Thermador VCI21CS/01 Installation guide

Thewma_ow + Ao A=.=,c=.3co.-

Table of Contents

Safety .......................................................... 1

Installation ...................................................... 2

Before You Begin .................................................................... 2

Installation Procedure ................................................................. 5

Service ......................................................... 6

Before Calling Service ................................................................. 6

Questions?

1-800-735-4328

www.thermador.com

5551 McFadden Ave.

Huntington Beach, CA 92649

We look forward to hearing from you!

Safety

IMPORTANT SAFETY INSTRUCTIONS

__ READ AND SAVE THESE INSTRUCTIONS

Important Safety

Instructions

Appliance Handling Safety

Safety Codes and Standards

Electric Safety

WARNING: If the information in this manual is not followed exactly, fire or

shock may result causing property damage or personal injury.

WARNING: Do not repair or replace any part of the appliance unless specifi-

cally recommended in the manuals. Improper installation, service or mainte-

nance can cause injury or property damage. Refer to this manual for

guidance. All other servicing should be done by a qualified technician.

• Unit is heavy and requires at least two people or proper equipment to move.

• Hidden surfaces may have sharp edges. Use caution when reaching behind

or under appliance.

This appliance complies with one or more of the following Standards:

1) UL 858, The Standard for the Safety of Household Electric Ranges

2) UL 923, The Standard for the Safety of Microwave Cooking Appliances

3) UL 507, The Standard for the Safety of Electric Fans

4) ANSI Z21.1-2000, The American National Standard for Household Cook-

ing Gas Appliances

5) CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators

6) CAN/CSA-C22.2 No. 61-M89 Household Cooking Ranges

It is the responsibility of the owner and the installer to determine if additional

requirements and/or standards apply to specific installations.

• GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit,

grounding reduces the risk of electric shock by providing an escape wire for

the electric current. This appliance is equipped with a cord having a grounding

wire with a grounding plug. The plug must be plugged into an outlet that is

properly installed and grounded.

• WARNING: Improper grounding can result in a risk of electric shock.

• Consult a qualified electrician if the grounding instructions are not completely

understood, or if doubt exists as to whether the appliance is properly

grounded.

• Do not use an extension cord. If the power supply cord is too short, have a

qualified electrician install an outlet near the appliance.

• For appliances equipped with a cord and plug, do not cut or remove the

ground prong. It must be plugged into a matching grounding type receptacle

to avoid electrical shock. If there is any doubt as to whether the wall recepta-

cle is properly grounded, the customer should have it checked by a qualified

electrician.

• If required by the National Electrical Code (or Canadian Electrical Code), this

appliance must be installed on a separate branch circuit.

• WARNING: To reduce the risk of fire or electric shock, do not use this fan with

any solid-state speed control device.

• Installer - show the owner the location of the circuit breaker or fuse. Mark itfor

easy reference.

English 1

,_ Safety

Ventilation Safety

Related Equipment Safety

• Before installing, turn power OFF at the service panel. Lock service panel to

prevent power from being turned ON accidentally.

• WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer.

b) Before servicing or cleaning unit, switch power off at service panel and

lock the service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device, such as a tag, to

the service panel.

• Be sure your appliance is properly installed and grounded by a qualified tech-

nician. Installation, electrical connections and grounding must comply with all

applicable codes.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualified person(s)

in accordance with all applicable codes and standards, including fire-

rated construction.

b) Sufficient air is needed for proper combustion and exhausting of gases

through the flue (chimney) of fuel burning equipment to prevent back

drafting. Follow the heating equipment manufacturer's guideline and

safety standards such as those published by the National Fire Protection

Association (NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and the local code authori-

ties.

c) When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

d) Ducted fans must always be vented to the outdoors.

• Remove all tape and packaging before using the appliance. Destroy the pack-

aging after unpacking the appliance. Never allow children to play with packag-

ing material.

• Never modify or alter the construction of the appliance. For example, do not

remove leveling legs, panels, wire covers or anti-tip brackets/screws.

• CAUTION: For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

• WARNING: To reduce the risk of fire, use only metal ductwork.

Installation

Before You Begin

Tools and Parts

Needed

Parts Included

1. Custom Ventilation Hood and Chimney Assembly

2. Ductwork as necessary (style varies)

3. Duct Tape

4. Phillips Head Screwdriver

1. Filters(2)

2. Halogen bulbs (2, installed)

3. Screws, Flat Phillips 3.5 x 15 cm (4)

Note: You may use Flat Phillips 6 x 5/8 in. screws as a substitute.

English 2

Installation

4. OneWayDamper

Ifpartsaremissingordamaged,callthenumberorwritetotheaddresslisted

insidethefrontcover.

General Information

Overall Dimensions

The ventilation unit is designed for installation inside a custom-built hood and

chimney assembly. It is for ducting to the outside; It cannot be used in conjunction

with a recirculation unit.

Installation height above cooktop is the user's preference. The lower the hood

above the cooktop, the more efficient the capturing of cooking odors, grease, and

smoke. This hood has been approved for installations as low as 30" (760 mm) and

as high as 36" (900 mm) above the cooktop. The lower height may be inconve-

nient for tall people and large cooking vessels.

93/4" 93/4"

:_ (248mm) _ (248mm) ..........

: (_ 6" (150mm)

T

15'

(38imm)

Figure 5: Overall Dimensions - 20 7/8" (53 cm) models

133/4" 133/4"

(348ram) _ (348mm) ..........

' (_ 6" (150ram)

............. i

' 1 3/8"(35_n 2 1/8"(55 mm)

135/8"

mm)

Figure6: Overall Dimensions - 28 3/4" (73 cm) models

English 3

Installation

Preparation

Electrical Requirements

Mounting Requirements

The unit requires a 120V AC, 60Hz. 15A branch circuit. For future service, install

the outlet in an easily accessible location.

The unit must be mounted to the surrounding housing. See "General Information"

on page 3 for suggestions for determining hood height.

For best results, install the unit as far up in the housing or hood as possible. This

will improve the function of the appliance.

When calculating the load for the housing support system, be sure to include the

weight of the ventilation unit. See "Ventilation Unit Weight" on page 4. for unit

weight by model.

Table 1: Ventilation Unit Weight

21" (53 cm) 18 1/4 lbs. (8.3 kg)

29" (73 cm) 19 Ibs. (8.7 kg)

For proper performance, the housing must cover the entire cooking surface.

Build housing to correspond with Figure 7: Housing Cutout Dimensions - 20 718"

(53 cm) models or Figure 8: Housing Cutout Dimensions - 28 314"(73 cm) mod-

els.

Figure 7: Housing Cutout Dimensions - 20 7/8" (53 cm) models

English 4

Installation

Figure8:HousingCutoutDimensions-283/4"(73cm)models

Ducting Recommendations The unit is for ducting to the outside; it cannot be used in conjunction with a recir-

culation unit.

For the most efficient air flow exhaust, use a straight duct run or as few elbows as

possible.

Do not use flex ducting. Always use metal ductwork with a diameter of 6" (150

mm).

COLD WEATHER installations should have an additional backdraft damper

installed to minimize backward cold air flow and a nonmetallic thermal break to

minimize conduction of outside temperatures as part of the ductwork. The damper

should be on the cold air side of the thermal break. The break should be as close

as possible to where the ducting enters the heated portion of the house.

Always install a metal vent cover where the ductwork exits the house.

Make-Up Air: Local building codes may require the use of make-up air systems

when using ducted ventilation systems greater than specified CFM of air move-

ment. The specified CFM varies from locale to locale. Consult your HVAC profes-

sional for specific requirements in your area.

Installation Procedure

Unpack Hood

Prepare ductwork

,_ WARNING: To avoid electrical shock hazard, before installing,

switch power off at the service panel and lock the panel to prevent the

-- power from being switched on accidentally.

Pull hood from outer packaging. Remove and discard all packaging materials.

Remove filter and set aside (See Use and Care manual for removal instructions).

Install one-way damper so that the flap opens up (snaps into place). Note: verify

that the flap opens up (toward the ceiling) before continuing. If necessary, install

thermal break and additional backdraft damper.

English 5

Service

Install Housing

Connect to Ductwork

See "General Information" on page 3 for recommended installation height and

"Mounting Requirements" on page 4 for information on mounting specifications.

Install housing as directed by the manufacturer.

Connect ventilation unit to ductwork in house.

Connect Electric

Install the Unit

Plug electrical cord into grounded outlet. Before you plug in an electrical cord, be

sure all controls are in the OFF position.

Press unit up into housing until plastic clips on front and rear snap into the hous-

ing. Install 4 screws through tapholes into housing.

Figure 9: Install the Unit

Final Steps

Install Filters. See Use and Care manual for detailed instructions.

Test The Installation

Test the operation of the blower and the lights.

Note: Be sure to check for backdraft. With the blower on high, close the windows

and doors to the area to ensure that fan does not cause back drafting in any outlet

vent for another appliance.

Service

Before Calling

Service

Product Data Plate

See Use and Care Manual for troubleshooting information. Refer to the Warranty

in the Use and Care Manual. Please be prepared with the information printed on

your product data plate when calling.

The data plate shows the model and serial number. It is located under the filter.

English 6

Service

Keepyourinvoiceorescrowpapersforwarrantyvalidationifserviceisneeded.

DataPlate

behindfilter

Figure 10: Data Plate Location

English 7

Table des mati_res

Securit6 ........................................................ 1

Installation ...................................................... 3

Avant de commencer .................................................................. 3

Methode d'installation ................................................................. 6

Service ......................................................... 7

Avant d'appeler le service apres-vente .................................................... 7

Questions ?

1-800-735-4328

www.thermador.com

5551 McFadden Ave.

Huntington Beach, CA 92649

Nous attendons de vos nouvelles !

Page is loading ...

f

Indice

Seguridad ....................................................... 1

Instalaci6n ...................................................... 3

Antes de empezar ................................................................... 3

Procedimiento de instalaci6n ........................................................... 6

Servicio tecnico .................................................. 7

Antes de llamar al servicio tecnico ...................................................... 7

/.,Preg untas ?

1-800-735-4328

www.thermador.com

5551 McFadden Ave.

Huntington Beach, CA 92649

iEsperamos tener noticias suyas pronto!

Page is loading ...

Ther_edor A° Am=,vic..3co=-

5551 McFadden Avenue, Huntington Beach CA, 92649 * 800-735-4328 * www.thermador.com

Thermador VCI21CS/01 Installation guide

This manual is also suitable for

Thermador VCI21CS/01 Installation guide

in other languages

Related papers

Other documents