Installation Guide
Side-by-Side combinations
20230410 7085386 - 00
SBS
Contents
1 General safety instructions.................................. 2
2 Transporting the appliance................................... 2
3 Installing the appliance........................................ 2
4 External dimensions of the appliance.................. 4
5 Side-by-side assembly.......................................... 4
6 Disposing of packaging......................................... 6
The manufacturer works constantly on the further develop‐
ment of all the types and models. Therefore please under‐
stand that we have to reserve the right to make design,
equipment and technical modifications.
To get to know all the benefits of your new appliance,
please read the information contained in these instructions
carefully.
The instructions apply to several models. Differences may
occur. Text relating only to specific appliances is marked
with an asterisk (*).
Instructions are marked with a , and results are marked
with a .
1 General safety instructions
-Please keep this assembly manual in a safe
place so you can refer back to it at any
time.
-If you pass the appliance on, please hand
this assembly manual to the next user.
-Read this assembly manual carefully before
installation and use to ensure safe and
correct use of the appliance. Follow
the instructions, safety instructions and
warning messages included at all times.
They are important for ensuring you can
operate and install the appliance safely and
without any problems.
-First read the general safety instructions in
the “General safety instructions” section of
the operating instructions, which accom‐
pany these installation instructions, and
follow them. If you cannot find the
operating instructions, you can down‐
load the operating instructions from the
internet by entering the service number
at home.liebherr.com/fridge-manuals. The
service number can be found on the serial
tag:
-Observe the warning messages and other
detailed information in the other sections
when installing the appliance:
DANGER identifies a situation involving
direct danger which, if not obvi‐
ated, may result in death or severe
bodily injury.
WARNING identifies a dangerous situation
which, if not obviated, may result
in death or severe bodily injury.
CAUTION identifies a dangerous situation
which, if not obviated, may result
in minor or medium bodily injury.
NOTICE identifies a dangerous situation
which, if not obviated, may result
in damage to property.
Note identifies useful instructions and
tips.
2 Transporting the appliance
uTransport the appliance only in suitable packaging.
uTransport the appliance upright.
uDo not transport the appliance on your own.
3 Installing the appliance
CAUTION
Risk of injury and damage!
The door may strike the wall and be damaged as a result.
In the case of glass doors, the damaged glass may cause
injuries!
uProtect the glass door from striking against the wall. Fit a
door stop, e.g. one made of felt, to the wall.
uA limiter restricting door opening to 90° can be ordered
from the aftersales service.
WARNING
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause
short circuits.
uThe appliance is designed for use in enclosed areas. Do
not operate the appliance outdoors or in areas where it is
exposed to splash water or damp conditions.
WARNING
Danger of fire due to incorrect positioning!
If the mains cable or plug touches the back of the appli‐
ance, the vibration can damage the mains cable or the plug
resulting in a short circuit.
uMake sure the mains cable is not trapped under the appli‐
ance when you position the appliance.
uStand the appliance so that it is not touched by connec‐
tors or main cables.
uDo not connect any appliances to sockets in the area of
the back of the appliance.
uDo not place and operate multi-sockets/power distribu‐
tors and other electronic devices (such as halogen trans‐
formers) at the back of the appliances.
General safety instructions
2 * Depending on model and options
WARNING
Leaking coolant and oil!
Fire. The coolant contained in the appliance is eco-friendly,
but also flammable. The oil contained in the appliance
is flammable. Escaping coolant and oil can ignite if the
concentration is high enough and in contact with an
external heat source.
uDo not damage the pipelines of the coolant circuit and
the compressor.
WARNING
Fire hazard and danger of damage!
uDo not place appliances emitting heat e.g. microwaves,
toasters etc. on the appliance!
NOTICE
Covered vents!
Damage. Appliance can overheat, which can reduce the
service life of various parts of the appliance and lead to
operational impairments.
uAlways make sure there is good ventilation.
uAlways keep vents or ventilation grids in the appliance
housing and in the kitchen furniture (fully integrated
appliance) unobstructed.
uAlways keep the fan air vents unobstructed.
If your appliance is not a side-by-side (SBS) appliance:
qBefore you connect the appliance, report any damage
immediately to the delivery company.
qThe floor of the installation site must be horizontal and
even.
qDo not install the appliance in direct sunlight, next to an
oven, radiator or similar.
qThe best place for installation is a dry and well ventilated
room.*
qInstall the appliance with the rear panel up against the
wall.
qOnly ever move the appliance when it is empty.
qThe surface supporting the appliance must be at the
same level as the surrounding floor.
qDo not install the appliance on your own.
qThe more coolant there is in the appliance, the larger
the room in which the appliance is installed must be. If
the room is too small, any leak may create a flammable
mixture of gas and air. For each 8 g of coolant the instal‐
lation space must be at least 1 m3. Information on the
coolant is on the model plate inside the appliance.
uDetach the connecting cable from the rear of the appli‐
ance, removing the cable holder at the same time
because otherwise there will be vibratory noise!
uRemove the protective film from the outside of the appli‐
ance.
NOTICE
The stainless steel doors are provided with a high-quality
surface coating and must not be treated using the accom‐
panying care product.
Otherwise the surface coating will be affected.
uWipe the coated door surfaces using a soft, clean cloth
only.
uApply a stainless steel cleaner only to the stainless steel
side walls evenly, wiping with the grain. Subsequent
cleaning becomes easier as a result.
uWipe side walls with a paint finish using a soft, clean
cloth only.
NOTICE
The stainless steel doors are finished with a high quality
surface coating and must not be treated with the enclosed
care product,
as otherwise the surface coating will be damaged.
uPlease only use a soft clean cloth to wipe the coated
door surfaces.
uOnly use a stainless steel care product on the stainless
steel side walls, applying it evenly in the direction of
polishing. Subsequent cleaning will then be easier.
uUse only a soft clean cloth to wipe side walls and door
surfaces with a paint finish.
NOTICE
Risk of damage from stainless steel care products!
The stainless steel doors and stainless steel side walls are
finished with a high-quality surface coating.
Stainless steel care products will damage the surfaces.
uUse only a soft, clean cloth to wipe the coated door
surfaces and side walls.
uRemove the protective film from the decorative trims.
uRemove the protective film from the decorative trims and
drawer fronts.
uRemove all transit supports.
uDispose of packaging material (see 6 Disposing of pack‐
aging) .
CAUTION
Risk of injury or damage from the appliance tipping or the
door falling open!
If the additional adjustable foot on the base support is not
correctly positioned on the floor, there is a risk of the door
falling open or the appliance tipping. This can lead to injury
or property damage.
uUnscrew the additional adjustable foot on the support
until it reaches the floor.
uThen turn it another 90°.
uAlign the appliance so that it
stands firmly and on a level
by applying the accompa‐
nying spanner to the adjust‐
able-height feet (A) and
using a spirit level.
uThen support the door:
Extend the adjustable foot
at the turn hinge (B) until it
rests on the floor and then
make a further 90° turn.
uThen support the door: Use saddle wrench SW10 to
unscrew the base on mounting block (B) until it makes
contact with the ground, then continue turning it for a
further 90°.
When a Side-by-Side appliance (S…) is fitted together
with a second appliance (as a SBS combination):
uProceed according to the Side-by-Side combined fridge-
freezer installation instructions. (Accessories bag of the
SBS freezer/appliance with freezer compartment)
Note
uClean the appliance .
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
Installing the appliance
* Depending on model and options 3
uAlways see to good ventilation at the installation site.
4 External dimensions of the
appliance
Appliance description A (mm) B(mm)
SBSes 7155 1852 630
SBSes 7165 1852 630
SBS(esf) 7212 1852 630x
SBS(esf) 7222 1852 630x
SBS(es) 7252 1852 630
SBS(es/bs) 7253 1852 630
SBS 7262 1852 630
SBS(es/bs) 7263 1852 630
SBS(ef) 7343 1852 630
SBS(es/bs) 7353 1852 630
SBS(ef) 7242 1852 623x
Fig. 1
x For appliances supplied with wall spacers, the measure‐
ment increases by 35 mm (see 3 Installing the appliance) .
5 Side-by-side assembly
All the assembly components are supplied with the appli‐
ance.
Fig. 2
Fig. 3
Ensure that the following tools are to hand:
qSpirit level
qPower screwdriver
qScrewdriver Torx® 25
qOpen-ended spanner size 10 (included in supply package)
Information for moving the combined appliance:
qBefore assembling the appliances, site them as closely
as possible to the final position.
qWhen moving the appliances, always take hold of them
at the outer front corners. On no account should you
push with your knee against the side walls or door.
qThe combined appliance is easiest to shift diagonally by
moving the left and right corner alternately.
Once the combined appliance is exactly in front of the
aperture, push it straight in.
qIf the combined appliance
has to be pulled out of
the aperture again, take
hold of it in the lower third
area and pull it straight
forwards.
NOTICE
Risk of damage when moving the combined SBS appliance!
The combined SBS appliance is heavy once assembled. The
appliance may be dented by improper movement.
uObserve the information given on moving the appliance
(see above).
uRemove all protective film from the outside of the
housing.
On the front of the appliance:
External dimensions of the appliance
4 * Depending on model and options
Fig. 4
uIf necessary, completely retract the height-adjustable
feet Fig. 4 (A) at the front of both appliances so that they
are not touching the floor.
uPlace the caps Fig. 4 (1) onto the four front height-adjust‐
able feet.
uPush both appliances together up to approx. 10 mm apart
so that they stand flush at the front.
Fig. 5
uUnclip and remove the covers Fig. 5 (2).
The joining plate automatically aligns the height of the
appliances. If one appliance is slightly higher than the other,
start with that appliance.
uPut the joining plate Fig. 5 (3) in place and fix it loosely to
one appliance with two screws Fig. 5 (4).
uMove the joining plate sideways so that the centre bar of
the plate lies on the side wall of the appliance. Tighten
the screws.
uNow screw the joining plate to the other appliance. As
you do this, shift the appliances together or apart slightly
as necessary.
Fig. 6
uIf the appliance is fitted with the pre-mounted screw
Fig. 6 (7): Undo the screw.
The joining plate automatically aligns the depth of the appli‐
ances. If one appliance is further forward than the other,
start with that appliance. Otherwise start with the appliance
on the left.
uFix the joining plate Fig. 6 (5) loosely to one appliance
with two screws Fig. 6 (6).
uMove the joining plate sideways so that the centre bar of
the plate lies on the side wall of the appliance. Tighten
the screws.
uNow screw the joining plate to the other appliance. As
you do this, shift the appliances together or apart slightly
as necessary.
On the rear of the appliance:
Fig. 7
uInsert the joining clamp Fig. 7 (8) at the top of the centre
side walls.
uInsert the joining angle Fig. 7 (9) into the recess at the
bottom.
uIf the joining angle is too loose, fix it with a screw
Fig. 7 (10).
Note
uTo avoid vibration noise, ensure neither the clamps nor
the screws are in contact with the tubes on the rear of
the appliance!
On the front of the appliance:
Fig. 8
NOTICE
Risk of damage to the castor bases!
uWhen aligning the appliance by the back adjustable feet,
do not use a cordless screwdriver, as this will either
damage the height adjustment mechanism or possibly
loosen the adjusting rod. Adjust the feet by hand.
You can adjust the front height-adjustable feet with the
open-ended spanner Fig. 8 (11) included in the supply
package, and the rear height-adjustable feet* with a Torx®
25 screwdriver.
uRetract the centre height-adjustable feet Fig. 4 (C) so
they are not in contact with the floor.
uLevel the combination using the outer height-adjustable
feet Fig. 4 (B).
Side-by-side assembly
* Depending on model and options 5
Fig. 9
Before fitting the cover strip Fig. 9 (12), press the two bars
together along the whole length. That makes it easier to
insert the strip into the gap. Use a soft cloth to press
the strip into place to avoid making dents in the surface.
Carefully press the strip into the gap, keeping it straight, to
achieve an optimal joint.
uOn the front, press the long cover strip Fig. 9 (12) into the
vertical gap. Make sure the strip sits on top of the joining
plate Fig. 9 (5).
uPeel the protective film off the cover strip.*
Fig. 10
uOn the top of the appliances, press the short strip
Fig. 10 (13) into the gap. Make sure the front edge of the
strip is flush with the joining plate Fig. 10 (3).
uClip the cover Fig. 10 (14) over the gap between the two
control panel covers. Make sure the side edges of the
cover are flush with the control panel covers. To enable
this, the cover is expandable.
Fig. 11
uFit the bottom cover Fig. 11 (15) from above onto the
joining plate Fig. 11 (5) and snap it in at the bottom.
uConnect the combination to the mains according to the
manual.
Appliances with IceMakers:
uConnect the appliance to the fixed water connection
according to the manual.
NOTICE
Risk of damage when moving the combined SBS appliance!
The combined SBS appliance is heavy once assembled. The
appliance may be dented by improper movement.
uObserve the information given on moving the appliance
(see above).
uCarefully slide the combination into the intended posi‐
tion.
uIf necessary, align the height with the height-adjustable
feet.
uLower the centre height-adjustable feet Fig. 4 (C) until
they touch the floor.
uThen support the door: Extend the height-adjustable feet
Fig. 4 (A) at the turn hinge until they are resting on the
floor, then turn them further by 90°.
6 Disposing of packaging
WARNING
Danger of suffocation due to packing material and plastic
film!
uDo not allow children to play with packing material.
The packaging is made of recyclable materials:
-corrugated board/cardboard
-expanded polystyrene parts
-polythene bags and sheets
-polypropylene straps
-nailed wooden frame with polyethylene panel*
uTake the packaging material to an official collecting
point.
Disposing of packaging
6 * Depending on model and options
Disposing of packaging
* Depending on model and options 7
Liebherr-Hausgeräte Marica EOOD
4202 Radinovo
Bezirk Plovdiv
Bulgarien
home.liebherr.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Liebherr SGNes 3010 Premium Assembly And Installation Instructions
- Type
- Assembly And Installation Instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI