Siemens Slider SL 20 Owner's manual

Page is loading ...

11

Thank you for buying the slider SL20 steam

station, the new steam-ironing system from

Siemens.

Carefully read through the operating instructions

for the appliance and safeguard them for future

reference.

Introduction

These instructions for use contain valuable information

about the unique features of this system and some

hints to make ironing easier for you.

We hope that you enjoy ironing with this steam

station.

Important

Open out the first page of the booklet, this will help you

to understand how the appliance works.

This appliance complies with international safety

standards.

This appliance has been designed exclusively for

domestic use and must not be used for industrial

purposes.

This appliance must only be used only for the purposes

for which it was designed, i.e. as an iron. Any other

use will be considered improper and consequently

dangerous. The manufacturer will not be held

responsible for any damage arising from misuse or

improper use.

General safety instructions

• This appliance is to be connected and used in

accordance with the information stated on its

characteristics plate.

• This appliance must be connected to an earthed

socket. If it is absolutely necessary to use an

extension cable, make sure that it is suitable for 16A

and has a socket with an earth connection.

• The iron should not be used if it has been dropped,

if there are visible signs of damage or if it is leaking

water. It must be checked by an authorized Technical

Service Centre before it can be used again.

• If the safety fuse fitted in the appliance blows, the

appliance will be rendered inoperative. To restore

normal operation the appliance will have to be taken

to an authorised Technical Service Centre.

• In order to avoid that, under unfavourable mains

conditions, phenomena like transient voltage

drops or lighting fluctuations can happen, it is

recommended that the iron is connected to a power

supply system with a maximum impedance of 0.27

 . If necessary, the user can ask the public power

supply company for the system impedance at the

interface point.

• This appliance is not intended to be used by persons

(including children) with reduced physical, sensory

or mental capacities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning the use of the appliance by

a person responsible for their safety.

• Children should be supervised to ensure that they

do not play with the appliance.

• Remove the plug from the socket before filling the

appliance with water or before pouring out the

remaining water after use.

• The appliance must never be placed directly under

the tap to fill the water tank.

• The appliance must be used and placed on a stable

surface.

• When placed on its stand, make sure that the

surface on which the stand is placed is stable.

• The iron must not be left unattended while it is

connected to the supply mains.

• Unplug the appliance from the mains supply after

each use, or if a fault is suspected.

• The electrical plug must not be removed from the

socket by pulling the cable.

• Never immerse the iron or steam tank in water or

any other fluid.

• Do not leave the appliance exposed to weather

conditions (rain, sun, frost, etc.).

• With the aim of avoiding dangerous situations, any

work or repair that the appliance may need, e.g.

replacing a faulty mains cable, must only be carried

out by qualified personnel from an Authorised

Technical Service Centre.

Important :

• This appliance reaches high temperatures and

produces steam during use, this could cause scalds

or burns in case of improper use.

• The steam hose, base station and in particular the

iron can get hot when used.

• Never aim the steam at people or animals.

• Do not allow the power cable to come into contact

with the soleplate when it is hot.

Description

1. Water tank

2 Removable iron pad

3 Steam hose storage fixing

4 Carrying handles

5 Mains cable storage compartment

6 Mains cable

7 Steam hose

8 “Energy Saving” button

*

9 “Steam ready” pilot light

10 Variable steam control

*

11 “Refill water tank” pilot light

12 Illuminated main power button (0/I)

13 Housing with internal steam generator

14 Temperature control knob

15 Steam release button

16 Steam release button “XTRM steam”

*

17 Iron pilot light

18 Soleplate

* Model dependent

en

12

en

Preparations (A)

1. Remove any label or protective covering from the

soleplate.

2. Place the appliance horizontally on a solid, stable

surface. You may remove the iron pad from the

appliance and place the iron on it on another solid,

stable, horizontal surface.

3. Fill the water tank, making sure not to pass the level

mark.

4. Unwind the mains cable (6) fully and plug it into an

earthed socket.

5. Set the main power button (12) to the “I” position.

6. The “Steam ready” indicator lamp (9) will light up

after several minutes, indicating that the appliance

is ready to use.

The steam generator will take more time to reach

“Steam ready” state only upon the initial heating up,

or after performing the de-scaling operation (Calc’n

clean).

When water is already present in the steam

generator during regular use, heat up time to reach

the operating temperature will be faster.

7. This appliance has a built-in water level sensor. The

“refill water tank” indicator (11) will light when the

water tank is empty.

Important:

• Normal tap water can be used.

To prolong the optimum steam function, mix tap

water with distilled water 1:1. If the tap water in

your district is very hard, mix tap water with distilled

water 1:2.

You can inquire about the water hardness with your

local water supplier.

• The water tank can be filled at any time while using

the appliance.

• To avoid damage and/or contamination of the wa-

-

ter tank and the boiler, do not put perfume, vinegar,

starch, descaling agents, additives or any other type of

chemical product into the water tank.

Any damage caused by the use of the

aforementioned products, will make the

guarantee void.

• The iron is not designed to rest on its heal. Please

always position it horizontally on the iron pad (2).

• The iron pad can be placed into the specially

designed recess on the appliance or somewhere

suitable alongside the ironing area.

Never rest the iron on the appliance without

the iron pad!.

• During it first use the iron may produce certain

vapours and odours, along with white particles on

the soleplate, this is normal and it will stop after a

few minutes

• While the steam release button is pressed, the water

tank may produce a pumping sound, this is normal,

indicating that water is being pumped to the steam

tank.

Setting the temperature

1. Check the ironing instruction label on the garment to

determine the correct ironing temperature.

2. Turn the temperature selector (14) to the required

setting:

• Synthetics

•• Silk – Wool

••• Cotton – Linen

3. The indicator lamp (17) will remain lit while the iron is

heating and go out as soon as the iron has reached

the selected temperature.

Tips:

• Sort your garments out based on their cleaning

symbol labels, always starting with clothes that have

to be ironed at the lowest temperatures.

• If you are not sure what the garment is made of then

begin ironing at a low temperature and decide on

the correct temperature by ironing a small section

not usually seen when worn

Ironing with steam (B)

1. Turn the temperature selector (14) to the required

setting.

2. Set the amount of steam to suit your needs, using

the variable steam control (10) (model dependent).

For normal use, please choose one of the following

recommended settings:

Temperature Steam setting

•

••

•••

3. Press the steam release button to release steam.

Attention:

When ironing on a lower temperature setting “•”.

• If the appliance has variable steam control (10), set

the variable steam control to its lowest position .

• If the appliance does not have variable steam con-

-

trol, press the steam release button only for a few

seconds at a time when ironing at lower tempera--

tures.

In both cases, if you find that water is dripping out

of the soleplate, set the temperature selector (14) to

a higher position (take care that the garment can be

ironed on this heat temperature setting).

“Pulse steam” function

This appliance has a special function for tackling

difficult creases.

When the steam release button is activated, the steam

generator will give three powerful shots of steam so

that the steam reaches even deeper into the fabrics.

13

1. Set the temperature selector (14) on “• • •”

2. Press the steam release button (15) on the bottom

of the handle two times shortly (double-click)

or (model dependent)

Shortly press the steam release button (16) on the

top of the handle.

Remark : It is possible to stop the shots of steam by

pressing the steam button shortly again.

“XTRM steam” function

(model dependent)

The “XTRM steam” function helps to make a faster

softening of very stubborn garments like Jeans or linen

tablecloth. When activating the “XTRM steam” button

(16) the steam generator produces an extra amount of

steam. The function should be used during intervals of a

few seconds, to be the most effective.

1. set the temperature selector (14) on “•••”

2. press the “XTRM steam” button (16).

Important:

• The steam hose may get hot if you are ironing for

long periods.

•

Note: Some water drops may appear when you use

the “Pulse steam” or the “XTRM steam” function for

the first time. The water drops will disappear after

you have used the function for some time.

Ironing without steam

1. Begin ironing but without pressing the steam release

button.

Vertical steam (C)

1. Set the temperature control to the “•••” or “max”

position.

2. You can steam iron curtains and hanging garments

(jackets, suits, coats...) by placing the iron in a

vertical position and pressing the steam release

button.

Never direct the steam jet at garments that are

being worn.

Never aim the steam at people or animals.

Energy saving “eco” button

(model dependent)

If the “Energy saving” button (8) is switched on, the

energy consumption of the appliance will be reduced,

by means of automatic reduction of electricity and

water consumption. A good ironing result can be

obtained for most of the garments.

Use the normal energy setting only for thick and highly

wrinkled fabrics.

Note: If you work with the “Energy saving”

function, the variable steam regulation and

temperature regulation can still be used as

recommended.

Cleaning & Maintenance

Always unplug the appliance from the mains

supply before carrying out any cleaning or

maintenance operation on it.

1. After ironing, pull out the plug and allow the

appliance to cool down before cleaning.

2. Wipe the housing, handle and iron body with a

damp cloth.

3. If the soleplate is soiled with dirt or scale, clean it

with a damp cloth.

4. Never use abrasive products or solvents.

Storing the appliance (D)

1. Always allow the appliance to cool down before

storing it.

2. Set the main power to the “0” position and

disconnect the mains cable.

3. Place the iron on the iron pad, standing on the

soleplate.

4. Store the mains cable in the storage compartment

(5) and the steam hose in the storage fixing (3). Do

not wrap the cords too tight.

5. Use the carrying handles (4) on the sides when

moving the appliance.

Fabric protection soleplate cover (E)

(model dependent)

The fabric-protection soleplate cover is used for steam-

ironing delicate garments at maximum temperature

without damaging them. Use of the soleplate cover

also does away with the need for a cloth to prevent

shine on dark materials.

It is advisable to first iron a small section on the inside

of the garment to see if it is suitable.

To attach the soleplate cover to the iron, place the tip

of the iron into the end of the soleplate cover and pull

the elastic strap over the lower rear of the iron until

it fits tightly. To release the soleplate cover, pull the

elastic strap and remove the iron.

The fabric-protection soleplate cover may be purchased

from the customer service or specialist shops:

Accessory code

(After-sales)

Name of accessory

(Specialist outlets)

571510 TZ20450

en

14

en

Trouble shooting

Problem Possible causes Solution

The steam generator

does not come on.

• There is a connection problem.

• The main power button is not

switched on.

• Check the mains cable, the plug and the

socket.

• Set the main power button (12) to the “I”

position.

The iron does not

heat up.

• The main power button is not

switched on.

• The temperature control knob is set

to the “min” position.

• Set the main power button (12) to the “I”

position.

• Set the temperature control knob (14) to

the desired position.

The iron begins to

smoke when switched

on.

• During first use: Certain components

on the appliance have been lightly

greased at the factory and may

produce a little smoke when initially

heated.

• During later use: the soleplate may

be soiled.

• This is completely normal and will stop

after a short while.

• Clean the soleplate according to the

cleaning instructions in this manual.

Water flows through

the holes on the sole

plate.

• The steam function is being used

before it has reached temperature.

• The water is condensing inside the

pipes because steam is being used

for the first time or has not been used

for a long time.

• Reduce the steam flow when ironing at

low temperatures (Variable steam control

(10)).

• Point the iron away from the ironing area

and press the steam release button until

steam is produced.

“Calc‘n clean” (F)

Cleaning the Boiler

To extend the life of your steam generator and to To

extend the life of your steam generator and to avoid

any build up of scale, it is essential that you rinse out

the boiler after several hours of use (approximately after

50 hours). If the water is hard, increase the frequency.

Do not use descaling agents for rinsing out the boiler,

as they could damage it.

1. Check that the appliance is cold and unplugged for

more than 2 hours, and that the water tank (1) is

empty.

2. Place your appliance on the edge of your kitchen

sink.

3. Remove the plastic cover located on the bottom of

the appliance by turning it to the position.

4. Unscrew the boiler drainage plug using a coin.

5. Holding your steam generator in upside down

position, and using a jug, fill the boiler (in the base

unit) with 1/4 litre of water

6. Shake the base unit for a few moments and then

empty it completely over a sink or bucket. To obtain

the best result, we recommend that this operation is

done twice.

Important: before re-closing, make sure no water

remains in the boiler.

7. Replace and tighten up the boiler drainage plug with

a coin.

8. Insert and close the plastic cover by turning it to the

position.

Rinsing the iron steam chamber (G)

Caution! Risk of burns!

This procedure helps to remove scale particles out of

the steam chamber.

Carry it out approximately every 2 weeks, if the water

in your area is very hard.

a) Ensure that the iron is cooled down.

b) Set the temperature selector (14) of the iron to the

“min” position.

c) Fill the tank with tap water.

d) Plug in the mains cable and set the main power

switch (12) to the “I” position.

e) Wait until the “steam ready” indicator lamp (9) lights

up.

f) If the steam station has steam regulator (10), set it to

the maximum position .

g) Hold the iron over the sink or a container to collect

the water.

h) Press the steam release button (15) and gently

shake the iron. Boiling water and steam will come

out, carrying scale and or deposits that might be

there. This could take approximately 5 minutes.

i) Set the temperature selector (14) of the iron to the

“max” position, without pressing the steam release

button (15). The water in the steam chamber will

start evaporating. Wait until all the water inside the

chamber has been evaporated.

j) To clean the soleplate, immediately rub off any

residue by running the hot iron over dry cotton

cloth.

15

en

Advice on disposal

Our goods come in optimised packaging. This basically

consists in using non-contaminating materials which

should be handed over to the local waste disposal

service as secondary raw materials. Your local town

council can give you information about how to dispose

of obsolete appliances.

This appliance is labelled in

accordance with European Directive

2002/96/EG concerning used electrical

and electronic appliances (waste

electrical and electronic equipment -

WEEE).

The guideline determines the framework for

the return and recycling of used appliances as

applicable throughout the EU.

Problem Possible causes Solution

Dirt comes out

through the sole plate.

• There is a build-up of scale or

minerals in the steam tank.

• Chemical products or additives have

been used.

• Use tap water mixed 50% with dis tilled

or demineralised water. If the tap water in

your district is very hard, mix tap water with

distilled water 1:2.

• Clean the sole plate with a damp cloth.

• Never add products to the boiler water.

The iron does not

produce any steam.

• The boiler is not switched on or the

water tank is empty.

• The steam regulator is set to the

minimum position.

• Set the main power button (12) to the “I”

position and/or fill the water tank.

• Increase the steam flow by turning the

steam control (10).

The ironed gar ment

turns dark and/or

sticks to the soleplate.

• The selected temperature is too high

and has damaged the garment.

• Select a suitable temperature for the

material being and clean the sole plate

with a damp cloth.

The soleplate turns

brown.

• This is a regular consequence of

usage.

• Clean the soleplate regularly with a damp

cloth.

The appliance makes

a pumping sound.

• Water is being pumped into the

steam tank.

• The sound will not stop.

• This is normal.

• If the sound will not stop, do not use

the steam generator and contact an

authorised technical service centre.

Loss of pressure

during ironing.

Steam release button activated during

a long period of time.

Use the steam release button with intervals.

This improves the ironing result as the

textiles will be dried and stay smooth better.

Waterspots appear

on the garment during

ironing.

May be caused by steam condensed

on the ironing board.

Wipe the textile cover of the ironing board,

and iron the spots without steam to dry

them.

Water spots appear

on the garment during

use of the “XTRM

steam” function

Water spots are caused by steam

condensation in the hose when cooling

down after use.

Water drops stop coming out of the

soleplate after using the “XTRM steam”

function for some time.

The hose gets hot

during use.

This is normal. It is caused by the

steam passing throug the hose during

steam ironing.

Place the hose on the opposite side so that

you can not touch the hose during ironing

Water leakage from

the boiler

Drainage plug located at the bottom of

the appliance is loose.

Tighten up boiler drainage plug with a coin

The iron does not stop

steaming after placing it

on the pad.

“Pulse steam” function activated by

double click.

Just press the trigger once again and the iron

will stop steaming at once.

If the above does not solve the problem, get in touch with authorized technical service.

You can download this manual from the local homepages of Siemens.

Page is loading ...

Siemens Slider SL 20 Owner's manual

Siemens Slider SL 20 Owner's manual

in other languages

Related papers

Other documents