Miller SINGLE MOUNTING BRACKET Owner's manual

Brand: Miller

Model: SINGLE MOUNTING BRACKET

Type: Owner's manual

This manual is also suitable for

MF000000G

Miller SINGLE MOUNTING BRACKET

The Miller SINGLE MOUNTING BRACKET is designed to provide support for Miller® SubArc welding equipment or other welding equipment. The mounting bracket is intended to provide support for the Miller Flux Hopper and wire drive system. This unit can either be mounted in a fixed or movable slide. The bracket is made of durable materials and is designed to withstand the harsh conditions of a welding environment. It is easy to install and can be mounted in a variety of configurations to meet your specific needs. The bracket also features a number of threaded holes that allow you to attach a variety of accessories, such as a flux hopper or wire drive.

Miller SINGLE MOUNTING BRACKET

OWNER’S MANUAL OM-274 405A

2015−12

For Single Mounting Bracket

1. Safety Symbol Definitions

DANGER! − Indicates a hazardous situation which, if not

avoided, will result in death or serious injury. The possible haz-

ards are shown in the adjoining symbols or explained in the text.

DANGER ! - Indique une situation dangereuse qui, si elle n’est

pas évitée, entraînera la mort ou des blessures graves. Les

éventuels risques sont représentés par les symboles joints ou

expliqués dans le texte.

Fsafe1 2013-10

Beware of electric shock from wiring. Disconnect input power

before installing this kit. Reinstall all panels and covers.

Attention aux décharges électriques au contact des câbles. Cou-

per l’alimentation électrique avant d’installer ce kit. Réinstaller

tous les panneaux et couvercles.

Fsafe7 2013-10

Indicates a hazardous situation which, if not avoided, could result

in death or serious injury. The possible hazards are shown in the

adjoining symbols or explained in the text.

Indique une situation dangereuse qui, si elle n’est pas évitée,

entraînera la mort ou des blessures graves. Les éventuels

risques sont représentés par les symboles joints ou expliqués

dans le texte.

Fsafe2 2013-10

Wear safety glasses with side shields.

Porter des lunettes de sécurité avec écrans latéraux.

Fsafe8 2013-10

NOTICE

Indicates statements not related to personal injury.

Signale des consignes non associées aux dommages corporels.

Indicates special instructions.

Fournit des instructions spéciales.

Fsafe3 2013-10

Have only trained and qualified persons install, operate, or ser-

vice this unit. Read the safety information at the beginning of

these instructions and in each section. Call your distributor if you

do not understand the directions. For WELDING SAFETY and

EMF information, read owner’s manual(s).

Ne confiez l’installation, l’exploitation ou l’entretien de cet appareil

qu’à des personnes compétentes et qualifiées. Lire les directives

de sécurité au début de ces instructions et dans chaque section.

Appeler votre distributeur si vous ne comprenez pas les

directives. Lire le(s) manuel(s) d’utilisateur pour des

renseignements sur la SÉCURITÉ DE SOUDAGE et les champs

électromagnétiques.

afe15 2013-10

CALIFORNIA PROPOSITION 65 WARNINGS

Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases,

cancer. (California Health & Safety Code Section 25249.5 et seq.) This product contains chemicals, including lead, known to the state of California to cause can-

cer, birth defects, or other reproductive harm. Wash hands after use.

Les équipements de soudage et de coupage produisent des fumées et des gaz qui contiennent des produits chimiques dont l’État de Californie reconnaît qu’ils

provoquent des malformations congénitales et, dans certains cas, des cancers. (Code de santé et de sécurité de Californie, chapitre 25249.5 et suivants) Ce

produit contient des produits chimiques, notamment du plomb, dont l’État de Californie reconnaît qu’ils provoquent des cancers, des malformations congénitales

ou d’autres problèmes de procréation. Se laver les mains après utilisation.

2. Description

The single mounting bracket is designed to provide support for Miller® SubArc welding equipment or other welding

equipment. The mounting bracket is intended to provide support for the Miller Flux Hopper and wire drive system. This

unit can either be mounted in a fixed or movable slide.

3. Specifications

Product Type Overall Dimensions Weight

Single Mounting Bracket 9.38 in. X 9.87 in. X 10.63 in.

(238 mm x 250 mm x 270 mm)

14 lbs

(6.4 kg)

4. Tools Needed

10 mm

1/4 in.

OM-274 405 Page 2

5. Dimensions

10.625 in.

(269 mm)

9.865 in.

(250 mm)

Top View

9.375 in.

(238 mm)

∅ .413 in. X 4 Thru

〈∅ 10.5 mm X 4 Thru)

Side view

Front View

4.33 in.

(110 mm)

5.750 in.

(146 mm)

1.969 in.

(50 mm)

273 921-A

6.000 in.

(152 mm)

OM-274 405 Page 3

6. Threaded Hole Layout

M10 x 1.5-6H 4 Places

1.966 in.

(50 mm)

4.311 in.

(110 mm)

. The single mounting bracket is provided with M10 x 25 socket head cap hardware for at-

taching the bracket to a fixed arm or movable slide. If desired, 3/8 - 16 x 1.00 in. hardware

may be used. In this case, the threaded hole should be adjusted accordingly.

274 404-A

Notes

OM-274 405 Page 4

7. Installation

! Turn Off wire feeder and weld-

ing power source power before

installing bracket.

1 Single Mounting Bracket

2 M10 Flat Washers

3 M10 Lock Washers

4 M10-1.5 x 25 SOC HD Cap

Screws

5 Fixed Arm

6 Manual Cross Slide

OPTION 1 − To mount the single

mounting bracket to a fixed arm, align

the four holes on the bracket with the

threaded holes on the fixed arm. Se-

cure bracket by tightening the four

M10 x 25 screws and hardware with a

10mm Allen wrench. Torque hardware

to 30 ± 2 in-lb (40 ± 3 N⋅M).

OPTION 2 − To mount the single

mounting bracket to a cross slide,

align the four holes on the bracket with

the M10 threaded holes on the cross

slide. Secure bracket by tightening the

four M10 x 25 screws and hardware

with a 10mm Allen wrench. Torque

hardware to 30 ± 2 in-lb (40 ± 3 N⋅M).

. When mounting the bracket to a

cross slide, be sure that the single

mounting bracket is mounted to a

vertical slide to allow for clear-

ance.

Option 1

Option 2

274 433-A

OM-274 405 Page 5

8. Mounting A Flux Hopper

! Turn Off flux hopper and welding

power source power before

mounting flux hopper.

. Secure single mounting bracket to

fixed arm, or cross slide (see Sec

tion 7) before mounting flux hopper

1 Flux Hopper

2 Insulator

3 Mounting Plate (Flux Hopper)

4 1/4 in. Insulating Shoulder Washer

5 1/4 in. Flat Washer

6 1/4 − 20 x .75 in. Screws (Sup-

plied w/Single Mounting Bracket)

7 Single Mounting Bracket

8 1/4 − 20 x 1.00 in. Screws

Before installing single mounting brack-

et, remove hardware, and discard flux

hopper mounting plate and the 1/4 - 20

x .75 in. screws. Retain insulator, and

other hardware. Place existing insulator

between flux hopper and single mount-

ing bracket. Align holes, and secure flux

hopper to single mounting bracket with

supplied 1/4 - 20 x 1.00 in. screws and

existing hardware. Torque screws to

7.5 ± 1 ft-lb (10 ± 1.5 N⋅M).

Threaded Holes

274 435-A

OM-274 405 Page 6

9. Mounting A Wire Drive

! Turn Off wire drive and welding

power source power before

mounting wire drive.

. Secure single mounting bracket to

fixed arm, or cross slide (see Sec-

tion 7) before mounting wire drive

motor.

1 Wire Drive Motor

2 1/4 - 20 Nuts

3 Single Mounting Bracket

4 Insulator

5 1/4 in. Insulating Spacer

6 1/4 in Insulating Washer

7 1/4 in. Flat Washer

8 1/4 in. Lock Washer

9 1/4 -20 Screws

Remove and discard the four 1/4 -20

nuts from the wire drive motor. Retain

the insulator, and other hardware.

Place existing insulator between wire

drive motor and single mounting

bracket. Align holes and secure wire

drive motor to single mounting bracket

with existing 1/4 - 20 screws, wash-

ers, insulating washers, and insulating

spacers. Torque screws to 23 ± 2 ft-lb

(31 ± 3 N⋅M).

Threaded

Holes

274 606-A

OM-274 405 Page 7

Notes

OM-274 405 Page 8

Notes

Miller SINGLE MOUNTING BRACKET Owner's manual

Brand: Miller

Model: SINGLE MOUNTING BRACKET

Type: Owner's manual

This manual is also suitable for

MF000000G

Miller SINGLE MOUNTING BRACKET

Download PDF

report

in other languages

français: Miller SINGLE MOUNTING BRACKET Le manuel du propriétaire

Miller SINGLE MOUNTING BRACKET Owner's manual

This manual is also suitable for

Miller SINGLE MOUNTING BRACKET Owner's manual

in other languages

Related papers

Other documents