Weber PLATINUM SERIES 2 3400 NG User manual

Brand: Weber

Model: PLATINUM SERIES 2 3400 NG

Category: Barbecues & grills

Type: User manual

This manual is also suitable for

PLATINUM

™

SERIES II

Natural Gas Barbecues

Operating Guide

NOTICE TO INSTALLER: These instructions

must be left with the owner and the owner

should keep them for future use.

WARNING: Follow all leak check

procedures carefully in this manual prior to

barbecue operation. Do this even if

barbecue was dealer assembled.

WARNING: Do not operate this barbecue

without reading the entire operating guide.

THIS GAS APPLIANCE IS DESIGNED FOR

OUTDOOR USE ONLY.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, immediately call your

gas supplier or your fire department.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance.

96176 6/98

Serial Number

Platinum Series II

2200 NG

Serial Number

Platinum Series II

3200 NG

Serial Number

Platinum Series II

3400 NG

A P P R O V E D

CANADIAN

GAS ASSOCIATION

Read before assembly

TABLE OF CONTENTS

Warnings 3

Warranty 4

A Word of Thanks 4

Standards and Codes Information 5

Storage 5

Operating Area 5

Natural Gas Supply Testing 5

*REFER TO YOUR STEP-BY-STEP SECTION AT

THIS TIME

Lighting 6

Crossover Ignition System 6

To Extinguish 6

Manual Lighting 7

To Extinguish 7

Lighting the Side Burner 8

Cooking 9

Cleaning 9

Using the Steam-N-Chips Smoker 10

Cleaning the Steam-N-Chips Smoker 10

Maintenance 11-13

Spider Stopper Guards 11

Inspection and Cleaning of the

Spider Stopper Guards 11

Main Burner Flame Pattern 12

Main Burner Cleaning Procedure 12

Replacing the Main Burners 12

Crossover Ignition System Operations 13

Troubleshooting 14

Side Burner Troubleshooting 15

Side Burner Maintenance 16-17

To Clean the Burner Head 17

To Reassemble the Burner Head 17

Exploded Views and Replacement

Parts List 18-23

Platinum Series II 2200 NG 18-19

Platinum Series II 3200 NG 20-21

Platinum Series II 3400 NG 22-23

Patents and Trademarks 24

WARNINGS

DANGER

Failure to follow the Dangers,Warnings and Cautions contained in this Owner’s Manual may

result in serious bodily injury or death, or a fire or an explosion causing damage to property.

■ Do not store a spare or disconnected LP tank under or

near this barbecue.

■ Improper assembly may be dangerous. Please

carefully follow the assembly instructions in

this manual.

■ After a period of storage, and/or nonuse, the

Weber Gas Barbecue should be checked for gas

leaks and burner obstructions before using. See

instructions in this manual for correct procedures.

■ Do not operate the Weber Gas Barbecue if there

is a gas leak present.

■ Do not use a flame to check for gas leaks.

■ Combustible materials should never be within 24

inches of the top, bottom, back or sides of your

Weber Gas Barbecue.

■ Do not put a barbecue cover or anything flammable

on or in the storage area under the barbecue.

■ Your Weber Gas Barbecue should never be used

by children.

■ You should exercise reasonable care when

operating your Weber Gas Barbecue. It will be hot

during cooking or cleaning, and should never be

left unattended.

■ Should the burners go out during operation, turn

all gas valves off. Open the lid and wait five

minutes before attempting to relight, using the

lighting instructions.

■ Do not use charcoal or lava rock in your Weber

Gas Barbecue.

■ Never lean over open grill or place hands or

fingers on the front edge of the cooking box.

■ Should a grease fire occur, turn off all burners and

leave lid closed until fire is out.

■ Do not enlarge valve orifices or burner ports when

cleaning the valves or burners.

■ The Weber Gas Barbecue should be thoroughly

cleaned on a regular basis.

■ LP gas is not natural gas. The conversion or

attempted use of natural gas in an LP unit or LP

gas in a natural gas unit is dangerous and will

void your warranty.

■ Do not attempt to disconnect any gas fitting while

your barbecue is in operation.

■ Use heat-resistant barbecue mitts or gloves when

operating barbecue.

■ This barbecue is for residential use only.

STANDARDS AND CODES INFORMATION

Your Weber Gas Barbecue is a portable outdoor cooking

appliance. With the Weber Gas Barbecue you can grill,

barbecue, roast and bake with results that are difficult to

duplicate with indoor kitchen appliances. The closed lid

and Flavorizer Bars produce that "outdoor" flavor in the

food.

The Weber Gas Barbecue is portable so you can easily

change its location in your yard or on your patio.

Portability means you can take your Weber Gas

Barbecue with you if you move.

The natural gas supply is easy to use and gives you more

cooking control than charcoal fuel.

■ These instructions will give you the minimum

requirements for operating and maintaining your

Weber Gas Barbecue. Please read the instructions

carefully before using your Weber Gas Barbecue.

Improper assembly can be dangerous.

■ Not for use by children.

■ If there are local codes that apply to portable gas

grills, you will have to conform to them. If there are no

local codes, you must conform to the latest edition of

the National Fuel Gas Code: ANSI Z 223.1.

■ This Weber Gas Barbecue is designed for natural

(piped in city) gas only. Do not use Liquid Propane

(LP) bottled gas.The valves, orifices and hose are for

natural gas only.

■ Do not use with charcoal fuel.

■ The Weber Gas Barbecue should be checked for gas

leaks and any obstructions in the burner tubes before

using. (See Maintenance Section.)

■ Check that the areas under the control panel and the

bottom tray are free from debris that might obstruct

the flow of combustion or ventilation air. (See

Maintenance Section.)

For Installation in Canada

These instructions, while generally acceptable, do not

necessarily comply with the Canadian Installation codes,

particularly with piping above and below ground. In Canada

the installation of this appliance must comply with local

codes and/or Standard CAN/CGA-B149.1 (Installation

Code for Natural Gas Burning Appliances and Equipment).

Storage

■ The gas must be turned OFF at the natural gas

supply when the Weber Gas Barbecue is not in use.

■ When storing the Weber Gas Barbecue, make sure

that the inside shut off valve and/or locking outdoor

shut off valve is secured in the OFF position. When

the Weber Gas Barbecue is stored indoors, the gas

supply MUST BE DISCONNECTED.

■ After a period of storage and/or nonuse the Weber

Gas Grill should be checked for gas leaks and any

obstructions in the burner tubes before using. Refer

to Maintenance Section.

■ Check that the areas under the control panel and the

bottom tray are free from debris that might obstruct

the flow of combustion or ventilation air.

■ The Spider Stopper Guards should also be checked

for any obstructions. Refer to Maintenance Section.

Operating Area

WARNING: Only use this barbecue outdoors in a

well ventilated area. Do not use in a garage,

building,breezeway or any other enclosed area.

■ Never use your Weber Gas Barbecue under an

unprotected combustible roof or overhang.

■ Your Weber Gas Barbecue is not intended to be

installed in or on recreational vehicles and/or boats.

■ Keep this grill away from combustible materials when

in use at a minimum of 24 inches of the top, bottom,

back or sides.

■ The entire cooking box gets hot when in use. Do not

leave unattended.

■ Keep any electrical supply cord and the fuel supply

hose away from any heated surface.

■ Keep the cooking area clear of flammable vapors

and liquids, such as gasoline, alcohol, etc., and

combustible materials.

Natural Gas Supply Testing

■ Disconnect your Weber Gas Barbecue when the gas

supply is being tested at high pressures. This

appliance and its individual shutoff valve must be

disconnected from the gas supply piping system

during any pressure testing of that system at test

pressures in excess of 1/2 psig (3.5 kPa).

■ Turn off your Weber Gas Barbecue when the gas

supply is being tested at low pressures. This appliance

must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at the

pressure equal to or less than 1/2 psig (3.5 kPa).

REFER TO YOUR STEP-BY-

STEP SECTION AT THIS TIME

FOR BARBECUE ASSEMBLY

WARNING: Make sure your barbecue is assembled

properly and leak checked before attempting to operate.

Thank you for choosing a Weber Barbecue. Our family here at Weber has worked hard to produce the

highest quality products for your satisfaction. While we give much attention to our products, an occasional

error may occur. Our knowledgeable Customer Service staff is prepared to help you with any problems with

parts or assembly. Call our toll free number. For quicker service, please have your owner’s manual and

serial number available for reference. We also welcome any comments or suggestions you might have

regarding our products. We wish you the best in outdoor cooking enjoyment.

Weber-Stephen Products Company

Customer Service Center

250 South Hicks Road

Palatine, IL 60067-6241

(800) 446-1071

A WORD OF THANKS

Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Barbecue

that it will be free of defects in material and workmanship from the date of purchase as follows:

Aluminum Castings, 10 years,

Cooking Grates, 3 years,

Flavorizer Bars, 5 years,

All Remaining Parts, 5 years,

when assembled and operated in accordance with the printed instructions accompanying it.

Weber may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR SALES

SLIP OR INVOICE.

This Limited Warranty shall be limited to the repair or replacement of parts which prove defective under normal use and

service and which on examination shall indicate, to Weber's satisfaction, they are defective. Before returning any parts,

contact Weber-Stephen Products Co. Customer Service Center. If Weber confirms the defect and approves the claim,

Weber will elect to replace such parts without charge. If you are required to return defective parts, transportation charges

must be prepaid. Weber will return parts to the purchaser, freight or postage prepaid.

This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration,

misapplication, vandalism, improper installation or improper maintenance or service, or failure to perform normal and

routine maintenance, including but not limited to damage caused by insects within the burner tubes, as set out in this

owner's manual.

Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes, acid rain,

discoloration due to exposure to chemicals either directly or in the atmosphere, is not covered by this Limited Warranty.

There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability

and fitness are limited in duration to the period of coverage of this express written Limited Warranty. Some states do not

allow limitation on how long an implied warranty lasts, so this limitation may not apply to you.

Weber is not liable for any special, indirect or consequential damages. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.

Weber does not authorize any person or company to assume for it any other obligation or liability in connection with the

sale, installation, use, removal, return, or replacement of its equipment; and no such representations are binding on Weber.

This Warranty applies only to products sold at retail.

WARRANTY

LIGHTING THE MAIN BURNERS

WARNING: Check hose before each use of

barbecue for nicks, cracking, abrasions or cuts. If the

hose is found to be damaged in any way, do not use

the barbecue. Replace using only Weber authorized

replacement hose. Order from Weber-Stephen

Products Co., Customer Service or authorized dealer.

1) Open the lid. Figure 1.

2) Make sure all burner control knobs are OFF. (Push

each burner control knob down and turn clockwise.)

For barbecues equipped with a side burner, push the

burner control knob in and turn clockwise to OFF.

3) Turn gas supply valve on.

WARNING: Do not lean over open barbecue. Keep

your face and body at least one foot away from the

matchlight hole when lighting the barbecue.

4) Push Front burner control knob down and turn to

START/HI.

5) Push the Crossover Ignition Button several times, so

it clicks each time.

6) Check that the burner is lit by looking through the

matchlight hole in the front of the cooking box. (For

closed cart models, open the right door to access

the matchlight hole.)

WARNING: If the burner does not light, turn the

FRONT burner control knob to OFF and wait 5

minutes to let the gas clear before you try again or try

to light with a match.

7) After the FRONT burner is lit you can turn on the

other burners.

Note - Always light the FRONT burner first.The other

burners ignite from the FRONT burner.

TO EXTINGUISH

Turn gas supply OFF at the source, then push down

and turn each burner control knob clockwise to OFF.

Crossover Ignition System

Note - The Crossover Ignition System ignites the Front

burner with a spark from the igniter electrode inside the

Gas Catcher Ignition Chamber.You generate the energy

for the spark by pushing the Crossover Ignition Button

until it clicks.

Figure 1

DANGER

Failure to open sliding work surfaces

while igniting the barbecue, or not waiting 5

minutes to allow the gas to clear if the

barbecue does not light, may result in an

explosive flame-up which can cause serious

bodily injury or death.

Summary lighting instructions are on the control panel.

MANUAL LIGHTING

1) Open the lid. Figure 2.

2) Make sure all burner control knobs are turned OFF.

(Push each burner control knob down and turn

clockwise.)

For barbecues equipped with a side burner, push the

burner control knob in and turn clockwise to OFF.

3) Turn gas supply valve on.

4) Strike a match and put the flame into the matchlight

hole in the front of the cooking box. (For closed cart

models, open the right door to access the

matchlight hole.)

WARNING: Do not lean over open barbecue. Keep

your face and body at least one foot away from the

matchlight hole when lighting the barbecue.

5) Push Front burner control knob down and turn to

H (high).

6) Check that the burner is lit by looking through

matchlight hole on the front of the cooking box. (For

closed cart models, open the right door to access

the matchlight hole.)

WARNING: If the burner does not light, turn the

Front burner OFF and wait 5 minutes to let the gas

clear before you try again or try to light with a match.

7) After the Front burner is lit you can turn on the

other burners.

Note: Always light the FRONT burner first.The other

burners ignite from the FRONT burner.

TO EXTINGUISH

Turn gas supply OFF at the source, then push down

and turn each burner control knob clockwise to OFF.

DANGER

Failure to open lid while igniting the

barbecue, or not waiting 5 minutes to allow the

gas to clear if the barbecue does not light, may

result in an explosive flame-up which can cause

serious bodily injury or death.

Figure 2

The side burner has a separate ignition system from the

main cooking box.

Lighting only the side burner. Figure 3.

1) Open the side burner lid.

2) Check that the side burner valve is OFF (push in and turn

clockwise), and all main burner control knobs are OFF

(push down and turn clockwise).

3) Turn the gas supply on.

4) Push in and turn the side burner control knob to HI.

5) Push the side burner igniter button several times so it

clicks each time.

Figure 3

DANGER

Failure to open lid while igniting the side

burner, or not waiting 5 minutes to allow gas

to clear if the side burner does not light,

may result in an explosive flame-up which

can cause serious bodily injury or death.

LIGHTING THE SIDE BURNER

For the Platinum Series II 3200 & 3400

CAUTION: Side burner flame may be difficult to see

on a bright sunny day.

WARNING: If the side burner does not light:

a) Turn off the side burner control valve.

b) Wait 5 minutes to let the gas clear before you try

again or try to light with a match.

WARNING: The container and contents used on

the side burner should not exceed a maximum of

50 pounds. The diameter should not exceed

14 inches in diameter.

COOKING

The Weber Gas Barbecue should not be moved when

operating or hot.

If burners go out during cooking, open lid, turn off all

burners and wait 5 minutes before relighting.

Note: The temperatures inside your cooking box, for the

first few uses, while surfaces are still very reflective, may

be hotter than those shown in your cookbook. Cooking

conditions may require the adjustment of the burner

controls to attain the correct cooking temperatures.

CAUTION: Replace thermometer in lid when not in

use. Do not leave thermometer in food while cooking.

CAUTION: Check the bottom tray for grease build-

up before each use. Remove excess grease to avoid a

grease fire in the bottom tray.

Refer to your cookbook for detailed charts, cooking

instructions and recipes. If you did not receive your

cookbook, please call our Customer Service Center toll

free at (800) 446-1071.

CAUTION: Turn your Weber Gas Barbecue OFF and

wait for it to cool before cleaning.

CAUTION: Do not clean your Flavorizer Bars or

cooking grates in a self-cleaning oven. Replacement

cooking grates and Flavorizer Bars are available

through your retailer or the Weber-Stephen Customer

Service Center.

Outside surfaces - Use a warm soapy water solution.

CAUTION: Do not use oven cleaner, abrasive

cleansers (kitchen cleansers) cleaners that contain

citrus products or abrasive cleaning pads on barbecue

or cart surfaces.

Bottom tray - Remove excess grease and then wash with

warm soapy water.

WARNING: Use heat-resistant barbecue mitts or

gloves when cleaning the cooking grates and

Flavorizer bars.

Flavorizer Bars and Cooking Grates- Clean with a

suitable brass bristle brush. As needed, remove from grill

and wash with warm soapy water.

Flavorizer Bars and Cooking Grates (alternate

method) - After pre-heating the grill, prior to cooking, brush

the cooking grates with a brass wire brush or crumpled

aluminum foil.

After cooking, turn all main burners on HIGH and let grill

heat for 10 minutes, Brush cooking grates and Flavorizer

bars with a brass wire brush.

Catch pan - Disposable foil trays are available, or you can

line the catch pan with aluminum foil. To clean the catch

pan, wash with warm soapy water.

Thermometer - Wipe with warm soapy water, clean with

plastic scrub ball. Do not put in dishwasher or submerge

in water.

Inside cooking box - Brush any debris off of burners tubes.

DO NOT ENLARGE BURNER PORTS (OPENINGS). Wash

inside of cooking box with warm soapy water.

Inside Lid - While lid is warm, wipe inside with paper towel

to prevent flaking due to grease build-up.

Stainless steel surfaces - Wash with soap and water and

a soft cloth.

CLEANING

The Steam-N-Chips Smoker cooks with both Weber

FireSpice Wood Chips and Chunks. For best results with

faster cooking foods like steaks, burgers and chops, etc.,

we recommend using the FireSpice Chips because they

ignite and create smoke faster. For longer cooking foods

such as roasts, chicken and turkeys, etc., we recommend

using FireSpice Chunks because they ignite slowly and

provide smoke for a longer period of time. As you gain

experience in using your Steam-N-Chips Smoker, we

encourage you to experiment with different combinations of

FireSpice Chips and Chunks to find the smoke flavor that

best suits your taste.

To use the Steam-N-Chips Smoker

As a starting point, place a handful of FireSpice Chips or a

few FireSpice Chunks in the bottom of the smoker body.

Figure 4. Since the chunks vary in size, place as many as

you can in the smoker allowing room for the water pan. As

you gain experience in smoking, increase or decrease the

amount of wood to suit your taste. Fill water pan, place it in

the smoker and close the smoker lid.

Light the barbecue and preheat with all burners on HIGH,

lid down, for 10 minutes or until the thermometer registers

500°F - 550°F. Adjust the burners for cooking; MOM or

LOL will be your best settings for long duration smoking.

Smoke will start in approximately 10 minutes and last as

long as 45 minutes. If you require more smoke flavor, refill

the smoker with FireSpice Chips and/or Chunks and refill

the water pan with water. The Steam-N-Chips Smoker may

be used to enhance any of the meat, poultry and fish

recipes in the gas barbecue cookbook. Cook with the lid

down according to the times indicated in charts or recipes.

Note - After refilling smoker, smoke will take about 10 to

15 minutes to start again.

Cutaway view

Cleaning the Steam-N-Chips Smoker

Before each use, empty the Steam-N-Chips Smoker of

ash to allow proper air flow. Accomplish this by lightly

tapping the sides of the smoker and stirring the ashes so

that they sift through the bottom and fall into the bottom

tray of your barbecue. Remove bottom tray and empty.

Note - Smoking will leave a "smoke" residue on the

surface of the smoker.This residue cannot be removed

and will not affect the function of the Steam-N-Chips

Smoker.To a lesser degree a "smoke" residue will

accumulate on the inside of your Weber Gas Barbecue.

This residue need not be removed and will not adversely

affect the function of your Weber Gas Barbecue.

DANGER

Do not use any flammable fluid in the

Steam-N-Chips Smoker to ignite the wood.

This will cause serious bodily injury.

Place wood in here

Steam-N-Chips Flue

Figure 4

Water Pan

Steam-N-Chips Body

USING THE STEAM-N-CHIPS SMOKER

MAINTENANCE

Spider Stopper Guards

Your Gas Barbecue, as well as any outdoor gas appliance,

is a target for spiders and other insects. They can nest in

the venturi section of the burner tubes. This blocks the

normal gas flow, and can cause the gas to flow back out of

the air shutter. Figure 5. This could result in a fire in and

around the air shutters, under the control panel, causing

serious damage to your barbecue.

The Spider Stopper Guard is factory installed. It fits tightly

around the air shutter section of the burner tube and the

valve, thereby preventing spiders and other insects access

to the burner tubes through the air shutter openings. Figure

We recommend that you inspect the Spider Stopper

Guards at least once a year. Also inspect and clean the

Spider Stopper Guards if any of the following

symptoms should ever occur.

1. The smell of gas in conjunction with the burner flames

appearing yellow and lazy.

2. Barbecue does not reach temperature.

3. Barbecue heats unevenly.

4. One or more of the burners do not ignite.

Figure 5

Venturi

Air shutter

Venturi fin

Spider Stopper

Guard

Figure 6

DANGER

Failure to correct these symptoms may

result in a fire which can cause serious bodily

injury or death and cause damage to property.

Inspection and Cleaning of the Spider

Stopper Guards

To inspect the Spider Stopper Guards, remove the control

panel and look to see if they have dust or dirt on their

outside surfaces. If they are dirty, brush off the outside

surface of the Spider Stopper Guards with a soft bristle

brush (an old toothbrush for example). Check that there

are no gaps in the Spider Stopper Guards’ seams or in

the fit around the burners or valves.

MAINTENANCE

View from behind

cooking box

Wing nuts

Figure 11

Guide screw

Figure 12

Figure 10

Replacing Main Burners

a) Your Weber Gas Barbecue must be OFF and cool.

b) Turn gas OFF at source.

c) To remove the control panel, see the Step-By-Step Guide.

d) Unlatch the Spider Stopper Guards and remove.

Figure 10.

e) If your barbecue has a side burner, disconnect the side

burner hose.

f) Remove the manifold bracket and unscrew the two wing

nuts that hold the manifold to the cooking box. Pull the

manifold and valve assembly out of the burners and

carefully set it down. Figure 11.

g) Slide the burner assembly out from under the guide screw

and washer in the corners of the cooking box. Figure 12.

Main Burner Flame Pattern

The Weber Gas Barbecue burners have been factory set

for the correct air and gas mixture. The correct flame

pattern is shown in Figure 7.

If the flames do not appear to be uniform the length of the

burner tube, follow the burner cleaning procedures.

Main Burner Cleaning Procedure

Turn off the gas supply. Remove the manifold.

Look inside each burner with a flashlight. Figure 8.

Clean the inside of the burners with a wire (a straightened

out coat hanger will work). Figure 9. Check and clean the

air shutter opening at the ends of the burners. Check and

clean the valve orifices at the base of the valves. Use a

brass bristle brush to clean outside of burners. This is to

make sure all the burner ports are fully open.

CAUTION: Do not enlarge the burner ports when

cleaning.

Burner inside

cooking box

Figure 7

Dark blue

Light blue

Tips occasionally yellowish

Figure 8

Figure 9

Figure 16

White wire

Black wire

Crossover Ignition System Operations

If the Crossover Ignition System fails to ignite the Front

burner, light the Front burner with a match. If the Front

burner lights with a match, then check the Crossover

Ignition System.

■ Check that both the white and black ignition wires are

attached properly. Figure 16.

■ Check that the Crossover Ignition button pushes the

igniter (button) down, and returns to the up position.

■ Check to see if the igniter is loose in the frame. Tighten if

necessary; See “Check That Items Are Secured” in the

Step-By-Step Guide for correct procedure.

If the Crossover Ignition System still fails to light, contact

Weber-Stephen Customer Service.

MAINTENANCE

Crossover tube

Figure 13

CAUTION: If the Spider Stopper Guards do not fit

tightly, contact Weber-Stephen Customer Service.

CAUTION: After reinstalling the gas lines, they

should be leak checked with a soap and water

solution before using the barbecue.

Venturi fin

Figure 15

Check fit

around valve

Check fit around burner

h) Lift and twist the burner assembly slightly, to separate the

crossover tube from the burners. Figure 13. Remove the

burners from the cooking box.

i) To reinstall the burners, reverse steps c) through h).

CAUTION: The burner openings must be positioned

properly over the valve orifices. Figure 14 (a).

Check proper assembly before fastening manifold in

place. Figure 14 (b).

j) Reinstall the Spider Stopper Guards. Slightly rotate the

Spider Stopper Guards so that the seams are in line with

the Venturi fins. There should be no gaps in the seams or

in the fit around the burners and valves. Figure 15.

Figure 14

(a)

(b)

Valve

Burner

TROUBLESHOOTING

Problem

Burners burn with a yellow or orange

flame, in conjunction with the smell of gas.

Burner does not light, or flame is low in

HIGH position.

Experiencing flare-ups:

CAUTION: Do not line the bottom tray

with aluminum foil.

Burner flame pattern is erratic. Flame is low

when burner is on HIGH. Flames do not run

the whole length of the burner tube.

Inside of lid appears to be “peeling.”

(Resembles paint peeling.)

Check

Inspect Spider Stopper Guards for

possible obstructions. (Blockage of

holes.)

Is fuel hose bent or kinked?

Does the Front burner light with a

match?

Are you preheating barbecue in the

prescribed manner?

Are the cooking grates and

Flavorizer Bars heavily coated with

burned-on grease?

Is the bottom tray "dirty" and not

allowing grease to flow into catch pan?

Are burners clean?

The lid is porcelain-on-steel, not

paint. It cannot “peel.” What you are

seeing is baked on grease that has

turned to carbon and is flaking off.

THIS IS NOT A DEFECT.

Cure

Clean Spider Stopper Guards.

(See Maintenance Section.)

Straighten fuel hose.

If you can light the Front burner

with a match, then check the

Crossover Ignition System.

All burners on high for 10 to 15

minutes for preheating.

Clean thoroughly. (See Cleaning

Section.)

Clean bottom tray.

Clean burners. (See Maintenance

Section.)

Clean thoroughly. (See Cleaning

Section.)

If problems cannot be corrected by using these methods, please contact Weber-Stephen Customer Service.

Problem

Side burner does not light.

Flame is low in HIGH position.

Flame is very yellow in conjunction with

the smell of gas,

Burner makes popping noise in conjunction

with the smell of gas.

Push button ignition does not work.

Flame is large or erratic.

Check

Is gas supply off?

Is fuel hose bent or kinked?

Inspect burner ring slots for

obstructions.

Inspect burner base for

obstructions.

Does burner light with a match?

Is the burner ring correctly

installed?

Cure

Turn supply on.

Straighten hose.

Clean if necessary.

If match lights burner, check

igniter (see Side Burner

Maintenance).

See Side Burner Maintenance

for correct assembly.

SIDE BURNER TROUBLESHOOTING

For the Platinum Series II 3200 & 3400

WARNING: Before attempting any troubleshooting

steps, all gas controls and supply valves should be in

the OFF position.

WARNING: All gas controls and supply valves

should be in the OFF position. Figure 17 (a).

Make sure black wire is connected between igniter and

electrode. Make sure white wire is connected between

igniter and ground. Check that igniter lock nut is tight.

Figure 17 (b) and figure 17 (c).

Note - If the igniter works loose, carefully tighten the

igniter lock nut with an adjustable wrench or pliers.

SIDE BURNER MAINTENANCE

(a)

(c)

(b)

Figure 17

Ground

Electrode

Views from

figures 17 (b) and (c)

from under side burner

Figure 18

The Platinum Series II side burner has been factory set

for the correct air and gas mixture. The correct flame

pattern is shown in Figure 18.

Igniter lock nut

Black wire

White wire

Tips occasionally yellowish

Light

blue

Dark

blue

Figure 19

To Clean the Burner Head

Remove the windshield and grate. Remove the burner

cap. Figure 19 (a). Clean with soap and water. Soak if

necessary.

Remove the burner ring. Figure 19 (b). Clean with soap

and water. Soak if necessary.

CAUTION: Do not enlarge the slots in the burner

ring. Only clean with a cloth and soap and water.

Remove the burner head. Figure 19 (c). Clean with soap

and water. Soak if necessary.

Wipe out the burner base with a damp cloth and soap

and water.

CAUTION: Avoid getting water or dust in the burner

orifice.

Clean the ignition electrode with a damp cloth and soap

and water.

(a)

(c)

(b)

Burner cap

Burner ring

Burner head

Burner base

SIDE BURNER MAINTENANCE

Windshield

Grate

To Reassemble the Burner Head

Insert the burner head into the burner base. Figure 19 (c).

There is a hole in the burner head for the igniter electrode.

Set the burner ring onto the burner head. Rotate the

burner ring until the four lugs on the burner ring are

seated in the four slots on the burner head. Figure 19 (b).

WARNING: If the flame pattern is uneven or erratic,

turn OFF the burner control knob. Check the position

of the burner ring to the burner head. The lugs of the

burner ring must be in the slots of the burner head.

Install the burner cap. Figure 19 (a). Install the grate and

the windshield.

SIDE BURNER

EXPLODED VIEW

Windshield

Grate

Burner cap

Burner ring

Burner head

Burner base

Burner orifice

Igniter electrode

Burner orifice

Lug

Slot

Burner assembly consists of: burner cap, burner ring,

burner head, burner base, and burner orifice.

Note: The burner head has a hole in it that fits over the

igniter electrode.

PLATINUM SERIES II 2200 NATURAL GAS

EXPLODED VIEW

41-44

PLATINUM SERIES II 2200 NATURAL GAS

REPLACEMENT PARTS LIST

1 Hinge pin cotter (2)

2 Hinge pin (2)

3 Lid (assembly)

4 Thermometer

5 Weber warm-up basket

6 Warming rack

7 Steam-N-Chips Smoker

8 Steam-N-Chips Smoker flue

9 Cooking grate (2)

10 Cooking box

11 Keps nut

12 1/4-20 x 1/2 inch bolt (12)

13 Nylon washer (16)

14 Left work surface

15 Plastic plug (2)

16 Tool holder (3)

17 Front panel

18 Rear frame

19 1/4-20 x 1 1/2 inch bolt

20 Crossover rail

21 Front frame

22 Crossover rail

23 Caster (2)

24 Bottom wire rack

25 Bottom tray

26 Catch pan holder

27 Catch pan

28 Drip pan (2)

29 Short Flavorizer bar (7)

30 Long Flavorizer bar (5)

31 Burner control knob (3)

32 Control panel

33 Phillips screw (2)

34 Igniter button

35 Crossover tube

36 Front or back burner

37 Middle burner

38 Spider stopper guard (3)

39 Manifold bracket

40 Manifold assembly

41 Igniter

42 Igniter lock nut

43 Igniter wire (white)

44 Igniter wire (black)

45 Igniter bracket

46 Plastic bracket (2)

47 Right work surface

48 Wheel hub cap (2)

49 Wheel (2)

50 Crossover rail

51 Hose

All items are single quantities unless otherwise specified.

Parts can be ordered directly from Weber-Stephen

Products Company by phone or mail.

Note - Do not return parts to Weber-Stephen Products Co.

without first contacting the Customer Service Center by

phone or mail. Returning the part may not be necessary.

While we give much attention to our products,

unfortunately an occasional error may occur. If a part is

missing, do not go back to the store. Call the Weber

Customer Service Center toll free 1-800-446-1071 to

receive immediate assistance. Have your owner’s manual

and serial number of the barbecue available for reference.

Weber-Stephen Products Company

Customer Service Center

250 South Hicks Road

Palatine, IL 60067-6241

(800) 446-1071

WARNING:

Use only Weber factory authorized parts.The

use of any part that is not factory authorized can

be dangerous.This will also void your warranty.

PLATINUM SERIES II 3200 NATURAL GAS

EXPLODED VIEW

41-44

Page is loading ...

Weber PLATINUM SERIES 2 3400 NG User manual

Brand: Weber

Model: PLATINUM SERIES 2 3400 NG

Category: Barbecues & grills

Type: User manual

This manual is also suitable for

Download PDF

report

Weber PLATINUM SERIES 2 3400 NG User manual

This manual is also suitable for

Weber PLATINUM SERIES 2 3400 NG User manual

Related papers

Other documents