Fabtech Motorsports | 4331 Eucalyptus Ave. Chino, CA 91710
Tech Line: 909-597-7800 | Fax: 909-597-7185 | Web: www.fabtechmotorsports.com
INSTALLATION INSTRUCTIONS
2020 JEEP GLADIATOR 4WD
REAR LONG ARM KIT
FTS24252
NOTE: TO ORDER WEARABLE REPLACEMENT COMPONENTS DO NOT USE PART NUMBERS SHOWN ON THIS
INSTRUCTION SHEET. GO TO FABTECH WEBSITE AND LOOK UP WEARABLE REPLACEMENT PARTS TO FIND THE PROPER
PART NUMBER TO ORDER.
FTS24252 REAR LONG ARM LINK KIT
2 FT50771 REAR LINK (LOWER)
2 FT50772 REAR LINK (UPPER)
1 FT50800 HARDWARE SUBASSEMBLY
FT50800 HARDWARE SUBASSEMBLY
8 FT1007 HALF BUSHING
1 FT24252i INSTRUCTIONS
8 FT50594 MISALIGNMENT 1” BEARING
4 FT615 SLEEVE 1.000 X .630 X .2.645
4 FT84 GREASE FITTING 1/4-28
1 FTAS12 STICKER FT BLUE 10X4 DIE CUT
1 FTAS16 DRIVER WARNING DECAL
1 FTLUBE URETHANE LUBE
1 FTREGCARD REGISTRATION CARD
2 of 4
For technical assistance call: 909-597-7800 or e-mail: [email protected]
READ THIS BEFORE YOU BEGIN INSTALLATION -
Check all parts to the parts list above before beginning installation. If any parts are missing contact Fabtech at 909-597-7800
and a replacement part will be sent to you immediately.
Read all instructions thoroughly from start to finish before beginning the installation. If these instructions are not properly
followed severe frame, driveline and / or suspension damage may occur.
Check your local city and state laws prior to the installation of this system for legality. Do not install if not legal in your area.
Prior to the installation of this suspension system perform a front end alignment and record. Do not install this system if the
vehicle alignment is not within factory specifications. Check for frame and suspension damage prior to installation.
The installation of this suspension system should be performed by two professional mechanics.
This suspension must be installed with Fabtech shock absorbers.
Installation of all fasteners requires the use of provided thread locking compound with proper torque values as indicated
throughout the installation. Apply thread locking compound upon the final torque of the fastener.
WARNING- Installation of this system will alter the center of gravity of the vehicle and may increase roll over as compared
to stock.
Vehicles that receive oversized tires should check ball joints, uniballs, tie rods ends, pitman arm and idler arm every 2500-
5000 miles for wear and replace as needed.
Verify differential fluid is at manufactures recommended level prior to kit installation. Installation of the kit will reposition the
differential and the fill plug hole may be in a different position. (For example, if the manufacture recommends 3 quarts of fluid,
make sure the diff has 3 quarts of fluid). Check your specific manual for correct amount of fluid.
Periodically grease the bushings using a urethane compatible grease.
FOOTNOTES -
-
- PRE-INSTALLATION NOTES -
Required Tools (Not Included)
Basic Hand Tools
Floor Jack
Jack Stands
Assorted Metric and S.A.E sockets, and Allen wrenches
Torque Wrench
- TOOL LIST -
NOTE: REFER TO OPTIONAL KIT BOX INSTRUCTIONS PRIOR TO
INSTALLATION.
3 of 4
- INSTRUCTIONS -
REAR SUSPENSION-
1. Jack up the rear end of the vehicle and support the
frame rails with jack stands. NEVER WORK UNDER AN
UNSUPPORTED VEHICLE! Remove the rear tires.
2. Using the supplied grease, grease and install two FT1007
(Bushings), a FT615 (Sleeve) and a zerk tting into the end
of each link arm.
3. With the axle supported, remove the driver side lower link
and save hardware.
4. Install FT50771 (Lower Link) into the factory mounts using
two FT50594 (Misalignments) and the factory hardware.
Torque to 160 ft-lbs. NOTE: The rod end will be installed
at the axle side and the grease fitting should be facing
upwards on the frame side.
5. Remove the driver side upper link and save hardware.
6. Install FT50772 (Upper Link) into the factory mounts using
two FT50594 (Misalignments) and the factory hardware.
Torque to 160 ft-lbs. NOTE: The rod end will be installed
at the axle side and the grease fitting should be facing
upwards on the frame side. SEE FIGURE 1
7. Repeat steps on the passenger side.
FIGURE 1 - STEP 6
8. Install tires and wheels and torque lug nuts to wheel
manufacturer’s specications.
9. Recheck all bolts for proper torque.
10. Install Driver Warning Decal. Complete product
registration card and mail to Fabtech in order to receive
future safety and technical bulletins on this suspension.
Vehicles that will receive oversized tires should check ball
joints, uniballs and all steering components every
2500-5000 miles for wear and replace as required.
RETORQUE ALL NUTS, BOLTS AND LUGS
AFTER 50 MILES AND PERIODICALLY
THEREAFTER.
For technical assistance call: 909-597-7800
4 of 4
- Product Warranty and Warnings -
Fabtech provides a Limited Lifetime Warranty to the original retail purchaser who owns the vehicle, on which the product was
originally installed, for defects in workmanship and materials.
The Limited Lifetime Warranty excludes the following Fabtech items; bushings, bump stops, ball joints, tie rod ends, limiting
straps, cross shafts, heim joints and driveshafts. These parts are subject to wear and are not considered defective when worn.
They are warranted for 60 days from the date of purchase for defects in workmanship.
Dirt Logic and Performance Coilover take apart shocks are considered a serviceable shock with a one year warranty on leakage
only. Service seal kits are available separately for future maintenance. All other shocks are covered under our Limited Lifetime
Warranty.
Fabtech does not warrant any product for finish, alterations, modifications and/or installation contrary to Fabtech’s instructions.
Alterations to the finish of the parts including but not limited to painting, powder coating, plating and/or welding will void all
warranties. Some finish damage may occur to parts during shipping, which is considered normal and is not covered under
warranty.
Fabtech products are not designed nor intended to be installed on vehicles used in race applications or for racing purposes or
for similar activities. (A “RACE” is defined as any contest between two or more vehicles, or any contest of one or more vehicle
against the clock, whether or not such contest is for a prize). This warranty does not include coverage for police or taxi vehicles,
race vehicles, or vehicles used for government or commercial purposes. Also excluded from this warranty are sales outside of
the United States of America.
Installation of most suspension products will raise the center of gravity of the vehicle and will cause the vehicle to handle
differently than stock. It may increase the vehicle’s susceptibility to a rollover, on road and off road, at all speeds. Extreme care
should be taken to operate the vehicle safely at all times to prevent rollover or loss of control resulting in serious injury or death.
Fabtech front end Desert Guards may impair the deployment or operation of vehicles equipped with supplemental restraining
systems/air bag systems and should not be installed if the vehicle is equipped as so.
Fabtech makes every effort to ensure suspension product compatibility with all vehicles listed on the website, but due
to unknown auto manufacturer’s production changes and/or inconstancies by the auto manufacturer, Fabtech cannot be
responsible for 100% compatibility, including the fitment of tire and wheel sizes listed. The Tire and Wheel sizes listed in
Fabtech’s website are only a guideline for street driving with noted fender trimming. Fabtech is not responsible for damages
to the vehicle’s body or tires. Fabtech is not responsible for premature wear of factory components due to the installation of
oversized tires and wheels.
Fabtech’s obligation under this warranty is limited to the repair or replacement, at Fabtech option, of the defective product only.
All costs of removal, installation or re-installation, freight charges, incidental or consequential damages are expressly excluded
from this warranty. Fabtech is not responsible for damages and/or warranty of other vehicle parts related or non related to the
installed Fabtech product. This warranty is expressly in lieu of all other warranties expressed or implied. This warranty shall not
apply to any product that has been subject to accident, negligence, alteration, abuse or misuse as determined by Fabtech.
Fabtech suspension components must be installed as a complete system including shocks as shown on our website. All
warranties will become void if Fabtech parts are combined and/or substituted with other aftermarket suspension products.
Combination and/or substitution of other aftermarket suspension parts may cause premature wear and/or product failure
resulting in an accident causing injury or death. Fabtech does not warrant products not manufactured by Fabtech.
Depending on the condition of the factory suspension components retained after the installation of a Fabtech suspension not
all vehicles may have the same ride stance front to rear as described in the website. The blue color of suspension components
shown in all Fabtech photographs are for display purposes only. Majority of all Fabtech components will be black specifically
where noted with part numbers ending in BK.
Installation of Fabtech product may void the vehicles factory warranty; it is the consumer’s responsibility to check with their
local vehicle’s dealer for warranty disposition before the installation of the product. Some state laws may prohibit modification of
suspension to a vehicle in whole or in part. It is the responsibility of the installer and consumer to consult local laws prior to the
installation of any Fabtech suspension product to comply with such written laws.
It is the responsibility of the distributor and/or the retailer to review all warranties and warnings of Fabtech products with the
consumer prior to purchase.
Fabtech reserves the right to super cede, discontinue, change the design, finish, part number and/or application of parts when
deemed necessary without written notice. Fabtech is not responsible for misprints or typographical errors within the website or
price sheet. For the most recent Product Warranty and Warnings visit our website www.fabtechmotorsports.com
Instruction Sheet Part# - FT24252i 10/30/19
-
1
-
2
-
3
-
4
Fabtech K4177M Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Fabtech K4229DL Installation guide
-
-
-
-
-
-
-
Fabtech FTS22293 User manual
-
Fabtech FTS24132 User manual
-