TOTALINE HUMCCLFP1218 Owner's manual

Brand: TOTALINE

Model: HUMCCLFP1218

Category: Humidifiers

Type: Owner's manual

This manual is also suitable for

Part Number P110-LFP1025A, P110-WTR2019A,

P110-LBP2018A, P110-SFP1016A,

P110-SBP2017A

GENERAL

Congratulations on your excellent choice in this addition

to your home comfort system.

Your humidiﬁer represents both the latest in engineering

development and the culmination of many years of experi-

ence from one of the most reputable manufacturers of com-

fort systems.

Your new unit is among the most energy-efficient and

reliable home humidiﬁers available today. To assure its

dependability, spend a few minutes now with this booklet.

Learn about the operation of your humidiﬁer and the small

amount of maintenance it takes to keep it operating at peak

efficiency.

During the heating season, your home can become un-

comfortably dry. This is because cold winter air holds very

little moisture. When outdoor air is warmed to average room

temperature, its relative humidity falls to even lower levels.

Proper humidity control can alleviate problems caused by

excessive dryness. The additional moisture supplied by your

humidiﬁer may enable you to reduce the temperature setting

on your thermostat — without any loss of indoor comfort.

Your humidiﬁer adds water to the air inside your home.

Although the rate of humidiﬁcation is variable, it may ex-

ceed one-half gallon of water per hour. The typical process

of humidiﬁcation begins when water ﬂows through the hu-

midiﬁer valve and soaks the large evaporator pad. Hot, dry

air from the furnace passes through the pad and absorbs the

water. Then, this moisture-laden air is distributed through-

out the house via the ductwork. See Fig. 1. Typical humidi-

ﬁer installations are shown in Fig. 2.

OPERATING YOUR HUMIDIFIER

Your new humidiﬁer is designed to operate as part of your

home heating system. For performance at maximum effi-

ciency, follow these recommendations:

• The humidiﬁer is controlled by a humidistat. Adjust the

humidistat setting according to the outside temperature. Re-

fer to Table 1 as a general guide. If after several days, the

air in your home is too moist, lower the humidistat setting.

Condensation on single-pane windows indicates exces-

sive moisture. If the air is too dry, increase the setting.

• Continuous blower operation provides for constant hu-

midiﬁcation. Continuous blower operation also minimizes

temperature differences throughout the home. Further-

more, a system equipped with an electronic air cleaner of-

fers the added beneﬁt of full-time air ﬁltration.

• Supply- and return-air grilles should not be blocked by drapes,

furniture, or other objects. Restricted airﬂow reduces the

efficiency of the humidiﬁer, as well as that of the whole

comfort system.

• The humidiﬁer unit must be properly maintained on a regu-

lar basis.

Table 1 — Humidistat Settings

OUTSIDE

TEMPERATURE

(°F)

RECOMMENDED

HUMIDISTAT SETTING

(% RELATIVE HUMIDITY)

−20 15

−10 20 (LOW)

−0 25

10 30

20 35

30 40 (MED)

OWNER’S

MANUAL

Residential

Humidiﬁer

DRY

AIR

EVAPORATOR

PAD

HUMIDIFIED

AIR

DRAIN

Fig. 1 — Humidiﬁer Operation

Fig.2—Typical Humidiﬁer Installations

Manufacturer reserves the right to discontinue, or

change at any time, speciﬁcations or designs

without notice and without incurring obligations.

REPLACEMENT COMPONENTS DIVISION LITERATURE NUMBER HUM-50SO

R CARRIER CORPORATION 1/99 REPLACES 2-05930

PRINTED IN U.S.A.

Start-Up Procedures

1. Open the saddle valve on the water supply line. (See

Fig. 3.) Set humidistat to the desired relative humidity.

(See Fig. 4 and Table 1.)

2. Turn the furnace on and adjust the thermostat to a high

temperature setting. Be sure that the furnace blower is

operating.

3. Check to see if water is ﬂowing into the humidiﬁer.

• On P110-L8P2018A or P110-LFP1025A humidiﬁers,

loosen the thumbscrew that holds the distributor cover

to the top of the cabinet. Lift up the distributor cover

slightly to make certain that water is ﬂowing from the

solenoid valve into the distributor pan. Do not lift the

cover off the cabinet more than 1 in. when water is ﬂow-

ing. (See Fig. 5 or 6.)

• On a P110-SBP2017Ahumidiﬁer, gently pull the latch

that secures the access door. Remove the door. Check

to see if water is ﬂowing from the solenoid valve into

the evaporator pad. (See Fig. 7.)

• On a P110-SFP1016A humidiﬁer, open the side door

or the front cover. If the front cover is opened, hold the

pad assembly in place. Check to see if water is ﬂowing

from the solenoid valve into the distributor pan. (See

Fig. 8.)

• On a P110-WTR2019Ahumidiﬁer, look through the win-

dow on front of the unit to see that the evaporator pad

is rotating and water is ﬂowing. (See Fig. 9.)

The P110-WTR2019Ahumidiﬁer is controlled by a float

valve. Turning off the furnace will not affect the water

ﬂow until ﬂoat level is achieved.

4. Turn off the furnace. When the blower stops, look into

the humidiﬁer to make sure the water is not ﬂowing into

the unit.

5. Replace the cover assembly and fasten securely.

6. Now, turn the furnace on and set the thermostat for de-

sired room temperature.

Fig. 3 — Saddle Valve

HUMIDISTAT

Fig. 4 — Humidistat

DISTRIBUTOR COVER

SOLENOID VALVE

DISTRIBUTOR PAN

EVAPORATOR PAD

CABINET

BOTTOM ACCESS

PANEL

Fig. 5 — Humidiﬁer Details — P110-LBP2018A

SOLENOID VALVE

DISTRIBUTOR COVER

DISTRIBUTOR PAN

EVAPORATOR PAD

CABINET

BOTTOM ACCESS PANEL

Fig. 6 — Humidiﬁer Details — P110-LFP1025A

CABINET

RECTIFIER

DRAIN

INLET

DISTRIBUTOR

PAN

EVAPORATOR

PAD

DUCT

HOUSING

SIDE

ACCESS

DOOR

SOLENOID

VALVE

Fig. 7 — Humidiﬁer Details — P110-SBP2017A

Shutdown Procedures — To shut down your humidi-

ﬁer, close the saddle valve on the water line. Then turn off

the humidistat. When set to the OFF position, the humidistat

shuts off the electrical power to the solenoid valve on the

humidiﬁer.

NOTE: If your home comfort system includes cooling, be

sure the water supply to your humidiﬁer is turned off during

the cooling season. Close the damper located in the bypass

duct if one is installed. If your humidiﬁer is a part no. P110-

WTR2019A, drain and clean the water pan as described in

cleaning procedures.

PERFORMING ROUTINE MAINTENANCE

With the proper maintenance and care, your humidiﬁer will

operate economically and dependably. Maintenance can be

accomplished easily by referring to the following directions.

However, before performing any maintenance, consider these

important safety precautions:

Disconnect all electrical power to the humidiﬁer and fur-

nace before performing any service or maintenance to

avoid personal injury or death.

NOTE: There may be more than one electrical disconnect

switch.

Although special care has been taken to minimize sharp

edges in the construction of your humidiﬁer, be ex-

tremely careful when handling parts or reaching into the

unit to avoid personal injury.

Your humidiﬁer has been designed for easy disassembly

to simplify cleaning and servicing. Your unit must be kept

clean to maintain its efficiency.

Regular inspection allows you to determine the cleaning

schedule best suited to your humidiﬁer’s operating condi-

tions. The frequency for required maintenance will depend

most upon the available water supply. In areas where hard

water and high mineral content are prevalent, more frequent

cleaning and servicing may be required.

At minimum, the humidiﬁer will need to be cleaned at the

beginning of every heating season.

Cleaning Procedures

P110-LBP2018A, P110-SBP2017A, P110-LFP1025A, AND

P110-SFP1016A HUMIDIFIERS

1. Turn off all electrical power to the humidiﬁer and furnace

or fan coil.

2. Turn off the humidiﬁer’s water supply. (See Fig. 3.)

3. Disassemble the humidiﬁer.

• To disassemble a P110-SBP2017A humidiﬁer, gently

pull the latch that secures the access panel. Remove the

door and slide the evaporator pad assembly out of the

unit. (See Fig. 7.)

• To disassemble either a P110-LBP2018A or P110-

LFP1025Ahumidiﬁer, ﬁrst remove the water supply con-

nection to the solenoid valve. Next, remove the screw

that holds the distributor cover to the cabinet, and lift

off the cover. Disconnect the drain line from the sump

and loosen the thumbscrews(s) holding the sump to the

cabinet. Remove the sump. Remove evaporator pad as-

sembly. (See Fig. 5 or 6.)

• To disassemble a P110-SFP1016A humidiﬁer, the pad

assembly can be removed from the side access door or

the front cover. When removing the side door, lift the

pad assembly up by holding the tabs and slide the as-

sembly out. When removing the front cover, discon-

nect the quick connects to the solenoid valve, unscrew

the 4 screws to the front cover, snap loose the top and

bottom catches, and lay the front cover aside. Once the

front cover is off, lift the pad assembly up and twist it

out. The pad assembly consists of 4 parts; the distribu-

tor pan, frame, sump, and the evaporator pad. Pull the

distributor pan apart from the frame and the evaporator

pad can be removed. Do not force the evaporator pad

in or out without removing the distributor pan as this

will distort the pad. See Fig. 8.

4. Clean the humidiﬁer’s external components.

• If your humidiﬁer is a P110-SBP2017Ahumidiﬁer, wash

the access door and outlet drain portion of the cabinet.

Make sure the drain is open.

• If your humidiﬁer is a P110-LBP2018A, P110-SFP-

1016A, or P110-LFP1025A unit, wash the distributor

cover, sump cover, and cabinet. Be sure the inlet ports

are open and clean. Then, clean the sump with a so-

lution of detergent and water.

5. Clean the internal components of your humidiﬁer. Wash

the distributor pan with a mild detergent and warm water.

Be sure holes and slots in the pan are clean and unob-

structed. Wash the evaporator pad assembly in a deter-

gent solution. If there are scale deposits on the pad, soak

CABINET

FRONT COVER

SCREWS (4)

SIDE ACCESS DOOR

PAD ASSEMBLY

SOLENOID VALVE

DISTRIBUTOR PAN

(HIDDEN)

Fig. 8 — Humidiﬁer Details — P110-SFP1016A

BEARING RETAINER

CABINET

PAD

PAN

Fig. 9 — Humidiﬁer Details — P110-WTR2019A

it in ordinary household vinegar. If the pad is covered by

a heavy deposit of scale, or if the local water supply has

high sulfate or calcium content, replace the pad with a

new one. Contact your dealer for replacement part.

6. Reassemble your humidiﬁer.

7. Turn on the electrical power and water supplies. Refer to

the start-up procedures.

P110-WTR2019A HUMIDIFIERS

1. Turn off all electrical power to the humidiﬁer and furnace

or fan coil.

2. Turn off the humidiﬁer’s water supply. (See Fig. 3.)

3. Drain water from the unit. Place a pail underneath the

drain plug located on the bottom of the humidiﬁer cabi-

net. Lift the tab on the drain plug and remove the plug.

Allow all water to drain from the unit. (See Fig. 10.)

4. Remove the front door from the humidiﬁer. Rotate the

latches one-half turn, then pull the door forward.

5. Remove and inspect the evaporator pad assembly. Lift

the bearing from its retainer. (See Fig. 9.) Pull the as-

sembly away from the motor to disengage the assembly

shaft from the motor coupling. Remove assembly through

the access opening.

Inspect the evaporator pad. If the pad is heavily loaded

with scale, or if the local water has a high sulfate content,

replace the pad. Contact your dealer for replacement part.

NOTE: For best performance, the evaporator pad should

be replaced before each heating season.

6. Inspect the ﬂoat assembly. Remove the ﬂoat arm from

the valve body by sliding out the pin and lifting off the

ﬂoat arm. (See Fig. 11.) Inspect the rubber valve seat lo-

cated inside the ﬂoat arm. If the seat appears to be nicked

or worn, invert the seat or replace it with the spare valve

seat located on the ﬂoat arm. Inspect the water opening

in the valve body. If the opening is clogged, use a pin to

remove the obstruction. Remove any accumulated de-

posits from the valve body and ﬂoat arm.

7. Clean the water pan and unit cabinet. Tilt the water pan

and lift it from the unit. Wash the pan with warm, soapy

water. Flex the pan to loosen accumulated scale. Wash

the unit interior, removing any accumulated deposits. In-

spect the drain line to ensure that no blockage has oc-

curred. Clean as required. (See Fig. 10.)

8. Reassemble your humidiﬁer. Reinsert the water pan and

drain plug. Ensure that the overﬂow tube is inserted into

the hole at the bottom of the cabinet. Attach the ﬂoat arm

to the valve body by aligning the holes on both parts and

reinserting the pin. Do not force or bend the pin. The float

arm should have free up-and-down movement. Install the

evaporator pad assembly. Ensure that the square shaft en-

gages the motor coupling and that the bearing washer is

located inside the bearing retainer. Turn the water on. Ad-

just ﬂoat by rotating until water covers inside of foam

drum. Attach the access door and turn the latches.

9. Turn on electrical power supplies. Refer to start-up pro-

cedures listed on page 2.

BEFORE YOU REQUEST A SERVICE CALL

Before You Call For Service, Check For These Eas-

ily Solved Problems:

• Check the main power disconnect switch. Verify that the

circuit beakers are on and that fuses have not blown. If

you must reset breakers or replace fuses, do so only once.

Contact your servicing dealer for assistance if the break-

ers trip or the fuses blow a second time.

• If the humidity level is too low, check the humidistat set-

ting. Conﬁrm that the saddle valve is turned on. Check the

evaporator pad, and clean or replace the pad as necessary.

Check water level in P110-WTR2019A humidiﬁer.

• Check for sufficient airﬂow. Check the furnace ﬁlter or elec-

tronic air cleaner for excessive accumulations of dirt. Check

for blocked return- or supply-air grilles. Be sure grilles are

open and unobstructed.

• If water drips from the humidiﬁer, check the drain hose

for kinks or obstructions. On P110-WTR2019A humidi-

ﬁers, dripping may indicate that the ﬂoat valve requires

adjustment.

• If your comfort system still fails to operate properly, con-

tact your servicing dealer for troubleshooting and repairs.

Specify your apparent problem, and state the model and

serial numbers of your equipment. (You should have them

recorded where noted in this booklet.) With this informa-

tion, your dealer may be able to offer helpful suggestions

over the phone, or safe valuable time through knowledge-

able preparation for the service call.

Regular Dealer Maintenance — In addition to the rou-

tine maintenance that you perform, your humidiﬁer should

be inspected regularly by a properly trained service techni-

cian. The inspection (preferably each year, but at least every

other year) should include the following:

• Routine inspection of the humidiﬁer. Cleaning, if nec-

essary. Cleaning or replacement of the evaporator pad

as required.

• A check of all electrical wiring and connections.

• A check of water connections to the unit.

• Operational check of the complete comfort system to

determine actual working condition. Necessary repair

and/or adjustment should be performed at this time.

Your servicing dealer may offer an economical service

contract that covers seasonal inspections. Ask for further

details.

HUMIDIFIER HOUSING

WATER PAN

OVERFLOW TUBE

DRAIN PLUG

Fig. 10 — Cleaning Water Pan and Unit Cabinet —

P110-WTR2019A

FLOAT ARM

VALVE SEAT

VALVE

BODY

HIGHER

LOWER

Fig. 11 — Float Arm Removal — P110-WTR2019A

SERVICE INFORMATION

Record the model and serial numbers of your new humidiﬁer in the following spaces.

This information, along with the other ready-reference facts requested below, may be

required if you should ever need information or service.

Model No.

Serial No.

Date Installed

Dealer Name

Address

City

State Zip

Telephone

Your Assurance of Quality

ALL Totaline products are backed with a one-year

warranty by Carrier Corporation, the world’s

largestmanufacturer ofair conditioning,heating, and

refrigeration products.

Manufacturer reserves the right to discontinue, or

change at any time, speciﬁcations or designs

without notice and without incurring obligations.

REPLACEMENT COMPONENTS DIVISION LITERATURE NUMBER HUM-50SO

R CARRIER CORPORATION 1/99 REPLACES 2-05930

PRINTED IN U.S.A.

TOTALINE HUMCCLFP1218 Owner's manual

Brand: TOTALINE

Model: HUMCCLFP1218

Category: Humidifiers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

TOTALINE HUMCCLFP1218 Owner's manual

This manual is also suitable for

TOTALINE HUMCCLFP1218 Owner's manual

Other documents