2. ekwb
  3. EK-Quantum Vector Trio RTX 2080 D-RGB Upgrade Kit

ekwb EK-Quantum Vector Trio RTX 2080 D-RGB Upgrade Kit Installation guide

  • Hello, I am a chat assistant that has reviewed the EKWB Vector D-RGB Upgrade Kit installation manual. The document explains how to upgrade your water block with D-RGB LEDs, covering steps like disconnecting old LEDs, installing new components, and connecting the D-RGB strip to your motherboard. I'm ready to answer your questions about this upgrade process.
  • What should I do before starting the installation?
    What should I do after attaching the new stickout and D-RGB LED?
    What is the correct way to power the D-RGB LED strip?
INSTALLATION MANUAL
EKQuantum
Vector D-RGB Upgrade Kit
- 2 -
This product is intended for installation by expert users only. Please
consult with a qualified technician. Improper installation may result
in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products or their
installation. The following instructions are subject to change without
notice. Please, read the manual carefully before beginning with the
installation process.
- 3 -
TABLE OF CONTENT
DISCONNECT THE LEDs 4
REPLACE THE STICKOUT 4
ATTACHING THE NEW STICKOUT AND D-RGB LED 5
PLEXI VERSION 5
ACETAL VERSION 5
ATTACHING THE D-RGB TERMINAL COVER 6
IMPORTANT INFORMATION 6
CONNECTING THE D-RGB LED STRIP 7
SUPPORT AND SERVICE 8
SOCIAL MEDIA 8
- 4 -
DISCONNECT THE LEDs
First, disconnect the cable between the Terminal Cover and Stickout.
After that, remove the Terminal Cover from the FC Terminal.
Remove the Stickout from the water block and store the screws for
later use.
If you have the Acetal version of the water block, do not
forget to remove the RGB LED from the Acetal part.
REPLACE THE STICKOUT
Stickout
Stickout Screws
- 5 -
ATTACHING THE NEW STICKOUT AND D-RGB LED
Stickout
PLEXI VERSION
Take the Stickout and D-RGB LED from the box.
Remove the protective foil from D-RGB LED and attach the LED to the
Stickout.
After this, use the stored screws to secure the Stickout to the Plexi part.
D-RGB LED
Stickout
ACETAL VERSION
Take the Stickout and D-RGB LED from the box.
Remove the protective foil from D-RGB LED and attach the LED to the
Acetal. D-RGB is oriented towards the Stickout.
After this, use the stored screws to secure the Stickout to the Acetal part.
D-RGB LED
- 6 -
IMPORTANT INFORMATION
Do not forget to connect the D-RGB LED cable of the Stickout
to the cable of the Terminal Cover.
In case you have 2 (two) Stickouts:
First, connect the Stickout cables and then you can connect
them to the Terminal Cover cable!
Take the pre-assembled D-RGB Terminal Cover from the box and
attach it to the FC Terminal.
ATTACHING THE D-RGB TERMINAL COVER
- 7 -
CONNECTING THE D-RGB LED STRIP
Plug the 3-pin connector from the water block’s D-RGB LED light in
the D-RGB HEADER on the motherboard. The LED will work if the pin
layout on the header is as follows: +5V, Digital.
Please ensure that the arrow indicated on the connector is
plugged into the +5V line as indicated on your motherboard.
If you connect the LE Diode to the 12V RGB HEADER you
can damage the LEDs.
D-RGB Header
RGB Header
For assistance please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA
/