5KSM7580X, 5KSM7591X,
5KPM5, 5KSM6521X
W10648168A_ENv03.indd 1 12/11/13 11:48 AM
W10648168A_ENv03.indd 2 12/11/13 11:48 AM
English ................................................................................ 5
Deutsch ............................................................................ 00
Français ............................................................................00
Italiano .............................................................................. 00
Nederlands ...................................................................... 00
Español ............................................................................. 00
Português ......................................................................... 00
Ελληνικά ...........................................................................00
Svenska ............................................................................ 00
Norsk ................................................................................ 00
Suomi ................................................................................ 00
Dansk ................................................................................ 00
Íslenska ............................................................................. 00
Русский ............................................................................ 00
Polski ................................................................................. 00
Český ................................................................................ 00
............................................................................... 00
W10648168A_ENv03.indd 3 12/11/13 11:48 AM
W10648168A_ENv03.indd 4 12/11/13 11:48 AM
English
5
STAND MIXER INSTRUCTIONS
STAND MIXER SAFETY
Important safeguards .......................................................................................... 6
Electrical requirements ..................................................................................... 7
Electrical equipment waste disposal ................................................................... 7
PARTS AND FEATURES ........................................................................................ 8
ASSEMBLING THE STAND MIXER
Attaching the bowl and beaters .......................................................................... 9
Adjusting the beater to bowl clearance ............................................................ 10
OPERATING THE STAND MIXER
Speed control guide — 10 speed Stand Mixers ............................................... 11
Removing the bowl and beaters ....................................................................... 12
TIPS FOR GREAT RESULTS
Stand Mixer use ................................................................................................ 12
Mixing time ....................................................................................................... 13
Mixing tips ........................................................................................................ 13
ATTACHMENTS ................................................................................................... 13
CARE AND CLEANING ....................................................................................... 14
TROUBLESHOOTING ......................................................................................... 15
WARRANTY AND SERVICE
KitchenAid Stand Mixer warranty .................................................................... 16
Customer service ............................................................................................. 16
TABLE OF CONTENTS
W10648168A_ENv03.indd 5 12/11/13 11:48 AM
6
STAND MIXER SAFETY
STAND MIXER SAFETY
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions
should always be followed, including the following:
1. Read all instructions.
2. To avoid risk of electrical shock, do not put Stand Mixer in
water or other liquid.
3. This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children
without supervision.
4. Unplug Stand Mixer from outlet when not in use, before
putting on or taking off parts, and before cleaning.
5. Avoid contacting moving parts. Keep hands, hair, and clothing,
as well as spatulas and other utensils away from beater during
operation to reduce the risk of injury to persons and/or
damage to the Stand Mixer.
6. Do not operate Stand Mixer with a damaged cord or plug or
after the Stand Mixer malfunctions, or is dropped or damaged
in any manner. Return appliance to the nearest Authorized
Service Center for examination, repair or electrical or
mechanical adjustment.
7. The use of attachments not recommended or sold by
W10648168A_ENv03.indd 6 12/11/13 11:48 AM
English
7
STAND MIXER SAFETY
STAND MIXER SAFETY
SAVE THESE INSTRUCTIONS
KitchenAid may cause re, electrical shock, or injury.
8. Do not use the Stand Mixer outdoors.
9. Do not let the cord hang over edge of table or counter.
10. Remove Flat Beater, Stainless Steel Whip, or Spiral Dough
Hook from Stand Mixer before washing.
11. To avoid product damage, do not use the mixer bowls in
areas of high heat such as an oven, microwave, or on a
stovetop.
12. This product is designed for household use only.
Volts: 220-240 A.C.
Hertz: 50/60 Hz
Wattage: 315 Watts for model 5KPM5
500 Watts for models
5KSM7580X, 5SM7591X,
and 5KSM6521X
NOTE: The power rating for your Stand
Mixer is printed on the serial plate, placed
under your Stand Mixer.
Do not use an extension cord. If the power
supply cord is too short, have a qualied
electrician or serviceman install an outlet
near the appliance.
The wattage rating is determined by using
the attachment that draws the greatest load
(power). Other recommended attachments
may draw signicantly less power.
Electrical requirements
Disposal of packing material
The packing material is 100% recyclable
and is marked with the recycle symbol .
The various parts of the packing must
therefore be disposed of responsibly
and in full compliance with local authority
regulations governing waste disposal.
Scrapping the product
- This appliance is marked in compliance
with European Directive 2002/96/EC, Waste
Electrical and Electronic Equipment (WEEE).
- By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise
be caused by inappropriate waste handling
of this product.
- The symbol on the product or on the
accompanying documentation indicates
that it should not be treated as domestic
waste but must be taken to an appropriate
collection centre for the recycling of
electrical and electronic equipment.
For more detailed information about
treatment, recovery and recycling of this
product, please contact your local city ofce,
your household waste disposal service or the
shop where you purchased the product.
Electrical equipment waste disposal
W10648168A_ENv03.indd 7 12/11/13 11:48 AM
8
PARTS AND FEATURES
Speed control
lever
Bowl lift lever
(not shown)
Beater Shaft
Wire whip*
Bowl*
Dough hook*
Flat beater*
Locating pins
Bowl support
Beater height
adjustment
screw
Motor head
Bowl
handle*
Attachment hub
(see the “Attachments*”
section)
Attachment
knob
Pouring shield**
* Material, style, and size may differ depending on model.
** Pouring shield included only for models 5KPM5, 5KSM7580X and 5KSM7591X / Lid included only
for models 5KPM5 and 5KSM6521X.
Lid**
W10648168A_ENv03.indd 8 12/11/13 11:48 AM
English
9
PARTS AND FEATURES
Wire whip*
ASSEMBLING THE STAND MIXER
Locating Pin
Spring Latch
Pouring
Chute
1
Turn speed control to “0” (OFF), and
unplug Stand Mixer.
Attaching the bowl and beaters
2
Place bowl lift lever into down position.
3
Fit bowl supports over locating pins;
press down on back of the bowl until
bowl pin snaps into the spring latch. If
not securely snapped into place, bowl
will be unstable and wobble during use.
5
If using the pouring shield*, from the
front of the Stand Mixer, slide the
pouring shield over the bowl until it
is centered. The bottom rim of the
pouring shield should fit within the bowl.
4
Slip a beater (flat, wire whip, or dough
hook) onto the beater shaft and press
upward as far as possible. Turn beater to
the right, hooking it over the pin on the
beater shaft.
NOTE: Rotate the pouring shield* so the
motor head covers the U-shaped gap in
the shield. The pouring chute will be just
to the right of the attachment hub as you
face the Stand Mixer.
* Pouring shield included only for models 5KPM5, 5KSM7580X and 5KSM7591X
6
Raise the bowl into mixing position
by rotating the bowl lift lever
counterclockwise to the straight up
position. The bowl must always be
in the raised position when mixing.
W10648168A_ENv03.indd 9 12/11/13 11:48 AM
10
ASSEMBLING THE STAND MIXER
NOTE: When properly adjusted, the at
beater will not strike on the bottom or
side of the bowl. If the at beater or the
wire whip is so close that it strikes the
bottom of the bowl, the coating may wear
off the at beater (for coated beaters) or
wires on the wire whip may wear.
Scraping sides of bowl may be necessary
under certain conditions regardless of
beater adjustment. The Stand Mixer must
be stopped to scrape bowl or damage to
Stand Mixer may occur.
Adjusting beater to bowl clearance
Your Stand Mixer is adjusted at the factory so the at beater just clears the bottom of the
bowl. If, for any reason, the at beater hits the bottom of the bowl or is too far away from
the bowl, you can correct the clearance easily.
2
Lower the bowl to the down position.
3
Turn beater height adjustment screw (A)
slightly counterclockwise (left) to raise
the flat beater; or turn clockwise (right)
to lower the flat beater. Adjust so that
the flat beater just clears the surface of
the bowl. If you over adjust the screw,
the bowl lift lever may not lock in place.
1
Turn speed control to “0” (OFF), and
unplug Stand Mixer.
W10648168A_ENv03.indd 10 12/11/13 11:48 AM
English
11
ASSEMBLING THE STAND MIXER
OPERATING THE STAND MIXER
All speeds have the Soft Start feature that
automatically starts the Stand Mixer at
a lower speed to help avoid ingredient
splash-out and “our puff” at start-up,
then quickly increases to the selected
speed for optimal performance.
Speed Used for Accessories Description
1 Stirring For slow stirring, combining, mashing,
starting all mixing procedures. Use to
add our and dry ingredients to batter,
and add liquids to dry ingredients. Do
not use Speed 1 to mix or knead
yeast doughs.
2 Slow mixing, For slow mixing, mashing, faster stirring.
Kneading Use to mix and knead yeast doughs,
heavy batters, and candies; start mashing
potatoes or other vegetables; cut
shortening into our; mix thin or
splashy batters.
4 Mixing, For mixing semi-heavy batters, such
Beating as cookies. Use to combine sugar and
shortening and to add sugar to egg
whites for meringues. Medium speed
for cake mixes.
6 Beating, For medium-fast beating (creaming)
Creaming or whipping. Use to nish mixing cake,
doughnut, and other batters. High
speed for cake mixes.
8-10 Fast beating, For whipping cream, egg whites, and
Whipping, boiled frostings. For whipping small
Fast whipping amounts of cream, egg whites or for
nal whipping of mashed potatoes.
NOTE: Use Speed 2 to mix or knead yeast doughs. Use of any other speed creates high
potential for Stand Mixer failure. The dough hook efciently kneads most yeast dough
within 4 minutes.
Speed control guide - 10 speed Stand Mixers
W10648168A_ENv03.indd 11 12/11/13 11:48 AM
12
Removing the bowl and beaters
OPERATING THE STAND MIXER
1
Turn speed control to “0” (OFF), and
unplug Stand Mixer.
2
Lower the bowl to the down position.
3
Press the beater up as far as possible
and turn left, then pull beater from
the beater shaft.
4
Grasp the bowl handle and lift it straight
up and off the locating pins.
TIPS FOR GREAT RESULTS
Stand Mixer use
PERSONAL INJURY HAZARD
To avoid personal injury and
damage to the beater, do not
attempt to scrape bowl while
mixer is operating; turn mixer
off. Should scraper or other
object drop into bowl, turn
motor OFF before removing.
The bowl and beater are designed to provide
thorough mixing without frequent scraping.
Scraping the bowl once or twice during
mixing is usually sufcient.
The Stand Mixer may become warm during
use. Under heavy loads with extended
mixing time periods, you may not be able
to comfortably touch the top of the Stand
Mixer. This is normal.
W10648168A_ENv03.indd 12 12/11/13 11:48 AM
English
13
Mixing time
Your KitchenAid Stand Mixer will mix
faster and more thoroughly than most
other electric mixers. Therefore, the
mixing time in most recipes must be
adjusted to avoid overbeating.
To help determine the ideal mixing time,
observe the batter or dough and mix only
until it has the desired appearance described
in your recipe, such as “smooth and creamy.”
To select the best mixing speeds, use the
“Speed control guide” section.
NOTE: If ingredients in very bottom
of bowl are not thoroughly mixed,
then the beater is not far enough into
the bowl. See the “Setting up your
Stand Mixer” section.
Adding Ingredients
Always add ingredients as close to side of
bowl as possible, not directly into moving
beater. The Pouring Shield can be used to
simplify adding ingredients. Use Speed 1
until ingredients have been blended. Then
gradually increase to desired speed.
Adding Nuts, Raisins, or Candied Fruits
Follow individual recipes for guidelines on
including these ingredients. In general, solid
materials should be folded in the last few
seconds of mixing on Speed 1. The batter
should be thick enough to keep the fruit
or nuts from sinking to the bottom of the
pan during baking. Sticky fruits should be
dusted with our for better distribution
in the batter.
TIPS FOR GREAT RESULTS
Mixing tips
Liquid Mixtures
Mixtures containing large amounts of liquid
ingredients should be mixed at lower speeds
to avoid splashing. Increase speed only after
mixture has thickened.
KitchenAid optional attachments are designed to assure long life. The attachment power
shaft and attachment hub socket are of a square design, to eliminate any possibility of slipping
during the transmission of power to the attachment. The hub and shaft housings are tapered
to assure a snug t, even after prolonged use and wear. KitchenAid attachments require no
extra power unit to operate them; the power unit is built-in.
Hub cover**
Attachment
knob
Attachment* housing
Attachment* shaft housing
Pin
Notch
Attachment
hub socket
Attachment* power shaft
* Optional attachment, not part of the mixer.
** Style may vary depending on model.
ATTACHMENTS
W10648168A_ENv03.indd 13 12/11/13 11:48 AM
14
CARE AND CLEANING
ELECTRICAL SHOCK HAZARD
ALWAYS BE SURE TO UNPLUG
MIXER BEFORE CLEANING TO
AVOID POSSIBLE ELECTRICAL
SHOCK.
Wipe mixer with a damp cloth.
DO NOT IMMERSE IN WATER.
Wipe off beater shaft frequently,
removing any residue that may
accumulate.
2
The bowl, flat beater, and dough hook
may be washed in a dishwasher. Or,
clean them thoroughly in hot sudsy
water and rinse completely before
drying. Do not store beaters on shaft.
3
IMPORTANT: The wire whip, pouring
shield, and lid are not dishwasher safe.
Clean thoroughly in hot sudsy water
and rinse completely before drying. Do
not store wire whip on shaft.
** Pouring shield included only for models 5KPM5, 5KSM7580X and 5KSM7591X / Lid included only
for models 5KPM5 and 5KSM6521X.
1
Always be sure to unplug Stand Mixer
before cleaning. Wipe Stand Mixer
with a soft, damp cloth. Do not use
household/commercial cleaners. Wipe
off beater shaft frequently, removing
any residue that may accumulate. Do
not immerse in water.
W10648168A_ENv03.indd 14 12/11/13 11:48 AM
English
15
TROUBLESHOOTING
Please read the following before calling
your service center.
1. The Stand Mixer may warm up during
use. Under heavy loads with extended
mixing time periods, you may not be able
to comfortably touch the top of the unit.
This is normal.
2. The Stand Mixer may emit a pungent odor,
especially when new. This is common with
electric motors.
3. If the Flat Beater hits the Bowl, stop the
Stand Mixer. See the “Setting Up Your
Stand Mixer” section.
If your Stand Mixer should malfunction
or fail to operate, please check the
following:
- Is the Stand Mixer plugged in?
- Is the fuse in the circuit to the Stand Mixer
in working order? If you have a circuit
breaker box, be sure the circuit is closed.
- Turn off the Stand Mixer for 10-15 seconds,
the turn it back on. If the mixer still does
not start, allow it to cool for 30 minutes
before turning it back on.
- If the problem is not due to one of the
above items, see the “Customer service”
section.
W10648168A_ENv03.indd 15 12/11/13 11:48 AM
16
WARRANTY AND SERVICE
Length of
Warranty:
KitchenAid Will Pay
For:
KitchenAid Will Not
Pay For:
Europe, Middle East
and Africa:
For models
5KPM5, and
5KSM7591X: One year
full warranty from date
of purchase.
For models 5KSM7580X,
5KSM6521X:
Five years full warranty from
date of purchase.
The replacement
parts and repair labor
costs to correct
defects in materials
or workmanship.
Service must
be provided by
an Authorized
KitchenAid Service
Center.
A. Repairs when Stand Mixer
is used for operations other
than normal household
food preparation.
B. Damage resulting from
accident, alterations, misuse,
abuse, or installation/operation
not in accordance with local
electrical codes.
KITCHENAID DOES NOT ASSUME ANY RESPONSIBILITY FOR INDIRECT
DAMAGES.
KitchenAid Stand Mixer warranty
www.KitchenAid.eu
Customer service
© 2013. All rights reserved.
Specications subject to change without notice.
In U.K. and Ireland:
For any questions, or to nd the nearest KitchenAid Authorized Service Center, please nd
our contact details below.
NOTE: All service should be handled locally by an Authorized KitchenAid Service Center.
Contact number for U.K. and Northern Ireland:
Tollfree number 0800 988 1266 (calls from mobile phones are charged standard
network rate)
Contact number for Ireland:
Tollfree number +44 (0) 20 8616 5148
E-mail contact for U.K. and Ireland:
Go to www.kitchenaid.co.uk, and click on the link “Contact Us” at the bottom of the page.
Address for U.K. and Ireland:
KitchenAid Europa, Inc.
PO BOX 19
B-2018 ANTWERP 11
BELGIUM
In other countries:
For all product related questions and after sales matters, please contact your dealer
to obtain the name of the nearest Authorized KitchenAid Service/Customer Center.
W10648168A_ENv03.indd 16 12/11/13 11:48 AM
English
17
W10648168A_ENv03.indd 17 12/11/13 11:48 AM
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
KitchenAid 4KSMC50S User manual
-
-
KitchenAid 5KSM3311XBAC User guide
-
-
-
KitchenAid Stand Mixer Instructions Manual
-
-
-
-