Premier Mounts PCM-100 Operating instructions

PCM-100

Installation Instructions

Step 1

Invert the display and place it on a soft and flat surface. Locate the mounting points on the back of the plasma display.

Identify the correct plasma bracket mounting hardware for your plasma display from the chart shown on the back of the

assembly manual and secure the (L) Left and (R) Right hand side mounting brackets to the plasma using the

corresponding hardware (supplied). Note: Make sure the upper “clevis” hook mounting screw, nut and reference arrow

are facing to the left and right outside edges of the display.

Step 2

Determine the desired height for the bottom edge of the display on the wall.

Temporarily slide the round steel rod portion of one of the universal (WP) wall plates fully into the bottom receiving slots

of the installed plasma mounting brackets. Measure the distance between the bottom outside edge of the plasma

display and the bottom outside edge of the lower wall mounting plate. Add the desired bottom edge height of the

display to the distance between the bottom edge of the wall plate and the bottom edge of the display to determine the

correct mounting height of the lower wall plate. Example: Overall desired height for the bottom outside of the display is

60". Difference between the bottom edge of the display and the bottom edge of the lower wall plate fully installed in the

lower receiving slots of the brackets is 4" means the lower wall plate bottom outside edge should be placed at 64" from

the floor (60" + 4" = 64"). Determine the desired wall location and its ability to properly support the weight of the display.

Locate and mark the dual 16" or 24" wood stud centers closest to the desired plasma placement area. Measure up

from the floor the proper distance to the bottom edge of the lower wall plate and mark a level reference line on the wall.

Place the lower wall plate bottom edge on the reference line and mark the best four (4) each wall plate lag bolt

mounting points through the wall plate slots on the wall. Install on a level the bottom wall plate with the wall plate

reference arrow pointing up to the wall using the (4) four 5/16" Lag bolts and flat washers (supplied).

Note: The wall plate provides you with three (3) 16" stud center patterns and one (1) 24" stud center pattern to assist

you in your installation.

Step 3

With the lower wall plate securely installed and level with the floor place the “supplied” upper wall plate cardboard

placement template over the top and outside edges of the lower wall plate. Place bottom and outside edges of the

upper wall plate into the top portion of the template and mark the duplicate set of mounting points for the upper wall

plate to the wall. Secure the upper wall plate to the wall in the same manner as the lower plate using the four (4) 5/16"

lag bolts and flat washers. With the two wall plates properly secured to the wall the separation template should be used

to recheck the proper separation between the upper and lower plates.

Step 4

With the upper “clevis” tilt hooks on the plasma brackets in the flat on wall position raise the plasma display with

brackets attached (2 people minimum recommended) and place the plasma display flat against wall with the upper and

lower plasma bracket attaching slots slightly higher than the steel receiving rods of the upper and lower wall plates.

With the plasma reasonably level lower the display until the display brackets receiving slots are fully installed into the

upper and lower wall plate steel rods. Gently pull the left and right upper edges of the display to extend the mount to its

maximum 10° tilt and install finger tight the two upper “clevis” arm 6 (mm) safety knobs one on each mounting bracket.

Step 5

Once the display on wall installation is complete you still can move the display from left to right or right to left to optimize

the final position of the display on the wall by gently sliding the unit on the steel rods of the wall plate. This adjustment

distance will vary depending on the display model being installed.

NOTE: Do not over tighten the bracket mounting screws as damage to the display internal mounting threads

could occur.

Note: To remove the display from the wall simply extend the display to its maximum tilt range, remove the two

6 (mm) safety knobs push the display back to its flat wall position and lift the unit up and out from the wall.

OTE: Some of the hardware may be left out if all the assign mounting points on the bracket are used.

Note: The 8 (mm) nuts for your coarse tension adjustment and the 5 (mm) screws for your fine tension

adjustment.

www.touchboards.com 205 Westwood Ave.Long Branch, NJ 07740 1-866-942-6273 [email protected]

A PCM Mount Brackets L/R

B Hardware See Chart

C Nylon Spacers (SP) See Chart

D Wall Brackets 2

E Template 1

F 5/16" Lag Bolts 8

G 5/16" Flat Washers 8

H 6 mm x 12 mm Securing Knobs 2

PCM-100

Note: When the display brackets receiving slots are fully installed into the upper and lower wall plate steel rods

and the plasma is on its flat position, there is a 7/8" gap from the top of the rod to the end of the hook. This

feature is to com

ensate for tiltin

Note: Arrows on the wall brackets must

be facing up prior to installation. Secure

the lag bolts into the center of the wood

stud.

BRAND MODEL # MP HARDW ARE PACK

Dwin HD50 3,9 (4) 8 (m m ) x 30 (m m ) (SP) PK 2

Fujitsu 4211, 4212, 4221, 4222, 4208, 4209, 4213, 4214,

4229, 4241, 4242 2,6 (4) 5 (m m ) x 16 (m m ) PK 1

Fujitsu P42HH A10 3,9 (6) 8 (m m ) x 20 (m m ) PK 4

Fujitsu P50X H A10 3.A,11.1 (6) 8 (m m ) x 30 (m m ) PK 7

Fujitsu 5001, 5002 3,9 (4 ) 8 (m m ) x 3 0 (m m ) (S P ) P K 2

Fujitsu PD S6101 4.1,12 (4 ) 8 (m m ) x 3 0 (m m ) (S P ) P K 2

Hitachi C M P500W X U 3,5,8 (6) 8 (m m ) x 20 (m m) PK 4

JVC G D V 500PZ U 3,9 (4 ) 8 (m m ) x 3 0 (m m ) (S P ) P K 2

LG M U40PA10 4,7,10 (6) 5 (m m ) x 20 (m m) (SP) PK 3

LG M U50P241 4,6.2,10 (6) 5 (m m ) x 16 (m m ) PK 1

LG M N42PZ10, M N 42PZ11, M U42PZ10 3.1,6.1,7.1 (6 ) 5 (m m ) X 1 6 (m m ) (S P ) N o te :

Use spacers from pack 3 PK 1

LG M U60P Z10 1,5,11 (6 ) 8 (m m ) x 2 0 (m m ) (S P ) P K 4

Panasonic

TH 37PW D4UZ,PT42P1, TC42P1F, 42PD2,

PT42PD3P, PT42PD1P, TH42PW D3U, PT37P1,

TC42P1, TH42PW D3, TH42PWD4UY,

TH42PW D4EX, TH50PHD3U, PT50PD3P,

TH50PHD3E

3,9 (4) 8 (m m ) x 30 (m m ) (SP) PK 2

Eizo P 5070, P5071 3,5,8 (6) 8 (m m ) x 30 (m m ) P K 7

Pioneer PDP4330HD,PDP501X, V502MX, V502X, V505,

PDP505HD,1000HD,PDP503CMX, PDP5030HD 3,5,8 (6) 8 (m m ) x 20 (m m ) PK 4

Runco PL42cx 3,9 (4 ) 8 (m m ) x 3 0 (m m ) (S P ) P K 2

Runco PL43HDX 3,5,8 (6) 8 (m m ) x 20 (m m) PK 4

Runco PL50c 3,5,8 (6 ) 8 (m m ) x 2 0 (m m ) P K 4

Sharp P Z43HV2U ,PD50,P Z50H V2U ,PZ43H V2U 3,5,8 (6 ) 8 (m m ) x 2 0 (m m ) P K 4

Toshiba PD42W , PD42W 1 3,9 (4 ) 8 (m m ) x 3 0 (m m ) (S P ) P K 2

Toshiba 50HP81 3,9 (4 ) 8 (m m ) x 3 0 (m m ) (S P ) P K 2

Viewsonic VPW 420 3,9 (4 ) 8 (m m ) x 3 0 (m m ) (S P ) P K 2

Viewsonic VPW 500 3,5,8 (6 ) 8 (m m ) x 2 0 (m m ) P K 4

Zenith DPDP40W ,P40V22,DPDP40V 4,7,10 (6) 5 (m m ) x 2 0 (m m ) (S P ) P K 3

Zenith P 50W 26 3.2,6.2,10 (6) 5 (m m ) x 16 (m m ) PK 1

Zenith P 42W 22 3.1,6.1,7.1 (6 ) 5 (m m ) X 1 6 (m m ) (S P ) N o te :

Use spacers from pack 3 PK 1

Zenith D PD P 60W , P60W 26 1,5,11 (6 ) 8 (m m ) x 2 0 (m m ) (S P ) P K 4

AKIRA SV-4201 1,9 (4) 8 (m m ) x 30 (m m ) (SP) PK 2

Yamaha PDM1 1,9 (4) 8 (m m ) x 30 (m m ) (SP) PK 2

#/LR DESCRIPTION QTY

R.08

LISTED

E176225

The wall should be capable of supporting a weight of 160 Lbs at least four (4) times the weight of the plasma display. More than 160 Lbs, the wall must be reinforced. Proper

installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury.

NOTE: During installation, the cardboard template (Item E) is required for proper separation of the wall plates. Do not discard cardboard template before using.