Linear 309013 Installation guide

Linear
Brand
Linear
Model
309013
Type
Installation guide

Linear 309013

The Linear 309013 is a digital radio control system that allows you to operate your door opener from a distance. The system includes a receiver that mounts on your door opener and a transmitter that you can carry with you. The transmitter is self-contained, including a battery, and can be operated while being held in your hand or while mounted in your car.

The Linear 309013 is easy to install and use. Simply mount the receiver on your door opener and connect the wires from your wall button. Then, set the code on both the receiver and the transmitter to the same code. Once the code is set, you can check the operation by moving back a reasonable distance (30-50 feet) and pressing and holding the transmitter button for two seconds.

Linear 309013

The Linear 309013 is a digital radio control system that allows you to operate your door opener from a distance. The system includes a receiver that mounts on your door opener and a transmitter that you can carry with you. The transmitter is self-contained, including a battery, and can be operated while being held in your hand or while mounted in your car.

The Linear 309013 is easy to install and use. Simply mount the receiver on your door opener and connect the wires from your wall button. Then, set the code on both the receiver and the transmitter to the same code. Once the code is set, you can check the operation by moving back a reasonable distance (30-50 feet) and pressing and holding the transmitter button for two seconds.

DIGITAL RADIO CONTROLS
INSTALLATION INSTRUCTIONS
WARNING:
•
Disconnect power before any installation or repair.
•
Wear safety glasses.
WARRANTY
Your Linear Multi-Code
digital radio controls are warranted to the original purchaser
against defects in material or workmanship for a period of eighteen (18) months from the
date of purchase. This warranty will be considered void if damage is due to improper
installation, improper use, connection to improper power source, or if damage is due to
fire or lightning. Replacement of batteries is not covered by warranty.
RECEIVER INSTALLATION - MODEL 3090
Mount the receiver directly on the operator by sliding the receiver tabs underneath the
three terminal screws located on the operator. (See diagram below.) Remember to
reconnect your wall button wires.
TRANSMITTER - MODEL 3089
The transmitter is self-contained, including battery. It can be operated while being held in
your hand, or while mounted in your car. A clip is supplied so that the transmitter may be
mounted on your sun visor. When using the clip, slide it under the two straps on the back of
the transmitter until the small knob fits into the hole in the clip.
CAUTION:
Keep the clip flat when pushing it into position so that it doesn’t extend down into
the case and cause damage.
TRANSMITTER BATTERY REPLACEMENT
Replacement battery - 9 volt carbon zinc (non-alkaline). The battery can be checked or
changed by popping open the front lower half of the transmitter using a slot screwdriver.
Replace used battery and re-assemble the transmitter case.
SELECTING A CODE
Use a slot screwdriver to pop open the front lower half of the transmitter and the receiver
door for access to the code switches. Set both sets of switches to the code of your choice.
Be sure both are set to the exact same code, since a different setting of just one switch
will prevent operation. Once the code has been set, check the operation, and replace the
hatches.
OPERATIONAL CHECK
To check operation, move back a reasonable distance (30-50 feet), press and hold the
transmitter button for two seconds. If operation is unsatisfactory, the problem may be
isolated by:
1. Checking the door operator. If the door will not open when the wall button is pressed,
the problem is likely to be the operator. When the door opens by pressing the wall
button, but not the transmitter, then the problem is likely with the radio controls.
2. Reposition the antenna, and try it again.
3. Replace the transmitter battery.
Changes or Modifications not expressly approved by Linear Corporation could void the
user’s authority to operate the equipment.
When controls do not function after performing the above tests, they should be returned
to your dealer for repair or replacement. They may also be returned, postage prepaid,
directly to:
LINEAR CORPORATION
2055 CORTE DEL NOGAL, CARLSBAD, CA 92009
Copyright © 2000 Linear Corporation 217039 A
INSTR,INSTL,REC 310 CANADA
LINEAR P/N: 217039 A
INK: BLACK
MATERIAL: 20 LB. MEAD BOND
SIZE: 11.000" X 5.500"
SCALE: 1-1
SIDE 1 OF 2
™
®
  • Page 1 1

Linear 309013 Installation guide

Linear
Brand
Linear
Model
309013
Type
Installation guide

Linear 309013

The Linear 309013 is a digital radio control system that allows you to operate your door opener from a distance. The system includes a receiver that mounts on your door opener and a transmitter that you can carry with you. The transmitter is self-contained, including a battery, and can be operated while being held in your hand or while mounted in your car.

The Linear 309013 is easy to install and use. Simply mount the receiver on your door opener and connect the wires from your wall button. Then, set the code on both the receiver and the transmitter to the same code. Once the code is set, you can check the operation by moving back a reasonable distance (30-50 feet) and pressing and holding the transmitter button for two seconds.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents