OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN COMPRENDRE LE
MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DEL
OPERADOR.
Catalog No.
No de Cat.
Catálogo No.
6140-6
6141
6145
HEAVY-DUTY SANDERS/GRINDERS
EXTRA ROBUSTE PONCEUSE-RECTIFIEUSE
LIJADORAS/ESMERILADORAS HEAVY-DUTY
page 2
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS.
WORK AREA
ELECTRICAL SAFETY
PERSONAL SAFETY
TOOL USE AND CARE
SERVICE
GENERAL SAFETY RULES
4. Grounded tools must be plugged into an outlet properly
installed and grounded in accordance with all codes and
ordinances. Never remove the grounding prong or modify
the plug in any way. Do not use any adaptor plugs. Check
with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should electrically
malfunction or break down, grounding provides a low resistance
path to carry electricity away from the user.
5. Double Insulated tools are equipped with a polarized plug
(one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install a polarized outlet. Do not change
the plug in any way. Double insulation eliminates the need for
the three wire grounded power cord and grounded power supply
system.
6. Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk
of electric shock if your body is grounded.
7. Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
8. Do not abuse the cord. Never use the cord to carry the tools
or pull the plug from an outlet. Keep cord away from heat,
oil, sharp edges or moving parts. Replace damaged cords
immediately. Damaged cords increase the risk of electric shock.
9. When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords are rated
for outdoor use and reduce the risk of electric shock.
10. Stay alert, watch what you are doing, and use common sense
when operating a power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or medication. A
moment of inattention while operating power tools may result in
serious personal injury.
11. Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves away
from moving parts. Loose clothes, jewelry, or long hair can be
caught in moving parts.
12. Avoid accidental starting. Be sure switch is off before
plugging in. Carrying tools with your finger on the switch or
plugging in tools with the switch on invites accidents.
13. Remove adjusting keys or wrenches before turning on the
tool. A wrench or a key that is left attached to a rotating part of the
tool may result in personal injury.
14. Do not overreach. Keep proper footing and balance at all
times. Proper footing and balance enables better control of the tool
in unexpected situations.
15. Use safety equipment. Always wear eye protection. Dust
mask, non-skid safety shoes, hard hat, or hearing protection must
be used for appropriate conditions.
16. Use clamps or other practical way to secure and support
the workpiece to a stable platform. Holding the work by hand
or against your body is unstable and may lead to loss of control.
17. Do not force tool. Use the correct tool for your application.
The correct tool will do the job better and safer at the rate for which
it is designed.
18. Do not use tool if switch does not turn it on or off. Any tool
that cannot be controlled with the switch is dangerous and must be
repaired.
19. Disconnect the plug from the power source before making
any adjustments, changing accessories, or storing the tool.
Such preventive safety measures reduce the risk of starting the tool
accidentally.
20. Store idle tools out of reach of children and other untrained
persons. Tools are dangerous in the hands of untrained users.
21. Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained tools with sharp cutting edge are less likely to
bind and are easier to control. Do not use a damaged tool. Tag
damaged tools “Do not use” until repaired.
22. Check for misalignment or binding of moving parts, break-
age of parts, and any other condition that may affect the
tool’s operation. If damaged, have the tool serviced before
using. Many accidents are caused by poorly maintained tools.
23. Use only accessories that are recommended by the manu-
facturer for your model. Accessories that may be suitable for
one tool, may become hazardous when used on another tool.
24. Tool service must be performed only by qualified repair
personnel. Service or maintenance performed by unqualified per-
sonnel could result in a risk of injury.
25. When servicing a tool, use only identical replacement parts.
Follow instructions in the Maintenance section of this
manual. Use of unauthorized parts or failure to follow Maintenance
Instructions may create a risk of electric shock or injury.
1. Keep your work area clean and well lit. Cluttered benches and
dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases, or dust.
Power tools create sparks which may ignite the dust or fumes.
3. Keep bystanders, children, and visitors away while operat-
ing a power tool. Distractions can cause you to lose control.
Protect others in the work area from debris such as chips and
sparks. Provide barriers or shields as needed.
page 3
1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments.
2. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running
over rated speed can fly apart and cause injury.
3. Make sure all wheel flanges and other mounting hardware are in good condition and are always used properly. Defective or
missing parts may damage the wheels and other accessories. Always use mounting hardware supplied with the tool.
4. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its
own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
5. Keep hands away from all cutting edges and moving parts.
6. Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a
MILWAUKEE
service facility for a free
replacement.
7. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause
cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in
a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic
particles.
SPECIFIC SAFETY RULES — SANDERS
FUNCTIONAL DESCRIPTION
1. Side handle
2. Grinding wheel
3. Lock lever
4. Wheel guard
5. Spindle lock button
6. Side handle sockets
7. Paddle trigger (under body of tool)
RPM
10,000
10,000
10,000
Volts
AC/DC
120
120
120
Cat.
No.
6140-6
6141
6145
Specifications
Amps
5.5
5.5
5.5
Watts
600
600
600
Spindle
Size
5/8" - 11
5/8" - 11
1/2" - 13
Wheel
Size
4 -1/2"
5"
4 -1/2"
Min.
Wheel
RPM
Rating
12,000
12,000
12,000
1
6
2
4
5
3
Amperes
Double Insulated
Symbology
Canadian Standards
Association
Underwriters
Laboratories, Inc.
Volts Alternating Current
/Direct Current
No Load Revolutions
per Minute (RPM)
7
page 4
WARNING!
TOOL ASSEMBLY
Grounded tools require a three wire extension cord. Double insulated
tools can use either a two or three wire extension cord. As the distance
from the supply outlet increases, you must use a heavier gauge exten-
sion cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the required minimum
wire size.
The smaller the gauge number of the wire, the greater the capacity of the
cord. For example, a 14 gauge cord can carry a higher current than a 16
gauge cord. When using more than one extension cord to make up the
total length, be sure each cord contains at least the minimum wire size
required. If you are using one extension cord for more than one tool, add
the nameplate amperes and use the sum to determine the required mini-
mum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure it is marked
with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable
for outdoor use.
• Be sure your extension cord is properly wired and in good electrical
condition. Always replace a damaged extension cord or have it
repaired by a qualified person before using it.
• Protect your extension cords from sharp objects, excessive heat
and damp or wet areas.
GROUNDING EXTENSION CORDS
Grounded Tools:
Tools with Three Prong Plugs
Tools marked “Grounding Required”
have a three wire cord and three
prong grounding plug. The plug must
be connected to a properly grounded
outlet (See Figure A). If the tool should
electrically malfunction or break
down, grounding provides a low re-
sistance path to carry electricity
away from the user, reducing the risk
of electric shock.
Improperly connecting the grounding wire can
result in the risk of electric shock. Check with a
qualified electrician if you are in doubt as to
whether the outlet is properly grounded. Do not
modify the plug provided with the tool. Never
remove the grounding prong from the plug. Do
not use the tool if the cord or plug is damaged. If
damaged, have it repaired by a
MILWAUKEE
service facility before use. If the plug will not fit
the outlet, have a proper outlet installed by a
qualified electrician.
Nameplate
Amperes
0 - 5
5.1 - 8
8.1 - 12
12.1 - 15
15.1 - 20
Extension Cord Length
25'
16
16
14
12
10
75'
16
14
12
10
10
100'
14
12
10
10
--
150'
12
10
--
--
--
200'
12
--
--
--
--
Recommended Minimum Wire Gauge
for Extension Cords*
* Based on limiting the line voltage drop to five
volts at 150% of the rated amperes.
50'
16
16
14
12
10
READ AND SAVE ALL INSTRUCTIONS
FOR FUTURE USE.
The grounding prong in the plug is connected through the green wire
inside the cord to the grounding system in the tool. The green wire in the
cord must be the only wire connected to the tool's grounding system and
must never be attached to an electrically “live” terminal.
Your tool must be plugged into an appropriate outlet, properly installed
and grounded in accordance with all codes and ordinances. The plug
and outlet should look like those in Figure A.
Double Insulated Tools:
Tools with Two Prong Plugs
Tools marked “Double Insulated” do
not require grounding. They have a
special double insulation system
which satisfies OSHA requirements
and complies with the applicable
standards of Underwriters Labora-
tories, Inc., the Canadian Standard
Association and the National Electri-
cal Code. Double Insulated tools may
be used in either of the 120 volt out-
lets shown in Figures B and C.
WARNING!
Fig. A
Fig. B
Fig. C
Installing Side Handle
The side handle may be installed on the top of the gear case or on either
side of gear case for right or left handed use. Position side handle in the
location which offers best control and guard protection. To install, thread
side handle into side handle socket on desired side of gear case and
tighten securely.
Wear safety goggles or glasses with side
shields. Always unplug tool before attaching or
removing accessories. Only use accessories
specifically recommended for these tools. Oth-
ers may be hazardous. Protect others in work
area from debris such as chips and sparks.
Provide barriers or shields as needed.
page 5
OPERATION
WARNING!
To reduce the risk of injury, wear safety goggles
or glasses with side shields. Unplug the tool
before changing accessories or making adjust-
ments.
Starting and Stopping the Motor
Plug in the tool. To start the tool, squeeze the paddle trigger. Release the
paddle trigger to stop tool.
1. To start the tool, squeeze the paddle trigger.
2. To stop the tool, release the paddle trigger.
Sanding Disc and Grinding Wheel Selection
Use sanding discs and grinding wheels that are:
• correct size as written on tool's nameplate.
• correct wheel type and grit for the job.
• rated at or above the RPM listed in the "WARNING" section on
the tool's nameplate.
Use backing pads, adapters, and other accessories that are:
• correct size for tool and for sanding disc or grinding wheel.
• rated at or above the RPM listed in the "WARNING" section on
the tool's nameplate.
• the proper accessory for the job.
Installing Backing Pad and Sanding Discs (Fig. 1)
1. Unplug tool and place it upside down on a level surface as shown.
Remove any accessories from spindle.
2. Slip backing pad onto spindle with flat side away from gear case.
Place sanding disc on backing pad and secure assembly to spindle
with disc nut.
3. To tighten, press the spindle lock button while turning disc nut clock-
wise.
4. To remove backing pad and sanding disc, unplug tool and reverse
procedure.
Sanding (Fig. 2)
1. Use a clamp, vise or other practical means to hold your work, free-
ing both hands to control your tool. Firmly grasp body of tool and
side handle before starting and while tool is in operation. Allow
sanding disc to come to full speed before beginning to sand.
2. Hold Sander/Grinder at 5° to 15° angle as shown to ensure proper
sanding pressure and control. Too great an angle will result in too
much pressure and could cause excessive wear to the disc and
workpiece. Too small an angle will reduce control.
3. Use long, sweeping, side to side strokes, advancing forward to
produce the desired finish.
Fig. 1
Gear Case
Spindle
Backing Pad
Disc Nut
Sanding Disc
Fig. 2
For best result use only this portion of disc
Hold at a 5° to 15° angle
Ceramic
Lasts up to 3 times
longer than aluminum
oxide discs. For
general metal work-
ing. Ideal for tough
jobs.
Aluminum
Zirconia Bi-Cut
Unique grit pattern is
arranged in clusters
for faster stock re-
moval and cleaning.
Ideal for removing
paint from cars,
boats, etc. without
clogging.
Aluminum
Oxide
For fast cutting, gen-
eral purpose discs
for most metal jobs.
Best for cold-rolled
steel, stainless steel
or metals requiring
tough, fast cutting,
long lasting abra-
sives.
Sanding Disc and Grinding Wheel Material
Sanding discs and grinding wheels are made of various materials and
are designed for different jobs. Be sure that you choose the proper
sanding disc or grinding wheel for the job you plan to do.
Selecting Sanding Discs & Grit
Refer to the table below to select the correct type of sanding disc for
your job. Generally, use 24 or 36 grit for heavy stock removal; 50, 60, or
80 grit for medium stock removal and 120 grit for finishing. Always begin
with a coarse grit, using successively finer grits to obtain the desired
finish. See Catalogor a complete list of
MILWAUKEE
sanding discs.
To reduce the risk of personal injury and
damage to the tool, use ONLY accessories
rated at or above the RPM listed on the
“WARNING” section of the tool's nameplate.
WARNING!
page 6
Removing Welds or Hammer Marks
When removing welds or hammer marks, limit coarse sanding to the
immediate area. Use successively finer grits to smooth surface.
Cross Sanding
When finishing a surface that has been prepared by a coarse disc or
wheel, sand at right angles to the strokes made by the coarser disc.
Finishing marks left from previous sanding are easily seen and removed
for a uniform finish. Failure to cross sand when changing from a coarse
disc to a finishing disc may result in deep scratches and circular marks.
Finishing Metal
Constantly move across the surface. Work faster on curved surfaces
where contact areas are smaller and pressure is greater. Flat areas may
appear at the end of the stroke when pressure is too heavy. Ease up on
pressure at end of each stroke and when reversing strokes.
Troubleshooting
Deep scratches and circular marks can result from:
• Using too coarse a grit
• Using a partially glazed disc
• Dirt or loose metal on the workpiece
• Failure to sand across the grain when changing from coarse
to finishing discs
• Failure to use closed coated discs to reduce the problem
of grains working loose and scratching the workpiece
Bluish discoloration of metal surface indicates:
• Excessive heat caused by circular motion in a small area
• Excessive pressure
• Use of worn out or glazed discs
Inspecting Wheels
Always handle wheels carefully to avoid damage. Before installing any wheel,
always inspect it for cracks. If wheel is cracked, discard it to prevent others
from using it.
Care of Grinding & Cut-Off Wheels
Grinding and cut-off wheels should be protected from:
• wetness and extreme humidity.
• any type of solvent.
• extreme changes in temperature.
• dropping and bumping.
Grinding and cut-off wheels should be stored:
• in an organized way so wheels can be removed without dis-
turbing or damaging other wheels.
• with their safety information.
Grinding and cut-off wheels should NOT be:
• dropped.
• rolled.
• bumped.
If any wheel is dropped, rolled, bumped, subjected to extreme changes
in temperature, or has come into contact with solvents or wetness,
discard wheel immediately.
Installing, Removing and Adjusting the Guard (Fig. 3 & 4)
The guard must be used when using the tool as a grinder. The guard
should be removed when using tool as a sander.
1. To install the guard, unplug the tool and place it upside down on a
level surface.
2. Remove any accessories from the spindle.
3. Line up the four tabs with the four slots (Fig. 4) and then press the
guard down onto the tool.
4. Press in the lock lever and rotate the guard to one of the five detent
slots. The lock lever must engage with one of the detents. (Fig. 3)
To reduce the risk of injury:
• ALWAYS use the proper guard.
• ALWAYS properly install the guard.
• ALWAYS hold the tool firmly with both
hands before beginning grinding.
• NEVER use a wheel that has been
dropped.
• NEVER bang grinding disc onto work.
• NEVER grind without proper safety
equipment.
WARNING!
Only use wheels with Maximum Safe
Operating Speed rated at or above the RPM
listed on the “WARNING” section of the tool's
nameplate. This speed is based on the
strength of the wheel, allowing for a reason-
able measure of safety. It is not meant to imply
a best or most efficient operating speed. Do
not exceed the Maximum Safe Operating
Speed.
WARNING!
To reduce the risk of injury, the operator
should be instructed in the use, care and
protection of grinding wheels.
WARNING!
Fig. 3
Lock lever
Fig. 4
Tab slot
Tab slot
Tab slot
Tab slot
Lock lever
Guard
Lock lever must engage
one of five detents
page 7
Grinding
A Type “27” guard must be installed
when using a grinding wheel to provide
maximum protection for the operator if
the wheel should break.
WARNING!
Flange nut position for 1/8" or less thick wheels
Flange nut position for 1/4" thick wheels
Fig. 5
Flange nut
Boss
Spindle
Grinding wheel
Flange
Fig. 6
Boss
Flange nut
Spindle
Grinding wheel
Flange
Selecting Wheels
Grinding is the cutting action of thousands of abrasive grains on the face
of a grinding wheel. When grinding metals such as steel and iron, choose
an aluminum oxide grinding wheel. Select a silicon carbide grinding wheel
for stone and concrete. Use cotton reinforced wheels for non-ferrous
metals.
Type 27 reinforced 1/8" cut-off wheels are suited for small cut-off and
shallow notching operations only.
Installing Grinding Wheels (Fig. 5 & 6)
1. When guard is properly positioned, place flange on spindle with
flange facing away from tool.
1. Depending on your job, position the guard to provide maximum pro-
tection for the operator (Fig. 7).
2. If you have just installed a grinding wheel or are just beginning a
period of work, test wheel by letting it spin for one minute before
applying it to the workpiece.
NOTE: Out-of-balance wheels can mar workpiece, damage the tool,
and cause stress to wheel that may cause wheel failure.
3. Firmly grasp body of tool and side handle before starting and while
using tool. Allow wheel to come to full speed before starting to grind.
4. When grinding, hold sander/grinder at a 5
o
to 15
o
angle as shown, using
constant pressure for a uniform finish. Too great an angle causes
concentrated pressure on small areas which may gouge or burn work
surface.
5. Control pressure and surface contact between disc and workpiece.
Too much pressure slows cutting speed.
2. Place selected wheel on spindle and align with flange. Position flange
nut according to wheel thickness as shown (Fig. 5 & 6).
3. Press the spindle lock button while turning flange nut clockwise.
Tighten securely with the spanner wrench provided.
4. To remove wheel, unplug tool and reverse procedure.
Grinding (Fig. 7 & 8)
To reduce the risk of injury, do not use
the spindle lock button to stop the
spindle while the tool is in use or is
coasting after shut-off. This will result in
tool damage.
WARNING!
5. To remove the guard, unplug tool and place it upside down on a
level surface. Remove any accessories from spindle.
6. Press in the lock lever and rotate the guard to line up the four tabs
with the four slots as shown in (Fig. 4).
7. Lift the guard straight up and away from the tool.
8. To adjust the guard, press in the lock lever and rotate the guard to
one of the five detents (Fig. 3).
Fig. 7
Operator's Zones
Fig. 8
Hold at a 5° to 15° angle
page 8
Everyone in the area must wear protective
clothing and safety goggles or face shields.
Fatigued wires and residue will fly off the
brush with considerable force, causing the
potential for serious injuries.
WARNING!
Using Cut-Off Wheels (Fig. 9)
Type “1” cut-off wheels are suited for small cut-off and shallow notch-
ing operations only.
Installing Wire Cup Brushes (Fig. 10)
1. Unplug tool and place it upside down on a level surface as shown.
Remove any accessories from spindle.
1. Firmly grasp body of tool and side handle before starting and while
using tool. Allow wheel to come to full speed before starting.
2. When using a cut-off wheel, hold sander/grinder as shown, using
only the edge of the wheel.
3. Control pressure and surface contact between disc and workpiece.
Too much pressure slows cutting speed.
Fig. 9
2. To install, thread wire cup brush onto spindle. Press the spindle lock
button while tightening brush with a 7/8" open end wrench (not
provided with tool).
3. To remove wire cup brush, unplug tool and reverse procedure.
Using Wire Wheel Brushes (Fig. 11)
Never exceed Maximum Safe Operating
Speed of brush. Do not use a damaged
brush or one which is functioning im-
properly (throwing wires, out-of-bal-
ance, etc.). These conditions increase
the possibility of further brush failure
and possible injury. Discard and replace
damaged brushes immediately.
WARNING!
Wire wheel brushes are useful for removing rust, scale, burrs, weld
slag, etc. A wide variety of wire brushes are available for many applica-
tions.
Test wire wheel brush for balance and loose or damaged wires by
running tool at no load speed for at least one minute before applying it to
your work. During this time, no one should stand in front of or in line with
it. When applying brush to work, avoid using too much pressure. This
causes over-bending of wires and heat build-up resulting in premature
wire breakage, rapid dulling and reduced brush life. Instead of using
more pressure, try a wire wheel brush with more aggressive cutting
action (increased wire size, decreased wire length or different brush
type, i.e., knot type instead of crimped wire type).
Using the face of a cut-off wheel (as in
grinding) will cause the wheel to crack
and break, resulting in serious personal
injury.
WARNING!
A Type “1” guard must be installed when
using a cut-off wheel to provide maxi-
mum protection for the operator if the
wheel should break.
WARNING!
Because the wires on wire wheel
brushes are directed towards the opera-
tor, a guard must be used to protect the
operator when fatigued wires break.
WARNING!
Wire wheel brush
Fig. 11
guard
Fig. 10
Wire cup brush
page 9
Maintaining Tools
Keep your tool in good repair by adopting a regular maintenance pro-
gram. Before use, examine the general condition of your tool. Inspect
guards, switches, tool cord set and extension cord for damage. Check
for loose screws, misalignment, binding of moving parts, improper mount-
ing, broken parts and any other condition that may affect its safe opera-
tion. If abnormal noise or vibration occurs, turn the tool off immediately
and have the problem corrected before further use. Do not use a dam-
aged tool. Tag damaged tools “DO NOT USE” until repaired
(see “Repairs”).
Under normal conditions, relubrication is not necessary until the motor
brushes need to be replaced. After six months to one year, depending on
use, return your tool to the nearest
MILWAUKEE
service facility for the
following:
• Lubrication
• Brush inspection and replacement
• Mechanical inspection and cleaning (gears, spindles, bearings,
housing, etc.)
• Electrical inspection (switch, cord, armature, etc.)
• Testing to assure proper mechanical and electrical operation
Cleaning
Clean dust and debris from vents. Keep the tool handles clean, dry and
free of oil or grease. Use only mild soap and a damp cloth to clean your
tool since certain cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include: gasoline, turpentine,
lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia. Never use flammable or
combustible solvents around tools.
MAINTENANCE
For a complete listing of accessories refer to your
MILWAUKEE
Electric
Tool catalog. To obtain a catalog, contact your local distributor or a
service center listed on the back cover of this operator’s manual.
ACCESSORIES
Repairs
If your tool is damaged, return the entire tool to the nearest service
center listed on the back cover of this operator’s manual.
WARRANTY
WARNING!
To reduce the risk of injury, always unplug
your tool before performing any maintenance.
Never disassemble the tool or try to do any
rewiring on the tool's electrical system. Contact
a
MILWAUKEE
service facility for ALL repairs.
WARNING!
To reduce the risk of injury, electric shock and
damage to the tool, never immerse your tool in
liquid or allow a liquid to flow inside the tool.
WARNING!
To reduce the risk of injury, always unplug the
tool before attaching or removing accessories.
Use only specifically recommended accesso-
ries. Others may be hazardous.
Every
MILWAUKEE
product is warranted to be free from defects in
material and workmanship.
MILWAUKEE
will repair or replace any product
which examination proves to be defective in material or workmanship.
Limitations: This warranty does not cover: 1) repairs made or at-
tempted by other than
MILWAUKEE
or
MILWAUKEE
Authorized Service
Station personnel; 2) normal wear and tear; 3) abuse; 4) misuse;
5) improper maintenance; 6) continued use after partial failure; 7) tools
that have been modified; or product used with an improper accessory.
Battery Packs are warranted for one (1) year from the date of purchase.
Should a problem develop, return the complete product to any
MILWAUKEE
Factory Service Center or
MILWAUKEE
Authorized Ser-
vice Station, freight prepaid and insured. If inspection shows the prob-
lem is caused by a defect in material or workmanship, all repairs or a
replacement will be made at no charge and the product will be returned,
transportation prepaid. No other warranty, written or verbal, is authorized.
THE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN ARE
EXCLUSIVE. IN NO EVENT SHALL
MILWAUKEE
BE LIABLE FOR ANY
INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, INCLUDING
LOSS OF PROFITS.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED WHETHER FOR MERCHANTABILITY OR FITNESS FOR PARTICULAR
USE OR PURPOSE.
This warranty gives you specific legal rights. You may also have
other rights that vary from state to state. In those states that do not
allow the exclusion of implied warranties or limitations of inciden-
tal or consequential damages, the above limitations or exclusions
may not apply to you.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
58-14-3350d2 06/02 Printed in U.S.A.
MILWAUKEE ELECTRIC TOOL CORPORATION
A Company within the Atlas Copco Group
13135 West Lisbon Road • Brookfield, Wisconsin, U.S.A. 53005
UNITED STATES
MILWAUKEE Service
To locate the
factory
SERVICE CENTER or
authorized service station nearest you, call
1-800-414-6527
TOLL FREE • NATIONWIDE
Monday-Friday • 8:00 AM - 4:30 PM • Local Time
In addition, there is a worldwide network of
distributors ready to assist you. Check your
“Yellow Pages” under “Tools-Electric” for the names
of those nearest you.
Corporate Product Service Support -
Warranty and Technical Information
Brookfield, Wisconsin USA
1-800-729-3878
For further information on
factory
SERVICE CENTER
or authorized service station locations,
visit our website at:
www.mil-electric-tool.com
CANADA
Service MILWAUKEE
Milwaukee Electric Tool (Canada) Ltd
755 Progress Avenue
Scarborough, Ontario M1H 2W7
Tel. (416) 439-4181
Fax: (416) 439-6210
En outre le réseau de distributeurs est à la disposition de la
clientèle d’un océan à l’autre. Consultez les pages jaunes de
l’annuaire téléphonique pour l’adresse du centre le plus près
de chez vous.
In addition, there is a worldwide network of distributors ready to
assist you. Check your “Yellow Pages”under “Tools-Electric”
for the names of those nearest you.
MEXICO
Servicios de MILWAUKEE
Milwaukee Electric Tool
División de : Atlas Copco Mexicana S.A. de C.V.
Blvd. Abraham Lincoln no. 13
Colonia Los Reyes Zona Industrial
Tlalnepantla, Edo. México C.P. 54073
Tels. 5565-1414 5565-4720
Fax: 5565-0925
Además se cuenta con una red nacional de distribuidores
listos para apoyarlo. Vea en las “Páginas Amarillas” sección
“Herramientas Eléctricas”.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Milwaukee 6140 Manuel utilisateur
- español: Milwaukee 6140 Manual de usuario
Related papers
Other documents
-
DeWalt DWE4214 Installation guide
-
-
Bosch 1853-5 User manual
-
Bosch Power Tools 1853-5 User manual
-
-
Stanley FMEG220 User manual
-
DeWalt D28135 User manual
-
Stanley FMEG210 User manual
-
Black & Decker KFBEG125 User manual
-
Black & Decker BEG010 User manual