Roland HP601 Owner's manual

Type
Owner's manual

Roland HP601: Experience a superior piano playing experience with our advanced digital piano, designed to inspire creativity and enhance your musical journey. Immerse yourself in authentic piano sounds, a responsive keyboard, and a variety of features that cater to aspiring pianists and seasoned musicians alike. Explore expressive playing techniques, practice effectively with built-in lessons, and connect to your favorite music apps via Bluetooth® technology. Unleash your musical potential and bring your performances to life with the Roland HP601.

Roland HP601: Experience a superior piano playing experience with our advanced digital piano, designed to inspire creativity and enhance your musical journey. Immerse yourself in authentic piano sounds, a responsive keyboard, and a variety of features that cater to aspiring pianists and seasoned musicians alike. Explore expressive playing techniques, practice effectively with built-in lessons, and connect to your favorite music apps via Bluetooth® technology. Unleash your musical potential and bring your performances to life with the Roland HP601.

Assembling the Piano
5. Place the rear board as shown in gure 4, and align the rear
board’s screw holes (four locations at the bottom) with the pedal
board’s screw holes.
* If you have diculty inserting the rear board, loosen screws
C
so it is easier to position the rear board in the stand.
6. From the front, use screws
A
(two locations) to fasten the rear
board to the hardware inside the side board.
Then use screws
B
(four locations) to fasten the rear board to the
pedal board from behind.
While you tighten the screws, correct any warping so that the top edge
of the rear board and pedal board are level.
gure 5
Screw
B
Ensure that there is
no gap between the
rear board and the
side boards.
Screw
A
2. Assembling the Piano
1. As shown in gure 6, align the screws on the bottom of the piano
unit (one each at left and right) with the hardware of the side
boards, and while slightly lifting the front edge of the piano unit,
pull it toward yourself so that the screws hook into the hardware.
* Be careful, so you do not get your ngers pinched.
2. First hand-tighten the screws
D
(two locations) two or three
rotations, and then use a screwdriver to fasten them rmly.
3. Connect the AC adaptor to the DC In jack on the bottom of the
piano unit, and connect the pedal cord to the Pedal jack from the
back (gure 7).
* Use the coated clips on the bottom of the piano unit to secure the
AC adaptor and pedal cord.
Coated clip
AC adaptor
pedal cord
gure 7
4. Loosen the music rest screws slightly (2–3 mm), insert the music
rest brackets between the screws and the body of the piano, and
turn the screws to secure the music rest while using one hand to
support the music rest.
When attaching the music rest, make sure that it is rmly inserted all the
way toward the back, and use your hand to support the music rest so
that it does not fall.
* Take care not to pinch your hand.
* Do not apply excessive force to the music rest.
* If you need to remove the music rest, loosen the screws while
using one hand to support the music rest. Detach the music rest,
and then rmly retighten the screws.
5. Use screws
E
(two locations) to fasten the headphone hook.
6. Connect the AC adaptor and power cord, and plug the power cord
into an AC outlet.
7. Adjust the Adjuster.
Lower the adjuster located below the pedal board, adjusting it so that it
contacts the oor. If the piano is placed on carpet, lower the adjuster a
little more so that it pushes slightly against the oor.
れは使わないでOKだ
います
Adjuster
gure 11
* The pedal may be damaged if there is a gap between the adjuster
and the oor.
gure 4
The wood grain should face forwards.
1
2
Please don’t get your
ngers pinched.
Pull the piano toward yourself
while keeping the front slightly
raised.
Screw
D
Screw
D
First hand-
tighten the screws two or
three rotations, and then
use a screwdriver to fasten
them rmly.
hardware
Screw
gure 6
gure 8
A
A (1 : 2)
B
B (1 : 5)
C (1 : 10)
れは使わないでOKだ
います
Screw
E
(2 pcs.)
gure 9
gure 10
Place the AC adaptor so the side with the indicator faces upwards
and the side with textual information faces downwards. The
indicator will light when you plug the AC adaptor into an AC outlet.
To AC outlet
Power cord
1. Stand Assembly
1. Open the packaging material shown in gure 1 (two pieces) by
unfolding the side with the higher pad, and then fold it back
inward.
Youll use this packaging material to align the side boards and pedal
board so that the heights of their screw holes match, making it easier to
fasten the screws.
gure 1
40%で縮小
40%で縮小
40%で縮小
pad
Open the side with
the higher pad
Fold back the
opened pad inward
2. As shown in gure 2, fasten the side board (left) (the side with the
hardware facing inward) to the pedal board. Hand-tighten the
screws
C
(two locations) two or three rotations, and then use a
screwdriver to fasten them rmly.
* If you don’t start by hand-tightening the screws, the threads
might become stripped, making it impossible to complete the
assembly.
* When attaching the pedal board, do not allow any gap to remain
between the side board and pedal board when the pieces are
assembled.
3. In the same way, use screws
C
(two locations) to fasten the side
board (right).
gure 2
Leave the pedal cord extended
Don’t allow a gap!
side
board
Two screws
C
on each side
Working from the inside of the pedal board
toward the side board, hand-tighten the
screws two or three rotations, and then use a
screwdriver to fasten them rmly.
Spread out the
packaging material, align
the height of the screw
holes in the pedal board
and the side boards, and
fasten them with screws.
4. Hold the left and right side boards, and move them upright while
preventing the pedal board from being twisted.
Deutsch Français Italiano Español Português Nederlands
1
* 5 1 0 0 0 5 7 3 6 8 - 0 1 *
To assure that assembly is carried out properly, make sure to read these instructions before you begin the assembly. Please keep these instructions
close at hand, so you can refer to them whenever you need.
Caution when assembling the unit
Make sure to enlist the help of at least one other person.
Lift the piano carefully—all the while keeping it level.
If necessary, spread out a blanket or similar material to prevent the stand or oor from being scratched during assembly.
Make sure to keep screws and any other small parts in a safe location that is out of the reach of small children, so such small parts won’t accidentally get swallowed.
Place the unit at a location that is level and sure to remain stable. The unit must never be placed on top of deep-pile carpet. Otherwise, you risk causing damage to the
pedals due to instability and unnecessary movement.
Be careful not to pinch your hands or drop this unit on your foot.
All screws should be tightened provisionally rst, then tightened later. To tighten a screw provisionally, screw it in until about half of its length is no longer visible. For a
successful assembly, compensate for any warping while you tighten the fasteners.
Do not use an electric screwdriver when tightly securing the screws. Otherwise, you risk stripping the threads.
Be careful not to pinch the pedal cord during assembly.
Caution when moving the unit
You must rst detach the music rest, close the keyboard cover, disconnect the AC adaptor, and raise the stand adjuster.
With at least one other person helping you, lift the unit horizontally and carry it, taking care not to pinch your hands or drop the unit on your feet.
1
Music rest
2
Piano main unit
3
Side board (left)
4
Side board (right)
5
Rear board
6
Pedal board
Screw (4 x 14 mm): 2 pcs.
Screw (4 x 20 mm): 4 pcs.
Screw (5 x 40 mm): 4 pcs.
Screw (5 x 20 mm): 2 pcs.
Screw (4 x 16 mm): 2 pcs.
Check the Parts
Headphone hook: 1 pcs.
1
2
3
4
5
6
* The screwdriver needed to perform the assembly is not supplied. You’ll need to have ready a Phillips
screwdriver that matches the size of the screws.
A
B
C
D
E
F
gure 3
KSC-92
Copyright © 2017 ROLAND CORPORATION
English
  • Page 1 1

Roland HP601 Owner's manual

Type
Owner's manual

Roland HP601: Experience a superior piano playing experience with our advanced digital piano, designed to inspire creativity and enhance your musical journey. Immerse yourself in authentic piano sounds, a responsive keyboard, and a variety of features that cater to aspiring pianists and seasoned musicians alike. Explore expressive playing techniques, practice effectively with built-in lessons, and connect to your favorite music apps via Bluetooth® technology. Unleash your musical potential and bring your performances to life with the Roland HP601.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI