Real Fyre G8E Split Valley Oak Log Operating instructions
- Type
- Operating instructions
This manual is also suitable for
Real Fyre G8E Split Valley Oak Log is a realistic-looking gas log set that can be used to add warmth and ambiance to your home. It features a unique split valley oak design that is sure to impress your guests. The log set is made of durable materials that are designed to withstand the heat of a fire, and it comes with a one-year warranty.
Real Fyre G8E Split Valley Oak Log is a realistic-looking gas log set that can be used to add warmth and ambiance to your home. It features a unique split valley oak design that is sure to impress your guests. The log set is made of durable materials that are designed to withstand the heat of a fire, and it comes with a one-year warranty.
1
CAUTION...............WARNING...............IMPORTANT
USE ONLY A PETERSON REAL FYRE G9 BURNER WITH THIS REAL FYRE LOG SET.
Important: Adequate spacing between the
logs is NECESSARY and MUST be
maintained. If carbon build up (sooting)
exists, correct log placement before
sooting becomes worse. If any sooting
occurs outside of the rebox (i.e. on
the walls), turn o unit immediately
and contact a qualied professional
service technician.
WARNING: Use ONLY a Peterson Real Fyre
G9 burner with this Real Fyre gas log
set. Failure to do so may result in
property damage or personal injury,
and will void listings, certications,
and invalidate claims made to RHP.
Contact your local Real Fyre dealer if you
need more information.
This instruction contains log set placement for these Real Fyre logs. You must position and maintain the log
layout as shown here to ensure proper operation of the burner system. Incorrect log installation could cause
ame impingement and improper combustion, resulting in soot and/or excessive by-products of combustion.
DO NOT add any additional embers for this installation. Any additional embers will cause unsafe operation.
Use these logs only with a Peterson G9 burner system.
If you experience an accumulation of black carbon (soot) on your logs it is an indication of incomplete
combustion and you must correct the log placement as instructed in this manual. If signicant sooting
continues, stop using this gas log set.
Please read these instructions completely and carefully.
This product is only warranted when used as part of a
Robert H. Peterson Co. unvented burner system.
LOG SET IMPORTANT INFORMATION
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
L-F2-137
REV 0 - A - 2303230800
CAUTION...............WARNING...............IMPORTANT
USE ONLY A PETERSON REAL FYRE G9 BURNER WITH THIS REAL FYRE LOG SET.
Important: Adequate spacing between the
logs is NECESSARY and MUST be
maintained. If carbon build up (sooting)
exists, correct log placement before
sooting becomes worse. If any sooting
occurs outside of the rebox (i.e. on
the walls), turn o unit immediately
and contact a qualied professional
service technician.
WARNING: Use ONLY a Peterson Real Fyre
G9 burner with this Real Fyre gas log
set. Failure to do so may result in
property damage or personal injury,
and will void listings, certications,
and invalidate claims made to RHP.
Contact your local Real Fyre dealer if you
need more information.
This instruction contains log set placement for these Real Fyre logs. You must position and maintain the log
layout as shown here to ensure proper operation of the burner system. Incorrect log installation could cause
ame impingement and improper combustion, resulting in soot and/or excessive by-products of combustion.
DO NOT add any additional embers for this installation. Any additional embers will cause unsafe operation.
Use these logs only with a Peterson G9 burner system.
If you experience an accumulation of black carbon (soot) on your logs it is an indication of incomplete
combustion and you must correct the log placement as instructed in this manual. If signicant sooting
continues, stop using this gas log set.
Please read these instructions completely and carefully.
This product is only warranted when used as part of a
Robert H. Peterson Co. unvented burner system.
LOG SET IMPORTANT INFORMATION
MEADOW OAK LOG PLACEMENT INSTRUCTIONS
M9-24 shown
2
Failure to use a Peterson G9 burner may result in a DANGEROUS
situation and in property damage, personal injury or even death, will void
listings and certications, and will void any insurance coverage by R.H.
Peterson Co. or our insurers.
CAUTION: Burn hazard! Logs will remain hot for some time after use.
If you need to reposition any log to maintain the proper layout,
use heat resistant gloves or allow logs adequate time to cool
before handling.
WARNING: This gas log set is for use with an R.H. Peterson Co. G9
burner (and parts) ONLY.
L-F2-137
REV 0 - A - 2303230800
3
MEADOW OAK LOG PLACEMENT INSTRUCTIONS (20", 24", & 30" MODELS)
III
I II
IV
M9-(20,24,30) PARTS LIST
M9-24 log set shown
1
2
4
3
5
6
20" & 24" - ML9-17BR
30" - ML9-20BR
20" - ML9-20BF
24" - ML9-24BF
30" - ML9-30BF
ML9-11TL
Place the rear log (log #1) as shown. Slide it forward on the
burner, against the main burner bracket. ENSURE THE
LOG RESTS FLAT ON THE BURNER, AND THAT THE
BURNER BRACKET ALIGNS WITH THE GROOVES
FOUND ON THE FACE OF THE LOG.
2
Place the front log (log #2) as shown. The underside of
the log has two tabs that insert into the holes found on the
burner. The cutouts found on the underside of the log will
align over the grate ngers. ENSURE THE LOG RESTS
FLAT ON THE BURNER/GRATE.
Ensure the rear and front logs are snug up against the main
burner bracket.
Place the left top log (log #3) as shown. The log should lock
in place over the logs below.
ML9-11TR
ML9-12TY
ML9-11TY
1
Logs snug against bracket
The underside of the bottom logs have cutouts and tabs that align over the burner. THE BOTTOM LOGS
MUST BE FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to
interlock in place.
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
3
Align
notches
with
bracket
Align tabs
with holes
4
After setting the logs into position as described above, ensure each is properly and rmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the ames will not strike any portion of the logs. Periodically check the positioning of all logs
to ensure proper log placement and stability. If any ame is striking the logs, recheck log placement.
Adjust to conform with instructions. There should be no ame impingement on the logs.
MEADOW OAK LOG PLACEMENT INSTRUCTIONS (20", 24", & 30" MODELS) (CONT.)
Place the right top log (log #4) as shown. The log
should lock in place over the logs below.
VVI
Place the center left top log (log #5) as shown.
The log should lock in place over the logs below.
5
Place the center right top log (log #6) as shown.
The log should lock in place over the logs below.
VII
4
6
-
1
-
2
-
3
-
4
Real Fyre G8E Split Valley Oak Log Operating instructions
- Type
- Operating instructions
- This manual is also suitable for
Real Fyre G8E Split Valley Oak Log is a realistic-looking gas log set that can be used to add warmth and ambiance to your home. It features a unique split valley oak design that is sure to impress your guests. The log set is made of durable materials that are designed to withstand the heat of a fire, and it comes with a one-year warranty.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI