Horizon Fitness PARAGON 5 Owner's manual

TREADMILL OWNER’S MANUAL

Read the TREADMILL GUIDE before using this OWNER’S MANUAL.

PARAGON 4

PARAGON 5

PARAGON 6

2

3

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly

instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the

treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage

to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your treadmill’s serial number located on the front stabilizer tube and enter it in the space provided

below. Also locate the model name which is next to the serial number.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:

WARNING

SERIAL NUMBER:

MODEL NAME: HORIZON TREADMILL

4

Paragon 6

shown

KONSOLE

LÜFTER

AN/AUS SCHALTER

HAUPTSICHERUNG

STROMKABEL

KONSOLENKONTROLLE UND DISPLAYFENSTER

SICHERHEITSSCHLÜSSEL HALTERUNG

ENDKAPPE

HINTERE JUSTIERFÜßE

REICHWEITEKONTROLLE

FLASCHENHALTER

ARMSTANGEN MIT PULSFÜHLERN

TRANSPORTROLLEN

LESEGESTELL

ARMSTANGE

KONSOLENMASTABDECKUNG

MOTORABDECKUNG

SEITLICHE TRITTFLÄCHE

KONSOLENMAST

LAUFMAT TE

5

TOOLS INCLUDED:

F5 mm L-Wrench/Screwdriver

F6 mm T-Wrench

FScrewdriver (not included)

PARTS INCLUDED:

F1 Console Assembly

F2 Console Masts

F1 Hardware Kit

F1 Safety Key

F1 Power Cord

F2 Handlebar Cover Set

F2 Water Bottle Holder

If you have questions or if

there are any missing parts,

contact your local dealer.

NEED HELP?

DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill

from packaging until specified to do so in the assembly instructions. You may

remove the plastic wrap from console masts.

WARNING

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a

protective covering on your floor. Take CAUTION when handling and transporting this

unit. Never open box when it is on its side. Once the banding straps have been removed,

do not lift or transport this unit unless it is fully assembled. Unpack and assemble the unit

where it will be used. Never grab hold of any portion of the incline frame and attempt to

lift or move the treadmill.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

WARNING

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and

partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any grease,

such as lithium bike grease is recommended.

PRE ASSEMBLY

ALL

MODELS

6

HARDWARE FOR STEP 1 :

ASSEMBLY STEP 1

A Cut the yellow banding straps and lift the running

deck upward to remove all contents from underneath

the running deck.

B Open HARDWARE BAG 1

C Screw in the 2 BOLTA to the MAIN FRAME

BRACKET.

D Connect the CONSOLE CABLES at RIGHT

CONSOLE MAST an carefully tuck wires to

CONSOLE MAST to avoid damage.

E Align and attach right CONSOLE MAST with MAIN

FRAME BRACKET using BOLTA and repeat on the

other side.

B O LT (A)

M8 x 10

Qty: 2

NOTE: Do not pinch console cable when placing

the mast onto the main frame bracket. You may

need extra help assembling step 1 o 2

Paragon 6

Shown

BOLT(A)

MAIN FRAME BRACKET

RIGHT CONSOLE MAST

LEFT CONSOLE MAST

7

ASSEMBLY STEP 2

BOLT (B)

M8 x 70 mm

Qty: 8

SPRING WASHER (C)

Φ 8.2 mm

Qty: 8

FLAT WASHER (D)

Φ 8.2 mm

Qty: 8

HARDWARE FOR STEP 2 : A Open HARDWARE BAG 2

B Attach CONSOLE MAST to MAIN FRAME

BRACKET using 4 BOLTS B, 4 SPRING

WASHERS C and 4 FLAT WASHERS D.

C Repeat step B on other side.

NOTE: Do not tighten bolts until step 4 is complete.

Paragon 6

Shown

LEFT CONSOLE MAST

RIGHT CONSOLE MAST

FLAT WASHERS (D)

SPRING WASHERS (C)

BOLTS (B)

8

A Open HARDWARE BAG 3.

B Slide HANDLEBAR onto CONSOLE MAST

BRACKET and attach using 3 BOLTS E, 3

SPRING WASHERSSF, 2 FLAT WASHERSG &

1 ARC WASHER H.

(Refer to graphic at left for more details)

C Repeat on other side.

NOTE: Be careful not to pinch any wires.

BOLT (E)

M8 x 20 mm

Qty: 6

FLAT WASHER (G)

Φ 8.2 mm

Qty: 4

ARC WASHER (H)

Φ 8.2 mm

Qty: 2

SPRING WASHER (F)

Φ 8.2 x Φ14

Qty: 6

ASSEMBLY STEP 3

HARDWARE FOR STEP 3 :

SPRING WASHER (F)

FLAT WASHER (G)

ARC WASHER (H)

HANDLEBAR

CONSOLE MAST BRACKET

BOLT (E)

Paragon 6

Shown

9

ASSEMBLY STEP 4

A Open HARDWARE BAG 4.

B Gently hold the CONSOLE above the

CONSOLE MAST.

C Connect the CONSOLE CABLES, carefully

tucking wires in masts to avoid damage.

D Attach the CONSOLE to the CONSOLE

MAST using 4 BOLTS I, 4 SPRING

WASHERS C and 4 FLAT WASHERS D.

E Fold the DECK into the upright position until

the foot latch engages. Make sure the spacing

between the HANDLEBARS and the DECK

are the same then tighten BOLTS from step 2

to step 4.

BOLT (I)

M8 x 15 mm

Qty: 4

FLAT WASHER (D)

Φ 8.2 mm

Qty: 4

SPRING WASHER (C)

Φ 8.2 mm

Qty: 4

HARDWARE FOR STEP 4 :

BOLT (I)

SPRING WASHER (C)

FLAT WASHER (D)

BOLT (I)

SPRING WASHER (C)

FLAT WASHER (D)

(PARAGON 6)

Paragon 6

Shown

10 (PARAGON 6)

ASSEMBLY STEP 5

HARDWARE BAG 5:A Open HARDWARE BAG 5.

B Carefully attach RIGHT CONSOLE MAST OUTER

& INNER COVER together using 4 SCREWS J

and adjust the gaps between console shell and

CONSOLE MAST OUTER COVERS. Then tighten 4

BOLTS (I) from step 4

C Attach the left and right INNER COVERS using 4

SCREWS (J).

RIGHT HANDLEBAR

RIGHT COVER

LEFT COVER

SCREW (J)

Φ 4 x 12

Qty: 8

NOTE: Connect and screw in the outer cover

before fixing the inner cover. Be careful not to

scratch or brake the plastic while assembling.

Make sure the cover set is centered and well

assembled before tighten the screws.

Paragon 6

Shown

11

ASSEMBLY STEP 5

A Gently attach the LEFT WATER BOTTLE HOLDER

to the CONSOLE with front edge facing down.

B Once the LEFT WATER BOTTLE HOLDER is in

place carefully push through the WATTER BOTTLE

HOLDER to its position until you hear a“click”at rear

edge.

C Make sure the LEFT WATER BOTTLE HOLDER is

well assembled then fix it with 1 SCREW K from

the back.

D Repeat the previous step on the opposite side.

HARDWARE FOR STEP 5 :

LEFT WATER

BOTTLE HOLDER

SCREW (K)

RIGHT WATER

BOTTLE HOLDER

SCREW (K)

Φ 4 x 10

Qty: 2

(PARAGON 6)

Paragon 6

Shown

12

ASSEMBLY STEP 7

YOU ARE FINISHED!

Paragon 4

Max. User Weight: 136 kg / 300 lbs.

Product Weight: 100 kg / 220 lbs.

Overall Dimension: 182 x 91 x 149 cm / 72” x 36” x 59”

Folding Dimension: 99 x 91 x 168 cm / 39” x 36” x 66”

Complies with EN957-1, EN957-6, HB

Paragon 5

Max. User Weight: 159 kg / 350 lbs.

Product Weight: 103 kg / 227 lbs.

Overall Dimension: 182 x 91 x 149 cm / 72” x 36” x 59”

Folding Dimension: 99 x 91 x 168 cm / 39” x 36” x 66”

Complies with EN957-1, EN957-6, HB

Paragon 6

Max. User Weight: 159 kg / 350 lbs.

Product Weight: 110 kg / 243 lbs.-127 kg / 280 lbs.

Overall Dimension: 194 x 91 x 149 cm / 76” x 36” x 59”

Folding Dimension: 105 x 91 x 178 cm / 41” x 36” x 70”

Complies with EN957-1, EN957-6, HB

(PARAGON 6)

Paragon 6

Shown

13

15

TREADMILL OPERATION

This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the

TREADMILL GUIDE has instructions for the following:

• LOCATION OF THE TREADMILL

• USING THE SAFETY KEY

• FOLDING THE TREADMILL

• MOVING THE TREADMILL

• LEVELING THE TREADMILL

• TENSIONING THE RUNNING BELT

• CENTERING THE RUNNING BELT

• USING THE HEART RATE FUNCTION

16

EnergySaver

ENERGIESPARMODUS

Attach saf ety key clip to clot hing before sta rting and remove s afety key when not i n use. Heart rate m onitoring sys tems

may be inaccur ate. Over exercis e may result in seri ous injury or dea th. To avoid injury, stan d on the side rails be fore

startin g treadmill. Read an d follow all instr uctions befo re operating. Ke ep children away fr om this equipmen t.

WARNING! Model is only for h omeuse.

Befestigen Sie den Sicherheitsclip an Ihrer Kleidung, bevor Sie das Gerät starten. Herzfrequenzüberwachungssysteme

können ungen au sein. Übermäß iges Training kann zu e rnsthaften Ve rletzungen od er zum Tod führen. Um das Ri siko

von Verletzungen einzudämmen, stellen Sie sich auf die seitlichen Trittflächen, bevor Sie das Gerät starten.

Lesen und befolgen Sie die Bedienungsanleitung vor der Erstbenutzung. Halten Sie Kinder von dem Gerät fern.

WARNUNG! Nur für den Heim gebrauch.

INCLINE

STEIGUNG

TIME

ZEIT DISTANCE

ENTFERNUNG

SPEED

GESCHWINDIGKEIT

A B C

F G H H LKD E M O PN

AGE

ALTER

HR (Beats Per Minute)

HR (Pulsschlag pro Minute)

220 - AGE = MHR

(220 - ALTER = MHR)

(MAXIMUM HEART RATE)

(MAXIMALE HERZFREQUENZ)

HIGH

MAXIUMUM

(80%-100%)

MODERATE

DURCHSCHNITT

(65%-85%)

LOW

MINIMUM

(55%-65%)

220

200

180

160

140

120

100

80

20 25 30 35 40 45 50 55 60 65 70

km/h

mph

8

5

km/h

mph

18

11

2

%

4

%

6

%

8

%

10

%

12

%

SET SPEED

GESCHWINDIGKEIT BESTÄTIGEN

SET INCLINE

STEIGUNG BESTÄTIGEN

km/h

2

mph

km/h

mph

4

3

2

km/h

mph

16

10

km/h

mph

12

8

STOP

HOLD TO RESET

FÜR NULLSTELLUNG GEDRÜCKT HALTEN

ENTER

EINGABE

START

QUICK START

SCHNELLSTART

CHANGE

DISPLAY

ANZEIGENWECHSEL

TARGET HEART RATE ZONE

ZIELHERZFREQUENZZONEN

PARAGON 4

JI

CALORIES KALORIEN

HEART RATE

HERZFREQUENZ

Paragon 4

Shown

17

PARAGON 4 CONSOLE OPERATION

Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

A LED DISPLAY WINDOWS: Time, Distance, Speed, Incline, Calories, Heart Rate.

B DOTMATRIX DISPLAY WINDOW: displays workout level, progress and workout profiles.

C ENERGY SAVER : To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by mode

for 15 mins) and could be quickly waken up with a touch of a button.

D INCLINE KEYS : used to adjust incline in small increments (0.5% Increments).

E CHANGE DISPLAY BUTTON: used to scroll through display modes. Press to change display feedback during workout.

F START: press to begin exercising, start your workout, or resume exercising after pause.

G SET INCLINE BUTTON : used to confirm quick adjustment of incline.

H QUICK ADJUST KEYPAD : used to reach desired speed or incline more quickly.

I MULTIPLE STORAGE AREA : used to keep your cellphone, keys or remote controller.

J SAFETY KEY POSITION: enables treadmill when safety key is inserted.

K READING RACK : holds reading materials.

L SET SPEED BUTTON: used to confirm quick adjustment of speed.

M STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.

N ENTER BUTTON: used to confirm setting of workout program or user profile.

O SPEED KEYS : used to adjust speed in small increments (0.1 KMH increments).

P WATER BOTTLE POCKETS : holds personal workout equipment.

Paragon 4

Shown

18

FAN

VENTILATOR

2

%

4

%

6

%

8

%

10

%

12

%

SET SPEED

GESCHWINDIGKEIT BESTÄTIGEN

SET INCLINE

STEIGUNG BESTÄTIGEN

km/h

mph

km/h

mph

km/h

mph

4

3

8

5

km/h

mph

km/h

mph

16

10

18

12

km/h

mph

12

8

2

PRESS TO SWITCH

PERFORMANCE FILING SYSTEM

FÜR ANZEIGENWECHSEL DRÜCKEN

PARAGON 5

EnergySaver

ENERGIESPARMODUS

Attach saf ety key clip to clot hing before sta rting and remove s afety key when not i n use. Heart rate m onitoring sys tems

may be inaccur ate. Over exercis e may result in seri ous injury or dea th. To avoid injury, stan d on the side rails be fore

startin g treadmill. Read an d follow all instr uctions befo re operating. Ke ep children away fr om this equipmen t.

WARNING! Model is only for h omeuse.

Befestigen Sie den Sicherheitsclip an Ihrer Kleidung, bevor Sie das Gerät starten. Herzfrequenzüberwachungssysteme

können ungen au sein. Übermäß iges Training kann zu e rnsthaften Ve rletzungen od er zum Tod führen. Um das Ri siko

von Verletzungen einzudämmen, stellen Sie sich auf die seitlichen Trittflächen, bevor Sie das Gerät starten.

Lesen und befolgen Sie die Bedienungsanleitung vor der Erstbenutzung. Halten Sie Kinder von dem Gerät fern.

WARNUNG! Nur für den Heim gebrauch.

A B

G H I I PML OE F Q S TR

STOP

HOLD TO RESET

FÜR NULLSTELLUNG GEDRÜCKT HALTEN

ENTER

EINGABE

START

QUICK START

SCHNELLSTART

CHANGE

DISPLAY

ANZEIGENWECHSEL

K

DC

J N

Paragon 5

Shown

19

PARAGON 5 CONSOLE OPERATION

Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

A LCD DISPLAY WINDOWS: Time, Distance,Speed, Incline, Calories, Heart Rate.

B DOTMATRIX DISPLAY WINDOW: displays workout level, progress and workout profiles.

C COMMUNICATION WINDOW: Passport synchronisation, proFILE display information and other communication texts.

D ENERGY SAVER : To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by mode

for 15 mins) and could be quickly waken up with a touch of a button.

E INCLINE KEYS : used to adjust incline in small increments (0.5% Increments).

F CHANGE DISPLAY BUTTON: used to scroll through display modes. Press to change display feedback during workout.

G START: press to begin exercising, start your workout, or resume exercising after pause.

H SET INCLINE BUTTON : used to confirm quick adjustment of incline.

I QUICK ADJUST KEYPAD : used to reach desired speed or incline more quickly.

J MULTIPLE STORAGE AREA : used to keep your cellphone, keys or remote controller.

K FAN BUTTON: Allows user to select among 3 different fan speed.

L FAN: High quality personal blower fan provides 3 stages adjustment.

M SAFETY KEY POSITION: enables treadmill when safety key is inserted.

N READING RACK : holds reading materials.

O PROFILE BUTT ON: used to scroll through proFILE display modes. Must be pressed after selecting user.

P SET SPEED BUTTON: used to confirm quick adjustment of speed.

Q STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.

R ENTER BUTTON: used to confirm setting of workout program or user profile.

S SPEED KEYS : used to adjust speed in small increments (0.1 KMH increments).

T WATER BOTTLE POCKETS : holds personal workout equipment.

Paragon 5

Shown

20

FAN

VENTILATOR

SET SPEED

GESCHWINDIGKEIT BESTÄTIGEN

SET INCLINE

STEIGUNG BESTÄTIGEN

PRESS TO SWITCH

PERFORMANCE FILING SYSTEM

FÜR ANZEIGENWECHSEL DRÜCKEN

PARAGON 6

EnergySaver

ENERGIESPARMODUS

Befestigen Sie den Sicherheitsclip an Ihrer Kleidung, bevor Sie das Gerät starten. Herzfrequenzüberwachungssysteme

können ungen au sein. Übermäß iges Training kann zu e rnsthaften Ve rletzungen od er zum Tod führen. Um das Ri siko

von Verletzungen einzudämmen, stellen Sie sich auf die seitlichen Trittflächen, bevor Sie das Gerät starten.

Lesen und befolgen Sie die Bedienungsanleitung vor der Erstbenutzung. Halten Sie Kinder von dem Gerät fern.

WARNUNG! Nur für den Heim gebrauch.

A B

G H I I PML OE F Q S TR

STOP

HOLD TO RESET

FÜR NULLSTELLUNG GEDRÜCKT HALTEN

ENTER

EINGABE

START

QUICK START

SCHNELLSTART

CHANGE

DISPLAY

ANZEIGENWECHSEL

K

D

J N

2

%

4

%

6

%

8

%

10

%

15

%

km/h

mph

km/h

mph

km/h

mph

4

3

8

5

km/h

mph

km/h

mph

16

10

20

12

km/h

mph

12

8

2

C

Attach saf ety key clip to clot hing before sta rting and remove s afety key when not i n use. Heart rate m onitoring sys tems

may be inaccur ate. Over exercis e may result in seri ous injury or dea th. To avoid injury, stan d on the side rails be fore

startin g treadmill. Read an d follow all instr uctions befo re operating. Ke ep children away fr om this equipmen t.

WARNING! Model is only for h omeuse.

Paragon 6

Shown

Page is loading ...

Horizon Fitness PARAGON 5 Owner's manual

This manual is also suitable for

Horizon Fitness PARAGON 5 Owner's manual

Related papers

Other documents