Explore Scientific SM60020000000 Owner's manual

Brand
Explore Scientific
Model
SM60020000000
Type
Owner's manual

This manual is also suitable for

EN
INSTRUCTION MANUAL
About this Instruction Manual
These operating instructions are to be considered a component of the device.
Please read the safety instructions and the operating instructions carefully before use.
Keep these instructions for renewed use at a later date. When the device is sold or given to someone
else, the instruction manual must be provided to the new owner/user of the product.
GENERAL WARNINGS
• Risk of electric shock — This device contains electronic components that operate via a
power source (batteries). Children should only use the device under adult supervision. Only
use the device as described in the manual; otherwise, you run the risk of an electric shock.
• Choking hazard — Children should only use the device under adult supervision. Keep
packaging material, like plastic bags and rubber bands, out of the reach of children, as these
materials pose a choking hazard.
• Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert
the batteries correctly. Leaking battery acid can lead to chemical burns. Avoid contact of
battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the
aected region immediately with a plenty of water and seek medical attention.
• Risk of re/explosion — Do not expose the device to high temperatures. Use only the
recommended batteries. Do not short-circuit the device or batteries, or throw them into a re.
Excessive heat or improper handling could trigger a short-circuit, a re, or an explosion.
• Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer
will contact the Service Centre and can send the device in to be repaired, if necessary.
• Use only the recommended batteries. Always replace weak or empty batteries with a new,
complete set of batteries at full capacity. Do not use batteries from dierent brands or with
dierent capacities. The batteries should be removed from the unit if it has not been used for
a long time.
SCOPE OF DELIVERY
Sensor, Operating instructions, 2x CR2032 batteries.
BEFORE YOU BEGIN
• We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we
recommend using lithium batteries.
• Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power
requirements.)
• Insert batteries before rst use, matching the polarity in the battery compartment.
2x CR2032 Batteries are required.
EC Declaration of Conformity
Hereby, Bresser GmbH declares that the equipment type with part number: SM60020
is in compliance with Directive: 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
www.bresser.de/download/SM60020/CE/SM60020_CE.pdf
FCC DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-
tions: (1) this device may not cause harmful interference, and (2) this device must accept any inter-
ference received, including interference that may cause undesired operation. Please note that
changes or modications not expressly approved by the party responsible for compliance could void the us-
er’s authority to operate the equipment.
NOTES ON CLEANING
• Remove the batteries before cleaning.
• Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do
not use any cleaning uid.
• Protect the device from dust and moisture.
WARRANTY & SERVICE
The regular guarantee period is 2 years and begins on the day of purchase. To benet from an
extended voluntary guarantee period as stated on the gift box, registration on our website is required.
You can consult the full guarantee terms as well as information on extending the guarantee period
and details of our services at www.bresser.de/warranty_terms. Would you like detailed instructions for
this product in a particular language? Then visit our website via the link below (QR code) for available
versions. Alternatively you can also send an email to [email protected] or leave a message on
+49 (0) 28 72 – 80 74-220*. Please always state your name, precise address, a valid phone number
and email address, as well as the article number and name.
*Number charged at local rates in Germany (the amount you will be charged per phone call will depend
on the tari of your phone provider); calls from abroad will involve higher costs.
www.bresser.de/download/SM60020
MANUAL DOWNLOAD:
www.bresser.de/warranty_terms
SERVICE AND WARRANTY:
OVERVIEW
1. LED indicator
- Blinks once during transmission.
2. [ REFRESH ] key
3. [ CHANNEL ] rotatory selection switch
- Assign the sensor to Channel 1,2,3,4,5,6 or 7.
4. [ RESET ] key
5. Battery compartment
- Accommodates 2 x CR2032 button cells.
6. Battery door screw
7. Sensor metal probes
8. Moisture sensor
GETTING STARTED
1. Select the sensor channel by using
[CHANNEL ] rotatory selection
switch.
For example: Channel 1 is selected.
2. Drive the battery door screw counter
clockwise to open the battery door.
Art.No.: SM60020
Soil moisture Sensor
EN
INSTRUCTION MANUAL
IT
ISTRUZIONI PER L’USO
DE
BEDIENUNGSANLEITUNG
FR
MODE D'EMPLOI
ES
MANUAL DE INSTRUCCIONES
3. Insert 2 x CR2032 button cells into
the battery compartment. Make
sure you insert them the right way
according to the polarity information
marked on the battery compartment.
x
2
4. Cover the battery door and drive the
door screw clockwise to close the
battery door.
Note:
Ensure the water tight O-ring is properly
aligned in place to ensure water resistant.
Note:
- Once the channel is assigned to a Wireless sensor, you can only change it by
removing the batteries or resetting the unit.
- After replacing the batteries of the wireless sensor or the unit fails to receive wireless
sensor signal of a specied channel, press [ SENSOR ] key on the console unit to
manually receive the sensor signal again.
WIRELESS SENSOR SIGNAL RECEIVING (DISPLAY CONSOLE)
This soil sensor can support dierent 7CH console, user can base on the following step
to setup the display console.
1. In normal mode, press the [ SENSOR ] key of the console once to start receiving
the sensor signal of current on displaying channel. The signal icon will ash.
For example, when CH 1 is displayed, pressing [ SENSOR ] key will start receive for
CH 1 only.
2. The signal icon will ash until the reception succeeded. If no signal is received within
5 minutes the icon will disappear.
The icon blinks once every time
when incoming wireless sensor
signal is received (every 60s)
Weak wireless sensor
signal
Fair wireless sensor signal
Bad / no wireless
sensor signal
3. If the signal for Ch 1~7 has discontinued and does not recover within 15 minutes,
the temperature and humidity will display “Er” for the corresponding channel.
4. If the signal does not recover within 48 hours, the “Er” display will become
permanent. You need to replace the batteries of the “Er” channel’s sensors and then
press [ SENSOR ] key to pair up with the sensors per each “Er” channel again.
Note:
The operation or signal icons of dierent display consoles may be dierent, please refer
to the user manual of your display console for more detail.
TEMPERATURE DISPLAY
On the display of the console which the soil sensor is linked to, temperature reading will
be displayed.
SOIL MOISTURE DISPLAY
Soil moisture can be claried into 5 dierent levels: Very Dry, Dry , Moist, Wet and Very
Wet.
To determine the moisture of soil, the sensor calibrate the moisture into 16 points, and
correlate them into percentage value:
Points Percentage Level
1 0%
Very Dry
2 7%
3 13%
4 20%
5 27%
6 33%
Dry
7 40%
8 47%
9 53%
10 60%
Moist11 67%
12 73%
13 80%
Wet
14 87%
15 93%
Very Wet
16 99%
Note:
The measurement accuracy of the sensor can be aected by the soil condition. For
example, the loose soil may get lower moisture level that compare with the dense soil.
LOW BATTERY ICON
If the sensor is low in battery, the low battery icon “
” will display on the LCD of the
display console.
Note:
On the display console, the low battery icon will only appear when the corresponding
channel is displaying.
SENSOR PLACEMENT
Select the suitable installation site that insert the sensor probes into the soil around
100mm (4 inch) and sensor should place within 30 meters of the display console to get
the best transmission performance.
Display
console
Soil sensor
placement
100mm
(4 inch)
30m
(100 feet)
Soil
Note:
Signal transmission range of the sensor will be gradually reduced as sensor is inserted
deeper into the soil. To achieve best transmission range, install the sensor on the same
plain of view as the display console.
REFRESH THE READING ON DISPLAY CONSOLE
The sensor transmits once every 5 minutes automatically to the display console. User
may also press the [ REFRESH ] key on the sensor to manually refresh the readings if
necessary - please note the refresh may take a few seconds up to a minute.
Note:
Some battery operated display consoles may not support this function, please check your
retailer to get more information.
IMPORTANT NOTE
- Read and keep these instructions.
- Do not subject the unit to excessive force, shock, dust, temperature or humidity.
- Do not cover the ventilation holes with any items such as newspapers, curtains etc.
- Technical specications and user manual contents for this product are subject to
change without notice.
SPECIFICATIONS
Dimensions (W x H x D) 65 x 257.5 x 23.5 mm
Main power 2 x CR2032 button cell
Operating temperature range
-40°C ~ 60°C ( -40°F ~ 140°F ) do not recommend
under freeze condition
RF frequency 868Mhz (EU, UK) / 917Mhz (AU) / 915Mhz (US)
RF Transmission interval 5 minute
RF transmission range
(Place on soil ground)
Up to 30m (100 feet) line of sight
DISPOSAL
Dispose of the packaging materials properly, according to their type, such as paper
or cardboard. Contact your local waste-disposal service or environmental authority
for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
As per the Directive 2002/96/EC of the European Parliament on waste electrical
and electronic equipment and its adaptation into German law, used electronic
devices must be collected separately and recycled in an environmentally friendly manner.
In accordance with the regulations concerning batteries and rechargeable batteries,
disposing of them in the normal household waste is explicitly forbidden. Please
make sure to dispose of your used batteries as required by law — at a local collection
point or in the retail market. Disposal in domestic waste violates the Battery Directive.
Batteries that contain toxins are marked with a sign and a chemical symbol.
Cd¹ Hg² Pb³
1
battery contains cadmium
2
battery contains mercury
3
battery contains lead
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
www.bresser.de/warranty_terms
SERVICE AND WARRANTY:
www.bresser.de/download/SM60020
MANUAL DOWNLOAD:
Errors and technical changes reserved. • Con riserva di errori e modiche tecniche. • Irrtümer
und technische Änderungen vorbehalten. • Sous réserve d’erreurs et de modications
techniques. • Queda reservada la posibilidad de incluir modicaciones o de que el texto
contenga errores.
Manual_SM60020000000_Soil-Sensor_en-it-de-fr-es_EXPSC_v112019a
Explore Scientific GmbH
Gutenbergstr. 2 · DE-46414 Rhede · Germany
www.bresser.de · [email protected]
EU
Explore Scientific, LLC
1010 S. 48th Street, Springdale, AR 72762
www.explorescientificusa.com
USA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Explore Scientific SM60020000000 Owner's manual

Brand
Explore Scientific
Model
SM60020000000
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents