Curt Manufacturing 11342 Owner's manual

Type
Owner's manual

Curt Manufacturing 11342 is a weight-carrying hitch designed for use with a Nissan Sentra 2.0. It has a gross load capacity of 1,000 lbs and a tongue weight of 100 lbs. The hitch is made of steel and has a black powder coat finish. It comes with all the necessary hardware for installation.

The Curt Manufacturing 11342 is a versatile hitch that can be used for a variety of purposes, such as towing a trailer, carrying a bike rack, or mounting a cargo carrier. It is easy to install and can be done in about an hour.

Here are some of the features of the Curt Manufacturing 11342:

  • Gross load capacity of 1,000 lbs

Curt Manufacturing 11342 is a weight-carrying hitch designed for use with a Nissan Sentra 2.0. It has a gross load capacity of 1,000 lbs and a tongue weight of 100 lbs. The hitch is made of steel and has a black powder coat finish. It comes with all the necessary hardware for installation.

The Curt Manufacturing 11342 is a versatile hitch that can be used for a variety of purposes, such as towing a trailer, carrying a bike rack, or mounting a cargo carrier. It is easy to install and can be done in about an hour.

Here are some of the features of the Curt Manufacturing 11342:

  • Gross load capacity of 1,000 lbs
Parts List DESCRIPTION
PART NUMBER
QTY
ITEM CARRIAGE BOLT1/2-13 x 1 1/221 7/16 " FISHWIRE TOOLCM-438-FW12 CARRIAGE BOLT7/16-14 x 123 .250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP72
4HEX FLANGE NUT7/16-14
25 HEX FLANGE NUT
HFN 121326 .250" TRUNK PAN SPACERCM-11342-TPS
17
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY AUXILIARY STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
1,000 100
25
60
NISSAN SENTRA 2.0
9/01/2009
11342
120
24727
1) Remove spare tire from trunk, remove rubber plugs as shown.
2) Install trunk pan spacer with (2) 1/2" carriage bolts.
3) Enlarge two holes in bumper beam which line up with outer two holes in hitch plate.
4) Fishwire (2) 7/16" carriage bolts with SP7 spacers from end of bumper beam to enlarged holes.
5) Raise hitch into position and finger tighten in place with (2) 1/2" and (2) 7/16" flange nuts.
6) Torque all 7/16" hardware to 50 ft.-lb. and all 1/2" hardware to 75 ft.-lb.
7) Return spare tire to trunk.
-DRILLING REQUIRED
-FISHWIRING REQUIRED
-SPARE TIRE REMOVAL REQUIRED
21
7
6
3
4
HOLE ENLARGEMENT
REQUIRED FOR INSTALL
TRUNK PAN
5
DESIGNED FOR USE WITH
BALL MOUNT # D-20 / 45520
  • Page 1 1

Curt Manufacturing 11342 Owner's manual

Type
Owner's manual

Curt Manufacturing 11342 is a weight-carrying hitch designed for use with a Nissan Sentra 2.0. It has a gross load capacity of 1,000 lbs and a tongue weight of 100 lbs. The hitch is made of steel and has a black powder coat finish. It comes with all the necessary hardware for installation.

The Curt Manufacturing 11342 is a versatile hitch that can be used for a variety of purposes, such as towing a trailer, carrying a bike rack, or mounting a cargo carrier. It is easy to install and can be done in about an hour.

Here are some of the features of the Curt Manufacturing 11342:

  • Gross load capacity of 1,000 lbs

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI