READY
Page 1 of 8
ASSEMBLY INSTRUCTIONS
TWIN
JCB M6 X 60mm 2- pcs Barrel Nut 2- pcs
BA
DE
C
J
F
G
K
JCB M6 X 25mm - 10 pcs
Wood dowel - 10 pcs
Spare - 1 pc
Spare - 1 pc
Wood screw 5/8” - 9 pcs
Wood screw ” - pcs18
Spare - 1 pc
Spare - 1 pc
Metal pull - 4 pcs
Metal pull screw 25mm - 8 pcs
Allen wrench - 1 pc
Spare - 1 pc
Spare - 1 pc
PO :
NANTUCKET MURPHY BED
WITH CHARGING STATION
Before assembling your Murphy bed, please read through these
instructions carefully and familiarize yourself with the different parts.
ATTENTION! If you receive a damaged or defective item,
please contact afifurnishings at [email protected] or 1-800-955-3726
Adult assembly
Phillips screwdriver
Customer supplied
HARDWARE
NOTE: WE INCLUDE SPARE HARDWARE IN CASE DAMAGE OCCURS DURING ASSEMBLY.
HWasher - 24pcs
Adjust quantity as needed. ITriangle Bracket - 2 pcs
02
01
03
04
05
06
07
08
09
TOP PANEL
HARDWARE
LEFT SIDE PANEL
RIGHT SIDE PANEL
DOOR
BACK PANEL
MIDDLE BACK RAIL
DRAWER BASE
FOLDING MATTRESS
01
02
03
04
05
08
09
08
04
03
06
06
Page 2 of 8
1 BOX
1 BOX
1 BOX
A
A
A
A
A
A
A
AA
A
Wooden dowel
A
PARTS LIST
NANTUCKET MURPHY BED
WITH CHARGING STATION
STEP 1
Insert all wooden dowels (A) into the locator holes on (03)(04) and (0 ) as shown below.8
Adult assembly
07
TWIN
Adult assembly
Page 3 of 8
08
03
04
06
B
B
B
B
B
B
JCB M6 X 25mm
Allen wrench
B
K
Adult assembly
STEP 2
Attach left and right side panels (03) and (04) to the drawer base (0 ) as shown below.
Using JCB (B) tighten with Allen wrench (K)
8
NANTUCKET MURPHY BED
WITH CHARGING STATION
STEP 3
Guide the back panel (0 ) in carefully so that it won’t jump out of its grooves. Be sure
it fits fully into its groove at the .
6
top panel base
TWIN
NANTUCKET MURPHY BED
WITH CHARGING STATION
STEP 4
JCB M6 X mm60
Barrel Nut
Allen wrench
D
E
K
Adult assembly
Guide the (0 ) in carefully so that it won’t jump out of its grooves.middle back rail 7
Using JCB (D) and barrel nut (E). Tighten with Allen wrench ( ).K
07
06 02
07
E
B
B
B
B
B
E
E
D
D
STEP 5
Guide the back panel (0 ) in carefully so that it won’t jump out of its grooves. Be sure
it fits fully into its groove at the .
6
middle back rail Attach top panel (02) to cabinet
assembly as shown below. Use JCB (B). Tighten with Allen wrench ( ).K
JCB M6 X 25mm
Allen wrench
B
K
Adult assembly
BOTTOM VIEW
Page 4 of 8
TWIN
Page 5 of 8
05
G
G
G
F
F
FF
G
STEP 6 Install metal pull (F) to the locator holes on (05) as shown below. Using metal
pull screw (G) and washers (H) tighten with Phillips screwdriver (customer supplied).
Metal pull
Metal pull screw
F
G
Phillips screwdriver
Customer supplied
Adult assembly
Washer
Adjust quantity
as needed
H
NANTUCKET MURPHY BED
WITH CHARGING STATION
STEP 7
TWIN
Back view
G
H
H
HH
G
G
G
C
C
C
C
Lay the door down flat as shown below. Attach door hinge to drawer base using wood
screw (C) and tighten with Phillips screwdriver (customer supplied ).
Note: Be sure to align door with side panels in this step.
Wood screw 5/8”
C
Phillips screwdriver
Customer supplied
Adult assembly
Page 6 of 8
1
2
STEP 8
NANTUCKET MURPHY BED
WITH CHARGING STATION
STEP 9
Lift the door and fold as shown below.
Lift the door and latch to side panel as
shown below.
TWIN
Push the door closed and latch both sides as shown below.
Lock
Adult assembly
Page 7 of 8
I
I
J
J
STEP 10
NANTUCKET MURPHY BED
WITH CHARGING STATION
STEP 11
Attach triangle bracket (I) to the back of cabinet as shown below. Use wood screw (J)
tighten with Phillips head screwdriver. (customer supplied).
Triangle bracket
Wood Screw 1”
I
J
Adult assembly
TWIN
Pull the drawer out fully. Unlatch the door and open, folding down as shown.
Open
Adult assembly
Page 8 of 8
Congratulations!
09
09
STEP 12
NANTUCKET MURPHY BED
Adult assembly
Adult assembly
WITH CHARGING STATION
STEP 13 Open top panel and push drawer base in as shown below.
Install folding mattress (09) to the bed.
Your Murphy bed is now ready for use.
We recommend that you recheck that all screws are tight,
and that all parts are secure before use to ensure lasting Safety.
TWIN
/