Atlona AT-HDVS-CAM-CMNT PTZ Ceiling Mount Kit Installation guide
- Category
- Camera mounting accessories
- Type
- Installation guide
1
Installation Guide
AT-HDVS-CAM-CMNT
PTZ Ceiling Mount Kit
AT-HDVS-CAM-CMNT
The Atlona AT-HDVS-CAM-CMNT is a ceiling mount kit for the AT-HDVS-CAM, AT-HDVS-
CAM-HDMI, and AT-HDVS-CAM-HDBT PTZ cameras. It includes all necessary hardware to
enable a secure, ush installation onto a ceiling surface. This accessory is ideal for classrooms
and meeting rooms requiring an overhead or rear-oriented camera, for capturing a presenter or
lecturer at the front of the room
Package Contents (Legacy)
Package Contents
1 x AT-HDVS-CAM-CMNT
4 x PA3X30 self-tapping screws
4 x PM3X6 screws
4 x screw stoppers
1 x 1/4 20UNC screw
1 x Installation Guide
1 x AT-HDVS-CAM-CMNT
4 x PA3X30 self-tapping screws
1 x 1/4 20UNC screw
1 x Installation Guide
2
Installation Guide
AT-HDVS-CAM-CMNT
A
A
1/4"20UNC
CAMERA BOTTOM
A
CEILING / SURFACE
B
B
B
1
A
A
1/4"20UNC
CAMERA BOTTOM
A
CEILING / SURFACE
B
B
B
1
A
A
1/4"20UNC
CAMERA BOTTOM
A
CEILING / SURFACE
B
B
B
1
A
A
1/4"20UNC
CAMERA BOTTOM
A
CEILING / SURFACE
B
B
B
1
1. Position part A at the desired position on the ceiling / surface. Attach part A to the ceiling /
surface by positioning screws (not provided) through the arc-shaped holes (1), as required.
2. Attach part B to the bottom of the AT-HDVS-CAM using the included 1/4” 20UNC screw.
3. Attach part A to part B, as shown below. Make sure the swivel joint on part A is positioned
in the swivel notch on part B. Attach each of the four included screws, as shown, to secure
both parts of the mounting xture.
4. The completed assembly.
Installation
1
3
1
4
1
2
1
1
3
Installation Guide
AT-HDVS-CAM-CMNT
1. Install the 4 screw stoppers in the ceiling.
2. Connect the upper ceiling covering plate to the screw stoppers using the PA3X30 self-
tapping screws.
3. Connect the lower ceiling covering plate to the bottom of the HDVS-CAM/-HDMI/-HDBT
using the 1/4 20UNC screw.
4. Mount the lower ceiling covering plate to the upper ceiling plate using 3 PM3X6 bolts.
NOTE: The camera picture will need to be inverted for video to be viewed
correctly. View the AT-HDVS-CAM/-HDMI/-HDBT manual for instructions on how
to invert video.
Installation - Legacy Mounts
ON KE
1 2
ON KE
1 2
To install the AT-HDVS-CAM, AT-HDVS-CAM-HDMI, or AT-HDVS-CAM-HDBT onto a ceiling, the
following is needed: 4 PA3X30 self-tapping screws, 4 PM3X6 screws, 4 screw stoppers, 1 1/4
20UNC screw, AT-HDVS-CAM-CMNT, and the AT-HDVS-CAM/-HDMI/-HDBT.
4
Installation Guide
AT-HDVS-CAM-CMNT
© 2021 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Toll free US International
atlona.com • 877.536.3976 • 41.43.508.4321
Version 2 25183-R2
-
1
-
2
-
3
-
4
Atlona AT-HDVS-CAM-CMNT PTZ Ceiling Mount Kit Installation guide
- Category
- Camera mounting accessories
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI