must be

replaced by the manufacturer or a recommended

Service Agent to avoid hazard and invalidating the

guarantee.

7. Do not pull or carry by the cord, use the cord as a

handle, allow the cord to come into contact with hot

or sharp surfaces or close a door on the cord.

8. Do not unplug by pulling on the cord.

9. Do not handle the plug or carpet washer with wet

hands.

10. Do not put any objects into openings or operate with

openings blocked, keep them free of anything that

may reduce airflow.

11. Keep hair, loose clothing, fingers and all parts of the

body away from openings and moving parts.

12. Do not use the carpet washer on any glowing,

burning or smoking particles.

13. Do not use without the solution tank and dirty water

tank in place.

14. Turn off all controls before unplugging.

15. Do not use to pick up flammable or combustible

liquids such as petrol, or use in areas where they may

be present.

16. Keep the unit on the floor.

17. Do not use an extension cord.

18. Do not attempt to remove blockages with sharp

objects as they may cause damage.

19. Store indoors put away after use to prevent tripping

accidents.

20. Using improper voltage may result in damage to the

motor and possible injury to the user. The correct

voltage is listed on the rating label.

21. A hazard may occur if the carpet washer runs over

the power supply cord.

22. To prevent dirty water from running into motor, do

not hold the appliance upside-down or lay on its side.

Use appliance in normal vacuuming position.

23. Use extra care when cleaning on stairs.

24. Do not carry appliance while motor is running.

NOTE: Carpets should be dry vacuumed

thoroughly before washing.

NOTE: The unit must be unplugged from the

mains socket outlet after use, and before

cleaning or maintaining the unit.

IMPORTANT: This unit is not intended for

commercial use.

PLEASE KEEP THESE INSTRUCTIONS

FOR FURTHER USE.

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 3

vax.co.uk

assembly/ operation

3. Assembly

Putting your cleaner together

Insert middle frame to machine base (Fig 3/1).

Insert one screw on either side of middle frame to secure

(Fig 3/2).

Slide the upper handle down onto the unit. The handle

will click and lock in place. Run the mains wire above the

upper cord hook and secure with the cord clip (Fig 3/3).

Insert locking pins into either side of handle (Fig 3/4).

Screw locking pins into handle (Fig 3/5).

4. Operation

IMPORTANT: Turn off when emptying and filling

the tanks and performing any maintenance.

Grasp the solution reservoir under the handle and press

the handle release lever in (Fig 4/1).

Tilt the solution reservoir away from the cleaner and

remove (Fig 4/2).

Unscrew the cap from the back of the solution reservoir

(Fig 4/3).

Pour the correct amount of Vax Solution as directed on

the solution label into the clean water tank.

Fig.3/3

Fig.4/1

Fig.4/2

Fig.4/3

Fig.3/2

Fig.3/1

Fig.3/4 Fig.3/5

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 4

operation

IMPORTANT: Maximum water temperature

50°C.

Fill the remaining space in the solution reservoir with

warm tap water. Replace the measuring cap (Fig 4/4).

NOTE: use only Vax Solution, using other cleaning

solutions may cause excessive foaming.

This may cause the float to shut off the cleaner

prematurely. Using other cleaning solutions will

invalidate your warranty.

Place the bottom of the solution reservoir into the

cleaner and push into place. There will be an audible click

when the reservoir is in the correct position (Fig 4/5).

Plug the cord into a mains electricity socket.

Turn the power switch on (Fig 4/6).

The switch is located on the back of the cleaner, next to

the handle release.

The power switch controls the vacuum motor. Press on

the handle release pedal and pull the cleaner back into a

reclined position (Fig 4/7).

IMPORTANT: Never leave the cleaner

unattended with the power on.

NOTE: Vacuum carpets thoroughly with dry vacuum

cleaner before washing.

Whilst depressing solution spray trigger, push carpet

washer in a forwards motion. Release trigger and pull unit

backwards in same path to remove dirty water and

solution from the carpet. (Fig 4/8).

Repeat if necessary, when the dirty water reaches the

max fill line on the dirty water tank empty the tank.

Fig.4/4

Fig.4/5

Fig.4/7

Fig.4/6

Fig.4/8

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 5

vax.co.uk

operation

Emptying the dirty water tank

NOTE: The float in your Rapide is located forwards of

the back the dirty water tank lid. It will shut off the

suction when the dirty water tank is full. For best

results use a smooth steady motion keeping the

nozzle flat against the carpet.

Tipping the cleaner and breaking the seal of the

nozzle against the carpet will cause the float to rise

cutting off suction. Once the float is activated, empty

the dirty water tank. If the tank does not appear full

turn off the power switch and wait for the float to

settle. For best results use only Vax Solution.

You will hear a change in motor pitch when the tank is full

and needs emptying.

IMPORTANT: Unplug your cleaner before

emptying the dirty water tank.

Grasp the top of the dirty water tank handle and press

the release latch. Grasp the handle and pull up top of the

base, take care to ensure that no dirty water leaks from

the front (Fig 4/10).

Remove dirty water tank (Fig 4/11).

To empty the water tank grasp the handle with one hand

and nozzle with the other and empty into the sink

(Fig 4/13).

Cleaning the dirty water tank

Rinse the dirty water tank and top thoroughly, with warm

water (Fig 4/14).

You should allow them to dry fully before replacing them

on your cleaner to prevent mildew.

Do not use any chemicals in the cleaning process.

Replacing the dirty water tank

Lift the front of the carpet cleaner base off the carpet

with one hand.

Grasp the handle and hook the front of the dirty water

tank into the base, making sure that the front of the

dirty water tank is resting on the base.

Failure to install the dirty water tank correctly will result

in poor dirty water pick up (Fig 4/15).

Fig.4/11

Fig.4/14

Fig.4/15

Fig.4/13

Fig.4/10

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 6

operation/ maintenance

While making sure the dirty water tank is resting on the

base, place the rear of the tank into the base of the

cleaner, push down on the handle until it latches.

Replace top of dirty water tank by pressing it into place

(Fig 4/16).

5. Maintenance

Brush removal and replacement

NOTE: The plug must be removed from socket outlet

before cleaning or maintaining the appliance.

Remove the water tank switch off and unplug carpet

washer.

Flip the cleaner on its side to expose the nozzle base.

Lift out the floating brush bar by pressing the two

latches and pulling it gently (Fig 5/1).

Replace floating brushbar (Fig 5/2).

Cleaning the tank filter

IMPORTANT: Do not use any detergents or boiling

water to wash the filters. Vax recommends

checking the filters every time the dirty water tank is

emptied.

NOTE: All filters must be in place before using your

machine.

Remove the dirty water tank from the unit.

Remove the filter cover from the back of the tank.

Separate the filter from the filter cover.

The filter can be rinsed in warm water (max. 40

°C)

IMPORTANT: Ensure filter is fully dry before

replacing back into the machine.

Fig.4/16

Fig.5/1

Fig.5/2

24hr

Fig.5/6

40° C max

Fig.5/5

Fig.5/3

1 2

Fig.5/4

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 7

vax.co.uk

troubleshooting / uk service & help

6. Troubleshooting

WARNING: To reduce the risk of personal injury,

unplug the vacuum cleaner before performing

maintenance or troubleshooting checks.

PROBLEM: The cleaner won't run.

Cause: Not properly plugged into electrical outlet.

Solution: Plug in firmly.

Cause: No electricity in electrical outlet.

Solution: Check fuse or breaker.

Cause: ON/off switch not turned on.

Solution: Push on/off switch to ‘on’.

Cause: Blown fuse/tripped breaker.

Solution: Reset circuit breaker or replace fuse.

PROBLEM: Cleaner won’t pick up/loss of suction.

Cause: Dirty water tank is full.

Solution: Switch off and unplug cleaner. Empty dirty

water tank as shown in Section 4.

Cause: Dirty water tank not installed correctly.

Solution: Refer to page 6/7 for fitting information.

Cause: Obstruction in hose/nozzle.

Solution: Remove hose and clear obstruction.

PROBLEM: Liquid escaping from the carpet washer.

Cause: Dirty water tank is full.

Solution: Switch off and unplug cleaner. Empty dirty

water tank as shown in Section 4.

Cause: Dirty water tank not installed correctly.

Solution: Refer to page 6/7 for fitting information.

Cause: Solution tank not installed correctly.

Solution: Make sure the tank is securely locked in place

PROBLEM: Clean solution won’t dispense.

Cause: Solution tank not installed correctly.

Solution: Make sure the tank is securely locked in place.

Cause: Solution tank empty.

Solution: Refill tank. Refer to page 5 for instructions.

Cause: Handle not fitted correctly.

Solution: Ensure handle is fitted correctly.

7. UK Service & Help

(UK) 0844 412 8455

(ROI) 1-800 928 308

Monday-Friday 8.30am to 6.30pm

Saturday-Sunday 9.00am to 5.00pm

Any queries or concerns about using your Vax, call the

Vax Careline. Please make a note of the model number

and serial number of your Vax before calling. For the

nearest Vax Service Agent, please call the Vax Careline or

visit vax.co.uk

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 8

technical specification

8. Technical Specification

Voltage: 220-240V ~50Hz

Wattage: 700 W

Capacity: Clean water tank - 2.6 litres

Dirty water tank - 1.8 litres

Cord length: 6m

Weight: 5.5kg

Subject to technical change without notice.

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 9

vax.co.uk

This page has been left intentionally blank.

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 10

This page has been left intentionally blank.

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 11

---

EEC STATEMENT OF COMPLIANCE

Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the

Vax W91-RS-B Series and W90-RS-B Series is manufactured in compliance with the following Directives:

Safety: 2006/95/EC Low Voltage Directive

EMC: 2004/108/EC Electromagnetic Compatibility Directive

Waste electrical products should not be disposed of with household waste. Please recycle where

facilities exist. Check with your Local Authority or retailer for recycling advice.

Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK

email: info@vax.co.uk - website: vax.co.uk

W91-RS-B Series User Guide v1.3.qxd:User Guide 7/10/10 17:21 Page 12

Vax Rapide Spring Clean Anniversary Edition Owner's manual

Brand: Vax

Model: Rapide Spring Clean Anniversary Edition

Category: Vacuum cleaners

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Vax Rapide Spring Clean Anniversary Edition Owner's manual

This manual is also suitable for

Vax Rapide Spring Clean Anniversary Edition Owner's manual

Related papers

Other documents