Juno JBKM131D0 User manual

JBKM131D0

User Manual

Microwave

combi-oven

CONTENTS

Safety information 2

Safety instructions 4

Product description 7

Control panel 8

Before first use 10

Daily use 10

Microwave mode 11

Clock functions 16

Automatic programmes 17

Using the accessories 18

Additional functions 19

Hints and tips 21

Care and cleaning 41

Troubleshooting 42

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damage that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Children between 3 and 8 years of age and persons with

very extensive and complex disabilities shall be kept away

from the appliance unless continuously supervised.

• Children of less than 3 years of age should be kept away

from the appliance unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep children and pets away from the appliance when it

operates or when it cools down. Accessible parts may

become hot during use.

• If the appliance has a child safety device, it should be

activated.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• Only a qualified person must install this appliance and

replace the cable.

• WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to avoid

touching heating elements.

• Always use oven gloves to remove or put in accessories or

ovenware.

• Before carrying out any maintenance, disconnect the

appliance from the power supply.

• WARNING: Ensure that the appliance is switched off

before replacing the lamp to avoid the possibility of electric

shock.

• Do not use the appliance before installing it in the built-in

structure.

• Do not use a steam cleaner to clean the appliance.

• Do not use harsh abrasive cleaners or sharp metal

scrapers to clean the glass door since they can scratch the

surface, which may result in shattering of the glass.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service

Centre or similarly qualified persons to avoid an electrical

hazard.

• Do not activate the appliance when it is empty. Metal parts

inside the cavity can create electric arcing.

• Metallic containers for food and beverages are not allowed

during microwave cooking. This requirement is not

applicable if the manufacturer specifies size and shape of

metallic containers suitable for microwave cooking.

• If the door or door seals are damaged, the appliance must

not be operated until it has been repaired by a qualified

person.

• Only a qualified person can carry out any service or repair

operation that involves the removal of a cover which gives

protection against exposure to microwave energy.

• Do not heat liquids and other foods in sealed containers.

They are liable to explode.

• Use only utensils that are suitable for use in microwave

ovens.

• When heating food in plastic or paper containers, keep an

eye on the appliance due to the possibility of ignition.

• The appliance is intended for heating food and beverages.

Drying of food or clothing and heating of warming pads,

slippers, sponges, damp cloth and similar may lead to risk

of injury, ignition or fire.

• If smoke is emitted, switch off or unplug the appliance and

keep the door closed in order to stifle any flames.

• Microwave heating of beverages can result in delayed

eruptive boiling. Care must be taken when handling the

container.

• The contents of feeding bottles and baby food jars shall be

stirred or shaken and the temperature checked before

consumption, in order to avoid burns.

• Eggs in their shell and whole hard-boiled eggs should not

be heated in the appliance since they may explode, even

after microwave heating has ended.

• The appliance should be cleaned regularly and any food

deposits removed.

• Failure to maintain the appliance in a clean condition could

lead to deterioration of the surface that could adversely

affect the life of the appliance and possibly result in a

hazardous situation.

SAFETY INSTRUCTIONS

Installation

WARNING! Only a qualified

person must install this

appliance.

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Do not pull the appliance by the handle.

• Keep the minimum distance from other

appliances and units.

• Install the appliance in a safe and

suitable place that meets installation

requirements.

• The appliance is equipped with an

electric cooling system. It must be

operated with the electric power supply.

• The built-in unit must meet the stability

requirements of DIN 68930.

Cabinet minimum

height (Cabinet un‐

der the worktop mini‐

mum height)

444 (460) mm

Cabinet width 560 mm

Cabinet depth 550 (550) mm

Height of the front of

the appliance

455 mm

Height of the back of

the appliance

440 mm

Width of the front of

the appliance

595 mm

Width of the back of

the appliance

559 mm

Depth of the appli‐

ance

567 mm

Built in depth of the

appliance

546 mm

Depth with open

door

882 mm

Ventilation opening

minimum size. Open‐

ing placed on the

bottom rear side

560x20 mm

Mains supply cable

length. Cable is

placed in the right

corner of the back

side

1500 mm

Mounting screws 3.5x25 mm

Electrical connection

WARNING! Risk of fire and

electric shock.

• All electrical connections should be

made by a qualified electrician.

• The appliance must be earthed.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Always use a correctly installed

shockproof socket.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by

our Authorised Service Centre.

• Do not let mains cables touch or come

near the appliance door or the niche

below the appliance, especially when it

operates or the door is hot.

• The shock protection of live and

insulated parts must be fastened in

such a way that it cannot be removed

without tools.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• If the mains socket is loose, do not

connect the mains plug.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type

fuses removed from the holder), earth

leakage trips and contactors.

• The electrical installation must have an

isolation device which lets you

disconnect the appliance from the

mains at all poles. The isolation device

must have a contact opening width of

minimum 3 mm.

• This appliance is supplied with a main

plug and a main cable.

Use

WARNING! Risk of injury,

burns and electric shock or

explosion.

• This appliance is for household use

only.

• Do not change the specification of this

appliance.

• Make sure that the ventilation openings

are not blocked.

• Do not let the appliance stay

unattended during operation.

• Deactivate the appliance after each

use.

• Be careful when you open the

appliance door while the appliance is in

operation. Hot air can release.

• Do not operate the appliance with wet

hands or when it has contact with

water.

• Do not apply pressure on the open

door.

• Do not use the appliance as a work

surface or as a storage surface.

• Open the appliance door carefully. The

use of ingredients with alcohol can

cause a mixture of alcohol and air.

• Do not let sparks or open flames to

come in contact with the appliance

when you open the door.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

• Do not use microwave function to

preheat the oven.

WARNING! Risk of damage to

the appliance.

• To prevent damage or discoloration to

the enamel:

– do not put aluminium foil directly on

the bottom of cavity of the

appliance.

– do not put water directly into the hot

appliance.

– do not keep moist dishes and food

in the appliance after you finish the

cooking.

– be careful when you remove or

install the accessories.

• Discoloration of the enamel or stainless

steel has no effect on the performance

of the appliance.

• Use a deep pan for moist cakes. Fruit

juices cause stains that can be

permanent.

• This appliance is for cooking purposes

only. It must not be used for other

purposes, for example room heating.

• Always cook with the oven door closed.

• If the appliance is installed behind a

furniture panel (e.g. a door) make sure

the door is never closed when the

appliance is in operation. Heat and

moisture can build up behind a closed

furniture panel and cause subsequent

damage to the appliance, the housing

unit or the floor. Do not close the

furniture panel until the appliance has

cooled down completely after use.

Care and cleaning

WARNING! Risk of injury, fire,

or damage to the appliance.

• Before maintenance, deactivate the

appliance and disconnect the mains

plug from the mains socket.

• Make sure the appliance is cold. There

is the risk that the glass panels can

break.

• Replace immediately the door glass

panels when they are damaged.

Contact the Authorised Service Centre.

• Make sure the cavity and the door are

wiped dry after each use. Steam

produced during the operation of the

appliance condensates on cavity walls

and can cause corrosion.

• Clean regularly the appliance to

prevent the deterioration of the surface

material.

• Fat and food remaining in the appliance

can cause fire and electric arcing when

the microwave function operates.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use any abrasive products,

abrasive cleaning pads, solvents or

metal objects.

• If you use an oven spray, follow the

safety instruction on it's packaging.

• Do not clean the catalytic enamel (if

applicable) with any kind of detergent.

Internal lighting

WARNING! Risk of electric

shock.

• The type of light bulb or halogen lamp

used for this appliance is for household

appliances only. Do not use it for house

lighting.

• Before replacing the lamp, disconnect

the appliance from the power supply.

• Only use lamps with the same

specifications.

Service

• To repair the appliance contact the

Authorised Service Centre.

• Use original spare parts only.

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the

mains supply.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

• Remove the door catch to prevent

children or pets from becoming trapped

in the appliance.

PRODUCT DESCRIPTION

General overview

1 2

Control panel

Electronic programmer

Heating element

Microwave generator

Lamp

Fan

Shelf support, removable

Shelf positions

Accessories

Wire shelf

For cookware, cake tins, roasts.

Baking tray

For cakes and biscuits.

CONTROL PANEL

Electronic programmer

21 3 4 5 6 7 8 9 10 11

Use the sensor fields to operate the appliance.

Sensor

Field

Function Description

- DISPLAY Shows the current settings of the appliance.

ON / OFF To activate and deactivate the appliance.

OPTIONS To set an oven function or an automatic pro‐

gramme (only when the appliance is activated).

MICROWAVE To activate the Microwave function. When the

function is active, press this sensor field to change

the microwave power.

TEMPERATURE /

FAST HEAT UP

To set and see the cavity temperature or the core

temperature sensor temperature (if present). If you

press it and hold for three seconds, it turns the

Fast heat up function ON and OFF.

DOWN To move down in the menu.

UP To move up in the menu.

OK / Microwave

Quick Start

To confirm a selection or setting. To activate the

Microwave function when the appliance is deacti‐

vated. Each press of this sensor field adds 30 sec‐

onds to the duration.

OVEN LIGHT To activate or deactivate the oven lamp.

Sensor

Field

Function Description

CLOCK To set the clock functions.

MINUTE MINDER To set the Minute Minder.

Display

A B C

DEFG

A. Oven function symbol

B. Temperature / time of day / microwave power

display

C. Clock / Residual heat display / Minute Minder

D. Residual heat indicator

E. Indicators for the clock functions

F. Heat-up indicator / Fast Heat Up indicator

G. Number of an oven function / programme

Other indicators of the display:

Symbol Name Description

Automatic programme You can choose an automatic programme.

Microwave function The microwave function operates.

kg / g An automatic programme with a weight in‐

put operates.

h / min A clock function operates.

Watt You can set the power for the microwave

function.

Temperature / Fast heat up The function operates.

Temperature The current temperature is indicated.

Temperature You can change the temperature.

Light You deactivated the light.

Minute minder The minute minder function operates.

Heat up indicator

If you turn on the heating function,

appears. The bars show that the

temperature in the oven increases or

decreases.

When the oven is at the set temperature,

the bars go off the display.

BEFORE FIRST USE

WARNING! Refer to Safety

chapters.

To set the Time of day refer to

"Clock functions" chapter.

Initial Cleaning

Remove all accessories and removable

shelf supports from the oven.

Refer to "Care and cleaning" chapter.

Clean the oven and the accessories

before the first use.

Put the accessories and the removable

shelf supports back to their initial position.

Setting the time

After the first connection to the mains, all

symbols in the display are on for some

seconds. For the subsequent few seconds

the display shows the software version.

After the software version goes off, the

display shows h and 12:00.

1. Touch or to set the hours.

2. Touch .

3. Touch or to set the minutes.

4. Touch or .

The Temperature / Time display shows

the new time.

Changing the time

You can change the time of day only when

the appliance is on.

Touch again and again until flashes

in the display.

To set the new time of day, refer to

"Setting the time".

DAILY USE

WARNING! Refer to Safety

chapters.

Heating Functions

Oven func‐

tion

Application

True Fan

Cooking

To bake on up to two

shelf positions at the

same time and to dry

food.

Set the temperature 20 -

40 °C lower than for Con‐

ventional Cooking.

Pizza Func‐

tion

To bake pizza. To make

intensive browning and a

crispy bottom.

Oven func‐

tion

Application

Conventional

Cooking

To bake and roast food

on one shelf position.

Slow Cooking

To prepare tender, suc‐

culent roasts.

Bottom Heat

To bake cakes with

crispy bottom and to pre‐

serve food.

Defrost

To defrost food (vegeta‐

bles and fruit). The de‐

frosting time depends on

the amount and size of

the frozen food.

Oven func‐

tion

Application

Keep Warm

To keep food warm.

Grill

To grill flat food and to

toast bread.

Frozen Foods

To make convenience

food (e.g. french fries,

potato wedges or spring

rolls) crispy.

Turbo Grilling

To roast larger meat

joints or poultry with

bones on one shelf posi‐

tion. To make gratins and

to brown.

The lamp may turn off

automatically at a temperature

below 60 °C during some oven

functions.

Setting the heating function

1. Turn on the oven with .

The display shows the set temperature,

the symbol and the number of the heating

function.

2. Press or to set a heating

function.

3. Press or the oven starts

automatically after 5 seconds.

If you turn on the oven and do not set any

heating function or programme, the oven

turns off automatically after 20 seconds.

Changing the temperature

Press or to change the

temperature in steps: 5 °C.

When the oven is at the set temperature a

signal sounds and the Heat up indicator

disappears.

Checking the temperature

You can check the current temperature in

the oven when the function or programme

works.

1. Press .

The display shows the temperature in the

oven.

2. Press or the display shows again

the set temperature automatically after

5 seconds.

Fast Heat Up

Do not put food in the oven when the Fast

heat up works.

The Fast Heat Up is available only for

some heating functions. If Faulty Tone is

turned on in the settings menu, the signal

sounds if the Fast Heat Up is not available

for the set function. Refer to "Additional

functions" chapter, Using the settings

menu.

The Fast Heat Up decreases the heat up

time.

To turn on the Fast Heat Up press and

hold

for more than 3 seconds.

If the Fast Heat Up is turned on the

display shows flashing bars.

MICROWAVE MODE

WARNING! Refer to Safety

chapters.

Microwave recommendations

Place the food on a plate on the bottom of

the cavity.

Turn or stir the food halfway through the

defrosting and cooking time.

Cover the food for cooking and reheating.

Put the spoon to the bottle or glass when

heating drinks to ensure better heat

distribution.

Put the food into the oven without any

packaging. The packaged ready meals

can be put into the oven only when the

packaging is microwave safe (check

information on the packaging).

Microwave cooking

Cook food covered. If you want to keep a

crust cook food without a cover.

Do not overcook the dishes by setting the

power and time too high. The food can dry

out, burn or cause fire.

Do not use the oven to cook eggs or

snails in their shells, because they can

burst. Pierce the yolk of fried egg before

reheating it.

Pierce food with skin or peel with a fork

several times before cooking.

Cut vegetables into similar-sized pieces.

Stir liquid dishes from time to time.

Stir the food before serving.

After you turn off the oven, take the food

out and let it stand for a few minutes.

Microwave defrosting

Put the frozen, unwrapped food on a small

upturned plate with a container below it, or

on a defrosting rack or plastic sieve so

that the defrosting liquid can run off.

Remove defrosted pieces subsequently.

To cook fruit and vegetables without

defrosting them first, you can use a higher

microwave power.

Microwave suitable cookware and materials

For the microwave use only suitable cookware and materials. Use below table as a

reference.

Cookware / Material Microwave function Microwave Combi

function

De‐

frosting

Heating,

Cooking

Ovenproof glass and porcelain with no

metal components, e.g. heat-proof

glass

Non-ovenproof glass and porcelain

without any silver, gold, platinum or

other metal decorations

X X

Glass and glass ceramic made of

ovenproof / frost-proof material

Ceramic and earthenware without any

quartz or metal components and gla‐

zes which contain metal

Ceramic, porcelain and earthenware

with unglazed bottom or with small

holes, e.g. on handles

X X X

Heat-resistant plastic up to 200 °C

(please always check the plastic con‐

tainer specification before use)

Cardboard, paper X X

Cookware / Material Microwave function Microwave Combi

function

De‐

frosting

Heating,

Cooking

Clingfilm X X

Roasting film with microwave safe clo‐

sure (please always check the film

specification before use)

Roasting dishes made of metal, e.g.

enamel, cast iron

X X

Baking tins, black lacquer or silicon-

coated (please always check the bak‐

ing tins specification before use)

X X

Baking tray X X X

Wire shelf X X

Cookware for microwave use, e.g.

crisp pan

X X

Tips for the microwave

Result Remedy

You cannot find details for the amount

of food prepared.

Find details for similar type of food. Increase or

shorten the length of the cooking time according to

the following rule: double the amount - almost dou‐

ble the time, half the amount - half the time.

The food after cooking is too dry. Set shorter cooking time or select lower microwave

power and cover with material suitable for use in

the microwave.

The food is still not defrosted, hot or

cooked after the end of cooking time .

Set longer cooking time or select higher microwave

power. Note that taller dishes generally need lon‐

ger cooking time. Stir or turn food during cooking.

After the end of cooking time the food

is overheated at the edges but is still

not ready in the middle.

Next time select a lower power and a longer time.

Stir liquids, such as soup, halfway through.

Other things to think about…

• Food items have different shapes and

qualities. They are prepared in different

quantities. Because of this, the

necessary time and power for

defrosting, heating or cooking can vary.

As a rough guide: double the quantity

- almost double the time.

• The microwave creates the heat

directly in the food. Because of this, all

places cannot be heated at the same

time. You must stir or turn the heated

dishes, especially when preparing

larger quantities of food.

• The standing time is given in the

tables. Let the food stand, in the

appliance or outside it, so that the heat

is distributed more evenly.

• Adjust the power level according to

food quantity. Using high power level

with small amount of food can burn the

food or generate arcing when you use

the accessories.

• You get better results for rice if you use

flat, wide dishes.

Microwave functions

Functions Description

Microwave Creates the heat directly in the food. Use it to heat pre-prepared meals

and drinks, to defrost meat or fruit, and to cook vegetables and fish.

Combi Use it to operate the oven function and the microwave mode together.

Use it to cook food in a shorter time and brown it at the same time.

Quick Start Use it to activate the Microwave function with one touch of the sensor

field with the maximum microwave power. Operating time: 30 sec‐

onds.

Setting the Microwave function

Deactivate the appliance to use the

normal Microwave function.

1. Touch to activate the Microwave

function.

The display shows the symbol and the

default microwave power.

2. Touch or to change the

microwave power. The power setting

changes in 100 Watt steps.

3. Touch to set the DURATION. Refer

to "Setting the DURATION". Confirm

with to start the Microwave

function.

If you do not set the

DURATION and start the

Microwave function with

directly, the duration is 30

seconds. Each press of this

sensor field adds 30

seconds to the duration.

If you do not touch , the

appliance deactivates after 20

seconds.

The maximum setting of the

time for the DURATION is 90

minutes.

You can change the microwave

power (touch and then

or ) and the DURATION

(touch ) any time when the

Microwave function operates.

4. When the set time ends, an acoustic

signal sounds for 2 minutes. The

Microwave function deactivates

automatically. Touch a sensor field to

stop the acoustic signal.

To deactivate the appliance, touch .

If you touch

or open the

door, the function stops. To

start it again, touch .

The maximum time of microwave

functions depends on microwave power

you set:

MICROWAVE

POWER

MAXIMUM TIME

100 - 600 W -

More than 600 W 7 minutes

Setting the Combi function

1. Activate an oven function. Refer to

"Setting the oven function".

2. Touch and do the same steps as

when you set the Microwave function.

The Combi function is not available with

the function END, SET + GO.

If you set the END function

for the normal oven function, it

changes to the DURATION

in the Combi function.

If you set the DURATION

function for the normal oven

function, it stays active for the

Combi function. If the set

DURATION is longer than 90

minutes, it is not possible to

activate the Combi function.

When you use the Microwave function in

Combi mode the Microwave power cannot

be more than 600 W.

Setting the Quick Start function

1. Touch to deactivate the appliance.

2. Touch to activate the Quick Start

function.

Each touch of adds 30 seconds to the

duration time.

You can change the microwave

power (refer to "Setting the

Microwave function").

3. Touch to set the time for the

DURATION function. Refer to "Setting

the DURATION".

Recommended power settings for different kinds of food

The data in the table is for guidance only.

700 - 1000 W

Cooking vegetables

Searing at the start of the

cooking process

Heating liquids

500 - 600 W

Cooking egg dishes

Simmering stews

Heating one-plate

meals

Defrosting and heat‐

ing frozen meals

300 - 400 W

Melting cheese,

chocolate, but‐

ter

Simmering

rice

Heating baby

food

Cooking / Heat‐

ing delicate food

Continuing

cooking

100 - 200 W

Defrosting bread

Defrosting fruit and

cakes

Defrosting cheese,

cream, butter

Defrosting meat,

fish

CLOCK FUNCTIONS

Clock functions table

Clock function Application

COUNT UP TIMER To set the count up, which shows how long the appliance

operates. This function has no effect on the operation of

the appliance.

TIME OF DAY To show the time of day. To change the time of day, refer

to "Setting the time".

DURATION To set how long the appliance operates.

END To set when the appliance deactivates. You can use Dura‐

tion and End at the same time (Time delay) if you want the

appliance to activate and deactivate automatically later.

SET+GO To start the appliance with necessary settings with only

one touch of the sensor field any time later.

Count Up Timer

The Count Up Timer is not

activated if Duration and End

are set.

The Count Up Timer starts to count when

the appliance starts to heat.

1. To reset the Count Up Timer, touch

2. Touch until the display shows

"00:00" and the Count Up Timer starts

to count up again.

Setting the DURATION

1. Activate the appliance and set an oven

function and temperature.

2. Touch again and again until the

display shows .

flashes in the display.

3. Use or to set the minutes for

DURATION.

4. Touch to confirm.

5. Use or to set the hours for

DURATION.

If you touch or while

you set the DURATION, the

appliance switches to the

setting of the END function.

6. When the set time ends, an acoustic

signal sounds for two minutes.

and time setting flash in the display.

The appliance deactivates.

7. Touch a sensor field or open the oven

door to stop the acoustic signal.

8. Deactivate the appliance.

Setting the END

1. Activate the appliance and set an oven

function and temperature.

2. Touch again and again until the

display shows .

flashes in the display.

3. Use or to set the END and

or to confirm. First you set the

minutes and then the hours.

When the set time ends, an acoustic

signal sounds for two minutes. symbol

and the time setting flash in the display.

The appliance deactivates.

4. Touch a sensor field or open the oven

door to stop the acoustic signal.

5. Deactivate the appliance.

Setting: Set + Go

You can use the Set + Go function only

when the Duration is set.

1. Set a heating function and

temperature.

2. Set the Duration.

3. Press again and again until the

display shows flashing .

4. Press to set the Set + Go function.

The display shows and with an

indicator. This indicator shows which clock

function is activated.

5. Press a sensor field (apart from ON /

OFF) to start the Set + Go function.

Setting the MINUTE MINDER

Use the MINUTE MINDER to set a

countdown. This function has no effect on

the operation of the oven. You can set the

MINUTE MINDER at any time and also

when the appliance is off.

1. Touch .

and "00" flash in the display.

2. Use or to set the MINUTE

MINDER. First you set the seconds,

then the minutes and the hours.

3. Touch or the MINUTE MINDER

starts automatically after five seconds.

When the set time ends, an acoustic

signal sounds for two minutes and 00:00

and flash in the display.

4. Touch a sensor field or open the oven

door to stop the acoustic signal.

Setting the Time delay function

The DURATION and END can be

used at the same time, if the appliance is

to be switched on and off automatically

later. In this case, first set the DURATION

and then the END function (refer to

"Setting the DURATION" and "Setting the

END" ).

When the Time delay function

is activated, the display shows

a static symbol of the oven

function, with a dot and .

The dot shows which clock

function is on in the Clock /

residual heat display.

AUTOMATIC PROGRAMMES

WARNING! Refer to Safety

chapters.

There are 9 automatic programmes. Use

an automatic programme or recipe when

you do not have the knowledge or

experience on how to prepare a dish. The

display shows the shelf position and the

default cooking times for all automatic

programmes.

Automatic programmes

Programme number Programme name

1 MEAT

2 FROZEN VEGETABLES

3 CHICKEN, WHOLE

4 MUFFINS

5 PIZZA

6 POTATO GRATIN

7 SWEET TART

8 WHITE BREAD

9 BRAISED MEAT

Automatic programmes

1. Activate the appliance.

2. Touch .

The display shows and the number of

the automatic programme.

3. Touch or to choose the

automatic programme.

4. Touch or wait five seconds until

the appliance automatically starts to

work.

When you choose an

automatic programme with

microwave mode, the

appliance will not start

automatically if you do not

close the door. After you

close the door, confirm the

selection with .

5. When the set time ends, an acoustic

signal sounds for two minutes. The

symbol flashes.

The appliance deactivates.

6. Touch a sensor field or open the door

to stop the acoustic signal.

Automatic programmes with

weight input

If you set the weight of the meat, the

appliance calculates the roasting time.

1. Activate the appliance.

2. Touch .

3. Touch or to set the weight

programme.

The display shows: the cooking time, the

duration symbol , a default weight, a

unit of measurement (kg, g).

4. Touch or the settings save

automatically after five seconds.

The appliance activates.

5. You can change the default weight

value with or . Touch .

6. When the set time ends, an acoustic

signal sounds for two minutes.

flashes.

The appliance deactivates.

7. Touch a sensor field or open the door

to stop the acoustic signal.

USING THE ACCESSORIES

WARNING! Refer to Safety

chapters.

Inserting the accessories

Use only suitable cookware and material.

WARNING! Refer to "Hints and

tips" chapter, Microwave

suitable cookware and

materials.

Wire shelf:

Push the shelf between the guide bars of

the shelf support and make sure that the

feet point down.

Baking tray:

Push the baking tray between the guide

bars of the shelf support.

Wire shelf and baking tray together:

Push the baking tray between the guide

bars of the shelf support and the wire shelf

on the guide bars above.

Small indentation at the top

increase safety. The

indentations are also anti-tip

devices. The high rim around

the shelf prevents cookware

from slipping of the shelf.

ADDITIONAL FUNCTIONS

Using Child Lock

The Child Lock prevents an accidental

operation of the oven.

You can turn on this function when the

oven is off. Do not set a heating function.

Press and hold and at the same

time for 2 seconds. The signal sounds.

The display shows SAFE.

Repeat the action to turn off the Child

Lock.

Using the Function Lock

You can turn on the function only when

the oven works.

The Function Lock prevents an accidental

change of the oven function.

1. To turn on the function turn on the

oven.

2. Turn on an oven function or setting.

3. Touch and hold and at the

same time for 2 seconds.

A signal sounds.

Lock comes on in the display.

To turn off the Function Lock repeat step

You can turn off the oven when

the Function Lock is on. When

you turn off the oven, the

Function Lock turns off.

Using the settings menu

The settings menu lets you turn on or turn

off functions in the main menu. The

display shows SET and the number of the

setting.

Description Value to set

1 SET+GO ON / OFF

2 RESIDUAL HEAT INDICATOR ON / OFF

KEY TONE

CLICK / BEEP / OFF

4 FAULTY TONE ON / OFF

5 BRIGHTNESS LOW / MEDIUM / HIGH

6 SERVICE MENU -

7 RESTORE SETTINGS YES / NO

It is not possible to deactivate the tone of the ON / OFF sensor field.

1. Press and hold for 3 seconds.

The display shows SET1 and "1" flashes.

2. Press or to set the setting.

3. Press .

4. Press or to change the value of

the setting.

5. Press .

To exit the Settings menu, press or

press and hold .

Automatic Switch-Off

For safety reasons the oven turns off

automatically after some time, if a heating

function works and you do not change any

settings.

(°C) (h)

30 - 115 12.5

120 - 195 8.5

200 - 230 5.5

The Automatic Switch-off does not work

with the functions: Light, Duration, End

Time.

Brightness of the display

There are two modes of display

brightness:

• Night brightness - when the appliance

is deactivated, the brightness of the

display is lower between 10 PM and 6

AM.

• Day brightness:

– when the appliance is activated.

– if you touch a sensor field during

the night brightness (apart from

ON / OFF), the display goes back

to the day brightness mode for the

next 10 seconds.

– if the appliance is deactivated and

you set the Minute Minder. When

the Minute Minder function ends,

the display goes back to the night

brightness.

Page is loading ...

Juno JBKM131D0 User manual

Related papers

Other documents