Grizzly T27951 Owner's manual

Brand: Grizzly

Model: T27951

Type: Owner's manual

Grizzly T27951 is a single-door, four-drawer cabinet that can provide ample storage in workshops or garages. Built with a sturdy metal frame, it ensures durability and can withstand heavy loads, with a maximum capacity of 1250 lbs. Each of the four drawers has a weight limit of 175 lbs, and the shelves can hold up to 275 lbs each. The 90-degree soft-close door hinges prevent the door from slamming shut, ensuring a smooth and controlled closure. The adjustable feet allow for leveling on uneven surfaces, ensuring stability and preventing rocking or tipping.

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T27951

SINGLE-DOOR,

4-DRAWER CABINET

INSTRUCTIONS

Introduction

The Model T27951 Single-Door, 4-Drawer Cabinet

requires some assembly. Follow the instructions

below for assembly, operation, and maintenance.

Figure 1. Model T27951.

• To reduce risk of crushing injuries from

tool cabinet tipping over on you:

— Do not stand on cabinet or in drawers.

— Only open one drawer at a time.

— Only move or transport cabinet with all

drawers and door closed and locked.

— Push cabinet only (do not pull it) when

moving.

• Do not exceed weight capacities:

— Max individual drawer weight limit is

175 lbs.

— Max individual shelf weight limit

is 275 lbs.

— Max total tool cabinet weight limit

(including contents) is 1250 lbs.

• To prevent accidental tipping, ensure

adjustable feet are down and cabinet

body is level.

• Do not allow children to have unsupervised

access to cabinet.

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 10.16) #JH18542 PRINTED IN CHINA

V1.07.17

Inventory Qty

• Tool Cabinet with Drawers ........................... 1

• Cabinet Feet ................................................ 4

• Keys ............................................................. 2

Assembly

The Model T27951 comes with four adjustable

feet for leveling the cabinet.

To install feet:

1. With help from another person, lay cabinet

upside down on floor (see Figure 2).

2. Install one adjustable foot in each corner (see

Figure 2).

3. To prevent tipping or rocking, level the cabi-

net body by rotating the cabinet feet up or

down as needed.

Figure 2. Location of adjustable feet.

Adjustable Feet

Maintenance

• Use a soft, clean cloth and soapy water to

remove grease, dirt, or oil. Do not use sol-

vents or flammable cleaning liquids.

• Lubricate lock annually with graphite.

-2-

T27951 Tool Cabinet (Mfd. 10/16)

Removing & Installing Drawers

To remove a drawer:

1. Fully extend drawer and remove contents.

2. Push left locking tabs on drawer runner down

and hold, then pull right locking tabs on

drawer runner up and hold (see Figure 5).

3. Remove drawer from drawer slide.

The drawers can be removed and re-installed, if

necessary.

Figure 5. Location of drawer locking tabs.

Drawer

Runner

Adjusting Doors

To adjust doors:

1. Close door and visually confirm gap spacing

around door edge is

⁄8" all the way around

(see Figure 3).

— If door spacing is equal, no adjustments

are needed.

— If door spacing is not equal, proceed to

Step 2.

Each 90° soft-close door hinge is riveted in place.

However, the doors may be adjusted inward or

outward, and left or right, as needed.

2. Adjust door hinges using screws shown in

Figure 4.

Note: Only small adjustments, such as

⁄8

⁄4 turn at a time, are required to move

door position. Check spacing after each

adjustment.

Figure 3. Checking door gap spacing.

⁄8" Gap

Installing Shelf Supports

Each shelf comes with four shelf supports, which

fit into the channel brackets inside the cabinet

(see Figure 6), making the height of each shelf

adjustable. (Shelf supports must be mounted

evenly to function properly.)

Shelf

Support

Channel

Bracket

Figure 6. Shelf support and channel bracket.

4. To re-install drawer, extend drawer slides out

all the way, insert drawer runners into slides,

and close drawer entirely. Locking tabs will

click in place as drawer is closed, which will

fully attach drawer to slides.

Figure 4. Hinge adjustments.

In/Out

Adjustment

Right/Left

Adjustment

Locking Tab

T27951 Tool Cabinet (Mfd. 10/16)

-3-

Parts Breakdown & List

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT27951001 CABINET BODY 12 PT27951012 DOOR HANDLE

2 PT27951002 ADJUSTABLE FEET M12-1.75 X 30 13 PT27951013 DRAWER LINER

3 PT27951003 CABLE GROMMET 14 PT27951014 SHELF SUPPORT

4 PT27951004 HINGE, 90-DEG SOFT-CLOSE 15 PT27951015 FLAT HD SCR M4-.7 X 8

5 PT27951005 SHELF 16 PT27951016 DOOR LOCK W/2 KEYS

6 PT27951006 DRAWER SLIDE 17 PT27951017 DRAWER LOCK W/2 KEYS

7 PT27951007 DRAWER HANDLE 18 PT27951018 TOUCH-UP PAINT, GLOSSY BLACK

8 PT27951008 DOOR HANDLE CAP 19 PT27951019 TOUCH-UP PAINT, RED

9 PT27951009 DRAWER 7" 20 PT27951020 WARNING LABEL

10 PT27951010 DRAWER 9" 21 PT27951021 QR CODE LABEL

11 PT27951011 DOOR 22 PT27951022 GRIZZLY.COM LABEL, GOLD

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here

are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

Grizzly Cabinet Series

T27947 T27952 T27951T27948

T27953

T27950

T27949

The T27951 Single-Door, Four-Drawer Cabinet is part of our heavy-duty 10-piece storage set. These modu-

lar cabinets will enhance storage and workspace in the shop or garage, and they can be mixed and matched

to create a variety of storage solutions.

Grizzly T27951 Owner's manual

Grizzly T27951 Owner's manual

Grizzly T27951 Owner's manual

Related papers

Other documents