GE GLDT690J__WW Technical Service Manual

Brand: GE

Model: GLDT690J__WW

Category: Dishwashers

Type: Technical Service Manual

This manual is also suitable for

GE Appliances

Louisville, Kentucky 40225

31-9248

GE Built-In Dishwasher

with Top Controls

GLDT690J_ _BB

GLDT690J_ _WW

GLDT696J_ _SS

Technical Service Guide

December 2015

GE Appliances

– 2 –

IMPORTANT SAFETY NOTICE

The information in this service guide is intended for use by

individuals possessing adequate backgrounds of electrical,

electronic, and mechanical experience. Any attempt to repair a

major appliance may result in personal injury and property

damage. The manufacturer or seller cannot be responsible for the

interpretation of this information, nor can it assume any liability in

connection with its use.

WARNING

To avoid personal injury, disconnect power before servicing

this product. If electrical power is required for diagnosis or test

purposes, disconnect the power immediately after performing the

necessary checks.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to

complete a path to ground are removed for service, they must be

returned to their original position and properly fastened.

GE Appliances

in any form without written permission from the General Electric Company.

Safety Information

– 3 –

Safety Information .......................................................................................................................................................................... 2

Table of Contents ............................................................................................................................................................................ 3

Safety Requirements ..................................................................................................................................................................... 4

Nomenclature ................................................................................................................................................................................... 5

Model Number ....................................................................................................................................................................... 5

Introduction ........................................................................................................................................................................................ 6

Weights & Dimensions .......................................................................................................................................................... 6

6SHFL¿FDWLRQV .................................................................................................................................................................................... 6

Control Features .............................................................................................................................................................................. 7

Throughout this manual, features and appearance may vary from your model. ................................7

About the dishwasher control panel .......................................................................................................................... 7

Overview of Cycles ......................................................................................................................................................................... 9

Component Locator Views .......................................................................................................................................................... 10

Front View ................................................................................................................................................................................... 10

Control Panel View .................................................................................................................................................................. 10

Interior View (Without Racks) ............................................................................................................................................. 11

Detergent/Rinse Module Compartment View ............................................................................................................ 11

Interior View of Basin (With Racks Removed) ............................................................................................................12

Bottom View (Looking Up) ................................................................................................................................................... 12

Right Side View (Insulation Removed) ............................................................................................................................ 12

Control Board Connector Locator View ................................................................................................................................ 13

Dishwasher Components ............................................................................................................................................................ 14

Troubleshooting .............................................................................................................................................................................. 29

Schematic ........................................................................................................................................................................................... 31

Warranty ............................................................................................................................................................................................. 32

Index ...................................................................................................................................................................................................... 33

Table of Contents

– 4 –

Prior to disassembly of the dishwasher to access components, GE

Factory Service technicians are REQUIRED to follow the Lockout /

Tagout (LOTO) 6 Step Process:

Safety Requirements

GE Factory Service Employees are required to use safety glasses with side shields, safety gloves and

steel toe shoes for all repairs.

Steel Toed Work Boot Electrically Rated Glove and

Dyneema® Cut Resistant

Glove Keeper

Dyneema®Cut Resistant

Glove

Prescription Safety Glasses

Safety Glasses must be ANSI

Z87.1-2003 compliant

Brazing Glasses

Cut Resistant Sleeve(s)

Step 1

Plan and Prepare

Step 4

Apply LOTO device and lock

Step 2

Shut down the appliance

Step 5

Control (discharge) stored energy

Step 3

Isolate the appliance

Step 6

“Try It” verify that the appliance is

locked out

Plano Type Safety Glasses

– 5 –

Model Number

The Mini Manual is located in a

plastic bag taped on the back

side of the toe kick.

Nomenclature

The nomenclature breaks down and explains what the letters and numbers mean in the model number.

Serial Number

7KH¿UVWWZRFKDUDFWHUVRIWKHserial number identify the month and year of manufacture. The letter

designating the year repeats every 12 years.

Example: TF123456S = October, 2015

A – JAN

D – FEB

F – MAR

G – APR

H – MAY

L – JUN

M – JUL

R – AUG

S – SEP

T – OCT

V – NOV

Z – DEC

2024 – Z

2023 – V

2022 – T

2021 – S

2020 – R

2019 – M

2018 – L

2017 – H

2016 – G

2015 – F

2014 – D

2013 – A

Product Type

GLD - GE Long Door

G L D T 6 9 0 J 0 0 B B

Top Control

Feature Package

Door

0 - Color Door

6 - Stainless Steel

Model Year Designator

J = 2015

Platform

4 - 6 = GE Tall Tub

Exterior Color

BB - Black

SS - Stainless Steel

WW - White

Engineering Digit

The Model Serial Tag is located on

the left side of the tub wall, inside the

door jamb.

Model Serial Tag

– 6 –

GE Built-In Dishwasher with Top Control

)HDWXUHVDQG%HQH¿WV

• ADA-compliant - Dishwasher design allows for simple operation and easy access

• 2015 Energy Star®TXDOL¿HG

• Two Step Start Compliant

• 2-digit countdown display with 1 to 24 hour delay start

• Side Mount ready

• Electronic Light Touch Control

• SanWash Cycle - Special cycle reduces 99.99% of harmful germs and bacteria

• Model GLDT690JWW - White on white

• Model GLDT690JBB - Black on black

• Model GLDT696JSS - Stainless steel

Introduction

Electrical Supply (Under Load) 60 Hz - 120 VAC + 10%

Supply Water Flow Rate 0XVW¿OOJDOORQFRQWDLQHULQVHFRQGV

Supply Water Temperature* 120°F to 150°F (49°C to 66°C)

Water Charge 0.85 gallons (3.2 liters). This water level can be

measured at 0.4" below the top surface of the

PDQXDO¿OWHU

Spray Arm Rotation 20 to 60 RPM

*Before starting dishwasher, run the water at the sink faucet until hot.

Weights & Dimensions

Approximate Shipping Weight 105 lb

Net Weight 85 lb

Overall Height 32 11/32 inches

Height w/Legs Extended 34 1/2 inches

Overall Depth 24 inches

Overall Width 24 inches

6SHFL¿FDWLRQV

– 7 –

Throughout this manual, features and appearance may vary from your model.

About the dishwasher control panel

Control Features

(Continued next page)

Start Dishwasher

Start/Reset: Press the Start/Reset button and close the door within 4 seconds to start

the cycle or begin the Delay Start countdown. The Start/Reset LED will light. The wash

F\FOHZLOOEHJLQDIWHUVHFRQGVDQGWKHQSXPSRXWIRUVHFRQGVSULRUWR¿OOLQJWKH

dishwasher with water. To activate the display, press any button with the door open.

Interrupt or Pause: To interrupt or pause a cycle, slowly open the door. Opening the

door will cause the wash cycle to pause. The dishwasher will beep every minute as a

reminder to close the door. To restart or resume the cycle, press Start/Reset, and close

the door within 4 seconds. If the door is not closed within 4 seconds, the Start/Reset

LED will start blinking and the dishwasher will beep once every minute to signal that the

cycle did not restart. If the Start/Reset LED is blinking, the dishwasher is waiting for input.

Cancel: To cancel a wash cycle, press and hold the Start/Reset button for 3 seconds with

the door open, and then close the door. The dishwasher will drain and the wash cycle

lights will turn off.

Wash Cycle Selections

Press the Select button to choose a wash cycle. The light above the cycle name will

display to indicate which cycle has been selected.

Delay Start Option

This option allows a delay the start of a wash cycle for up to 24 hours.

With the door open, turn the dishwasher ON by pressing the ON/OFF button; then press

the DELAY button to choose the number of hours wanted to delay the start of the wash

cycle. The hours will show in the display window.

NOTE: Press the Start/Reset button to cancel the Delay hours option before the start of the

cycle.

2 Digit Display

This display is used for DELAY START and cycle time countdown.

When a cycle is selected, the display is populated with the total number of minutes in

the cycle, until it reaches 99 minutes (Sanitize, Heavy and Normal cycles).

Status Indicators

SANITIZED: If the SANITIZE cycle is selected, the sanitized indicator light will be turned on

at the end of the cycle. If the NSF requirements for sanitization are not reached, the light

will not turn on.

CLEAN: The green light will display and a beep will sound to alert that the wash cycle is

complete. If the door is NOT opened, the beep will sound 4 times.

– 8 –

Explanation of Dishwasher State(s)

Dishwasher in Idle state

• Pressing any key will wake up the control. The control enters Standby mode.

• When power is applied to the dishwasher, the buzzer beeps once, and all of the display and indicators

are on for 1 second. After this, the unit will be in idle state.

• Press any button, the buzzer beeps once, the seven segment displays “- -”, other indicators are off, the

unit is in standby state.

Dishwasher in Standby state

• The control is awake and waiting for the Start/Reset to be pressed and the door closed within 4 seconds.

Dishwasher in Pause state (a.k.a.: Door open during the cycle)

• Start/Reset LED will blink 0.5 second on/0.5 second off. The buzzer will beep once every minute to alert

the user that the dishwasher is in the Pause state.

• To resume the cycle, the sequence described above in the Standby state will apply.

Dishwasher in Delay Start state (a.k.a.: Door open during the cycle)

• Start/Reset LED will blink 0.5 second on/0.5 second off. The buzzer will beep once every minute to alert

the user that the unit is in the Pause state.

• To resume the cycle, the sequence described above in the Standby state will apply.

Cancel Cycle

• The user must press and hold the Start/Reset button for 3 seconds in order to cancel a cycle.

• Upon cancelling a cycle, the unit will completely drain all water.

• At the completion of the drain step, the unit will enter the Idle state.

• After completing the drain step, the user may open the door, select a new cycle and/or options, and start

a new cycle according to the two-step requirements,

• If the user starts a new cycle, the drain step that resulted from cancelling the cycle will end and the new

cycle will begin.

• The drain step that normally occurs at the beginning of a new cycle will occur regardless of whether the

previous cycle had been cancelled or not.

If the dishwasher loses external power, or there is a blackout while a cycle is executing and it is in wash

stages, the dishwasher will resume in pump out mode and start at the beginning of the cycle in progress

once external power has been restored.

If the Blackout occurs during 'U\VWDJHWKHQWKHFRQWUROZLOOLQLWLDOL]HDWWKH¿UVWVWDJHRIGU\LQJDIWHUSRZHU

recovery.

CYCLES

WATER

(approx.

gallons)

TIME

(approx.

minutes)

CYCLE SEQUENCE

SANITIZE 4.8 137 Pre-Wash Pre-Wash Wash Rinse Rinse Dry

HEAVY 6.7 136 Pre-Wash Pre-Wash Pre-Wash Wash Wash Rinse Rinse Dry

NORMAL 3.2 150 Pre-Wash Wash Wash Rinse Dry

LIGHT 4.7 89 Pre-Wash Pre-Wash Wash Rinse Rinse Dry

GLASSES 3.8 87 Pre-Wash Wash Rinse Rinse Dry

SPEED 5.7 84 Pre-Wash Pre-Wash Pre-Wash Wash Rinse Rinse

RINSE 2.0 26 Pre-Wash Rinse

– 9 –

Overview of Cycles

• After pressing the START/RESET button, all LED's will light, the digital display will show 88, and the buzzer

will beep.

• The estimated cycle time will be displayed as a two-digit number. If the cycle time exceeds 99 minutes,

the seven segment display will show 2H. If the cycle time is less than or equal to 99 minutes, the actual

estimated cycle time is displayed.

• The control makes an End-of-Cycle Alert for 1 second every 2 minutes (with a maximum of 4 beeps) for

any mode (regardless of whether delay was selected or not) after the end of any cycle.

• Cancel/Change cycle: After a cycle has started, open the door and hold the Select button down for 3

seconds. After 3 seconds, the machine will beep and the display will select the next cycle to the right. If

left on any cycle with the door closed, the machine will drain and start that new cycle automatically.

• Delay Start: Select 1 to 24 hours as the amount of time to delay the start of the cycle. This will be

displayed as 1H, 2H, etc. The delay start display never shows minutes.

• When the door is closed, the display will turn off after 3 minutes regardless of a time delay. Opening the

GRRUZLOOWXUQWKHGLVSOD\EDFNRQ'XULQJWKHF\FOHUXQWKHVHOHFWHGF\FOH/('ZLOOÀDVKRQRII

• Two Step Start: The dishwasher may be programed with the door open only. Press the Cycle button

until the desired cycle is selected. Press Start and close the door within 4 seconds. Failure to close the

door within 4 seconds will require Start to be pressed again and closing the door within 4 seconds.

• Cycle Interruption: If a cycle is interrupted, Start/Reset must be pressed and the door closed within four

seconds. The control will wait 10 seconds before resuming the cycle. If the door is not closed within 4

VHFRQGVWKHF\FOHZLOOQRWUHVWDUW7KHF\FOHDQGVWDUW/('·VZLOOÀDVKDQGWKHEHHSHUZLOOVRXQGHYHU\

minutes until the cycle is restarted or canceled.

• There is no Demo mode.

NOTE: The door must be open for the keypads to operate. The keypad will appear to be inoperable with the

door in the latched position.

Sanitize Wash &\FOHGH¿QLWLRQ

The Sanitized LED will only be turned on at the end of the sanitize wash cycle if the following two conditions

are met during the cycle:

1. An internal calculation the board makes based on several heat factors (temperature + time).

2. 7KHZDWHUWHPSHUDWXUHLQWKH¿QDOULQVHLVJUHDWHUWKDQRUHTXDOWR)

7KHPD[LPXPWLPHIRUWKH¿QDOULQVHLQWKHVDQLWL]HZDVKF\FOHLVPLQXWHV,IERWKRIWKHDERYHFRQGLWLRQV

DUHPHWSULRUWRWKHPLQXWHOLPLWWKH¿QDOULQVHZLOOHQGLPPHGLDWHO\DQGERWKWKH6DQLWL]HGOLJKWDQG

&OHDQ/('ZLOOWXUQRQ,IHLWKHUFRQGLWLRQLVQRWPHWDWWKHHQGRIWKHPLQXWHOLPLWWKH¿QDOULQVHZLOOHQG

and the Sanitized light will not turn on.

SSD (Seven

Segment

Display)

– 10 –

Front View

Component Locator Views

Control Panel View

(Continued next page)

Control Panel

Door Panel

Insulation

Door Spring

Fill Funnel

Access Panel

Door Latch

Control Assembly

– 11 –

Detergent Module

Interior View (Without Racks)

Detergent/Rinse Module Compartment View

(Continued next page)

Static Dry Vent

Detergent/Rinse Module

Rinse Agent Outlet

Detergent Compartment

Compartment Lid

Sight Glass

Rinse Agent Cap

– 12 –

Interior View of Basin (With Racks Removed)

Bottom View (Looking Up)

127('UDLQKRVHLVVKRZQLQVKLSSLQJFRQ¿JXUDWLRQ

Front

Back

Right Side View (Insulation Removed)

Spray Arm

Filter Assembly

Heating Element

Clamp Nut

Micro-Filter

Fill Hose

Fill Funnel

Pressure

Switch

Pressure

Switch Hose

Water Inlet Valve

Sump

Drain Hose

Wash Pump Assembly

Thermistor

Drain Pump

Capacitor

Pressure

Switch

– 13 –

Control Board Connector Locator View

CN1 CN5 CN4

CN3

CN2P6

CN1: Door Switch CN4 and CN5: PCB user interface boards,

Power Control Board and two

UI Boards are replaced as an

assembly. Use all three boards

and new wire harnesses when

replacing any of these boards.

CN2: 120 VAC output:

Pin 1: Pressure switch

Pin 3: Water inlet valve

Pin 5: Detergent/rinse module

Pin 7: Drain pump

Pin 9: Motor pump

CN3: Thermistor P4:L1

P6: 120 VAC output to heater

– 14 –

Dishwasher Components

Control Panel

Control Panel Removal

1. Remove the outer door panel. (See Outer Door

Panel Removal.)

2. Remove 2 Phillips head screws from the door

latch.

Outer Door Panel

The outer door panel covers the door to the

dishwasher and must be removed to access the

control panel, detergent/rinse module, bottom door

seal, and the heating element.

Outer Door Panel Removal

1. To remove the outer door panel, remove 12

Phillips head screws.

2. Lower the door panel from the control panel.

Static Dry System

The static dry system operates through a vent,

located behind the left side door panel. The vent

allows hot air to exit the dishwasher tub and

gradually remove moisture that runs through the

tube and back into the tub.

Static Dry System Removal

1. Remove the control panel. (See Control Panel

Removal.)

2. Turn the static dry vent cover counterclockwise

and remove.

(Continued next page)

Cover

Vent

3. Tilt the control panel out to clear the lip and

remove.

127( The escutcheon console cover or top trim

with lettering is replaced using adhesive.

– 15 –

127(

• Inspect the cover for hard water/lime deposits

or debris, and clean if necessary.

• If the control panel gasket shows obvious signs

of wear or damage, replace the gasket.

• If the vent cover O-ring shows obvious signs of

wear or damage, replace the static dry vent.

Control Assembly

The control assembly consists of two UI's (User

Interface boards) and a PCB (power control board).

All three boards must be replaced as an assembly.

UI Assembly Removal

1. Disconnect the power supply to the dishwasher.

2. Remove the control panel (see Control Panel

Removal).

3. Remove the 2 Phillips head screws that attach

the PCB cover to the power board.

(Continued next page)

3. Pull the top of the vent out while lifting up to

clear the bottom of the dishwasher.

4. Disconnect the wire harnesses CN4 and CN5

from the PCB.

5. Cut the plastic tie that holds the wires to the

control panel.

6. Remove 3 Phillips head screws from the cycle

select UI.

Static Dry Vent

O-Ring

Disconnect

– 16 –

PCB Assembly Removal

1. Disconnect the power supply to the dishwasher.

2. Remove the control panel (see Control Panel

Removal).

3. Remove the 2 Phillips head screws that attach

the PCB cover to the PCB.

4. Disconnect the wire harnesses from the PCB.

5. Remove the 2 Phillips head screws that attach

the PCB assembly to the housing.

Door Switch Assembly

The door switch assembly consists of two switches

activated by a spring-loaded plunger. One door

switch connects or disconnects the line (hot) side of

120 VAC. The other switch connects or disconnects

the neutral side of 120 VAC.

:$51,1* Power remains applied to the controller

location at CN1, Pin 1 to 3, while the door is open

(unlatched).

When the door is in the closed position, the door

latch presses and holds down the switch plunger

on the door switch assembly. This action holds the

GRRU¿UPO\DJDLQVWWKHVHDODQGWKHQRUPDOO\RSHQ

contacts of the door switches are closed.

Door Switch Assembly Removal

1. Disconnect the power supply to the dishwasher.

2. Remove the control panel (see Control Panel

Removal).

3. Disconnect the 4 wiring harnesses from the door

switch.

4. Remove the 2 Phillips head screws that hold the

door switch assembly to the control panel.

7. Remove 2 Phillips head screws from the display

UI.

Disconnect

– 17 –

Detergent/Rinse Module

The control panel must be removed to access

the detergent/rinse module (see Control Panel

Removal).

The detergent/rinse module is connected by 2 wires

and held in place by 6 Phillips head screws and 2

brackets.

The detergent/rinse module operates on 120 VAC

and has an approximate resistance value of 2k

ohms

The detergent/rinse module automatically

dispenses both the detergent and the rinse agent at

the appropriate times. The module is activated twice

during a wash cycle. Detergent is dispensed at the

beginning of the main wash cycle and rinse agent at

WKHEHJLQQLQJRIWKH¿QDOULQVH

Operation of the detergent/rinse module can be

checked by using the service mode (see Service

Mode).

7KH¿UVWWLPHWKHPRGXOHLVDFWLYDWHG the lever

slides up the right-hand path of the connecting rod

(1). This action releases the detergent cover.

When deactivated, the lever returns down the left-

hand path and comes to rest under the notch (2) in

the center of the connecting rod.

At the second activation, the lever lifts the

connecting rod by the notch. This action lifts the

rinse dispenser plunger (3) and releases the rinse

agent. When deactivated, the lever returns to its

original starting position.

127(Make sure the rubber seal is retained in the

recessed groove before reinstalling the module to

the door assembly.

Bracket

Disconnect

Seal

– 18 –

Inner Door Panel

Inner Door Panel Removal

1. Disconnect power.

2. Remove the control panel (see Control Panel

Removal).

3. Remove the detergent/rinse module (see

Detergent/Rinse Module).

4. Remove the 4 Phillips head screws (two on each

side) that attach the inner door panel to the

bottom door bracket.

127(When installing the inner door, place a pair

of pliers into the bottom door bracket to prevent it

from closing.

Bottom Door Seal

The bottom door seal prevents water leakage by

sealing between the bottom of the door and the

tub. It is not replaced as a separate part on this

dishwasher. It is replaced as part of the inner door

panel (see Inner Door Panel).

– 19 –

Tub Gasket and Trim

The dishwasher tub seal prevents water leakage.

7KHVHDOLV¿WWHGLQDVHDOFKDQQHOWKDWOLQHVWKHULP

of the dishwasher tub.

Tub Seal and Trim Removal

1. Open the dishwasher door.

2. Remove the dishwasher tub seal by grasping

one end of the seal to peel it away from the seal

channel.

4. Reverse the above procedures to install.

NOTE: When installing the tub seal, make sure it is

VHDWHGSURSHUO\LQWKHVHDOFKDQQHO5XQD¿QJHU

over the seal to make sure it is smooth and even for

a proper seal. A correctly installed gasket will have

both ends of the gasket equally distant from the

bottom of the tub.

3. Remove the dishwasher trim by pulling the trim

straight off the lip of the tub.

Heating Element

The heating element maintains water temperature

during the wash and rinse cycles and heats the air

during the static dry cycle.

The heater has an approximate resistance value of

21 ohms.

Operation of the heating element can be checked

by using the service mode (see Service Mode). Allow

one or two minutes before opening the dishwasher

door and note if heat is present.

Heating Element Removal

1. Remove the outer door panel (see Outer Door

Panel Removal).

2. Remove the bottom rack.

3. Remove the 2 Phillips head screws, washers,

and the access panel.

4. Remove the 2 Phillips head screws and lower the

water valve from the front brace.

5. Remove the 2 Phillips head screws and lower the

junction box from the front brace.

(Continued next page)

6. Remove the 6 Phillips head screws and the front

brace from the dishwasher.

Seal Channel

Tub Seal

Trim

Tub Lip

Front Brace

Water Valve

Junction Box

– 20 –

7. Locate the wires leading to the heating element

terminals and pull down the 2 nylon terminal

covers.

8. Disconnect the 2 wires from the heating

element.

9. Remove the outer 8 mm nut that attaches the

ground wire to the element mounting bolt.

11. Lift the right side of the element and release it

from the 2 retainers.

10. Remove the inner 8 mm nut, washer, and spacer

that attaches the element to the bottom of the

tub.

Nylon Terminal Covers

Heater Wire Heater Wire

Outer Nut

Ground Wire

Spacer

Inner Nut

Washer

Page is loading ...

GE GLDT690J__WW Technical Service Manual

Brand: GE

Model: GLDT690J__WW

Category: Dishwashers

Type: Technical Service Manual

This manual is also suitable for

Download PDF

report

GE GLDT690J__WW Technical Service Manual

This manual is also suitable for

GE GLDT690J__WW Technical Service Manual

Related papers

Other documents