Poulan PRO
Instruction Manual
Manual de Instrucciones
Manuel d'lnstructions
PP136
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENOIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Lire le manuel d'instructions et bien respecter tousles avertisse-
ments et toutes les instructions de s6curite. Tout defaut de le
faire pourrait entraTner des blessures graves.
Poulan PRO
1030 Stevens Creek Road
Augusta, GA30907
545123424 8/10/06
Only the following Gasoline Powered Combination Gardening Appliance powerhead models
and their respective attachments have been Classified by Underwriters Laboratories. Inc.. in
accordance with the applicable safety requirements.
Powerhead including trimmer attachment ........................... PP136
Optional blower attachment ......................................... PP3000B
Optional brushcutter attachment ................................... PP4000C
The following attachment is Listed by Underwriter's Laboratories, Inc., in accordance with
U L Standard 1602, "Gasoline- Engine- Powered, Rigid- Cutting Member, Edgers and Edge-
Trimmers."
Optional edger attachment ......................................... PP1000E
zt,
WARNING: When using gardening
appliances, basic safety precautions must eF
ways be followed to reduce the risk of fire and
serious injury. Read and follow all instruc-
tions.
This power unit cat? be dangerous! Operator is
responsible for following instructions and warn-
ings on unit and in manual. Read entire instruc-
tion manual before using unit! Be thoroughly fa-
miliar with the controls and the proper use of the
unit. Restrict the use of this unit to persons who
have read, understand, and will follow the
instructions and warnings on the unit and in the
manual. Never allow children to operate this
unit.
INSTRUCTION SAFETY INFORMATION
MANUAL ON THE UNIT
_ DANGER: Never use blades with line
trimmer attachment. Never use flailing de-
vices with any attachment. This unit (when
used with supplied line trimmer attachment) is
designed for line trimmer use only. Use of any
other accessories with line trimmer attach-
ment will increase the risk of injury.
O-©O
A
il_ WARNING: Trimmer line throws ob-
jects violently. You and others can be blinded/in-
jured, Wear eye and leg protection, Keep body
parts clear of rotating line.
Eye Protection
_t____/ HezardZone
_/Boots
Keep children, bystanders, and animals 50 feet
(15 meters) away. Stop unit immediately if ap-
proached.
If situations occur which are not covered in
this manual, use care and good judgment. If
you need assistance, contact your authorized
service dealer or call t-800-554-6723.
OPERATOR SAFETY
• Dress proper_y. A_ways wear safety
glasses or similar eye protection when op-
erating, or performing maintenance, on
your unit (safety glasses are available).
Eye protection should be marked Z87.
• Always wear face or dust mask ifoperation
is dusty.
• Always wear heavy, long pants, long
sleeves, boots, and gloves. Wearing safety
leg guards is recommended.
• Always wear foot protection. Do not go
barefoot or wear sandals. Stay clear of
spinning line.
• Secure hair above shoulder length. Secure
or remove loose clothing or clothing with
loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.
• Being fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line.
• Stay Alert. Do not operate this unit when
you are tired, ill, upset or under the influ-
ence of alcohol, drugs, or medication.
Watch what you are doing; use common
sense.
• Wear hearing protection.
• Never start or run inside a closed room or
building. Breathing exhaust fumes can kill.
• Keep handles free of oil and fuel.
• Always keep engine on the right hand side
of your body.
•Hoid the unit firmly with both hands.
• Keep trimmer head (or other optional at-
tachment) below waist level and away from
all parts of your body. Do not raise engine
above your waist.
• Keep all parts of your body away from muf-
fler and spinning line (or other optional at-
tachment). Keep engine below waist level.
A hot muffler can cause serious burns.
• Keepfirmfootingand balance. Do notover-
reach or use from unstable surfaces such
as ladders, trees, steep slopes, rooftops,
etc.
• Use only in daylight or good artificial light.
• Use only for jobs explained in this manual
(or manuals for optional attachments).
2
UNIT / MAINTENANCE SAFETY
• Disconnect the spark plug before perform-
ing maintenance except carburetor adjust-
ments.
• Look for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keep in good working
condition.
• Replace trimmer head parts that are
chipped, cracked, broken, or damaged in
any other way before using the unit.
• Maintain unit according to recommended
procedures. Keep cutting line at proper
length.
• Use only 0.080" (2 mm) diameter Poulan
PRO brand line. Never use wire, rope, string,
etc.
• Install required shield properly before using
the unit. Use only specified trimmer head;
make sure it is properly installed and se-
curely fastened.
• Make sure unit is assembled correctly as
showe in this manual.
• Make carburetor adjustments with lower
end supported to prevent line from contact-
ing any object.
• Keep others away when making carburetor
adjustments.
• Use only recommended Poulan PRO ac-
cessories and replacement parts.
• Have all maintenance and service not ex-
plained in this manual performed by an au-
thorized service dealer.
FUEL SAFETY
• Mix and pour fuel outdoors.
• Keep away from sparks or flames.
• Use a container approved for fuel.
• Do not smoke or allow smoking near fuel or
the unit.
• Avoid spilling fuel or oil. Wipe up all fuel
spills.
• Move at least 10 feet (3 meters) away from
fueling site before starting engine.
• Stop engine and allow to cool before re-
moving fuel cap.
• Always store gasoline in a container ap-
proved for flammable liquids.
TRANSPORTING AND STORAGE
• Allow engh_e to cool before storing or trans-
porting in vehicle.
• Emptythe fueItank before storing or trans-
porting the unit. Use up fuel left in the carbu-
retor by starting the engine and letting it run
until it stops.
• Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
• Store unit so line limiter blade cannot acci-
dentally cause injury. The unit can be hung
by the shaft.
• Store unit out of reach of children.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause btood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti-vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. Ifyou
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by an autho-
rized service dealer.
LINE TRIMMER SAFETY
_WARNING: Inspect the area to be
trimmed before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by or become entangled in line.
Hard objects can damage the trimmer head
and be thrown causing serious injury.
• Use only for trimming, scalping, mowing and
sweeping. Do not use for edging, pruning or
hedge trimming.
• Cut from your left to your right. Cutting on
right side of the shield will throw debris
away from the operator.
ADDITIONAL SAFETY RULES
FOR OPTIONAL ATTACHMENTS
m_WARNING: For each optional at-
tachment used, read entire instruction manu-
al before use and follow all warnings and in-
structions in manual and on attachment.
_L, WARNING: Ensure handlebar is
installed when using edger or brushcutter at-
tachments. Attach handlebar above arrow on
safety label on the upper shaft (engine end of
unit). If your edger or brushcutter attachment
does not include a handlebar, a handlebar ac-
cessory kit (#530071451) is available from
your authorized service dealer.
EDGER SAFETY
WARNING: Inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
• Blade rotates momentarily after the trigger
is released. The blade can seriously cut
you or others.
• Allow blade to stop before removing it from
the cut.
Bladerotates
after the
Allowbladeto stop
beforeremovingit
fromthe cut.
• Throw away blades that are bent, warped,
cracked, broken or damaged in any other
way. Replace parts that are cracked,
chipped, or damaged before ush_g the unit.
• Do not attempt to remove cut material nor
hotd material to be cut when the engine is
running or when cutting blade is moving.
• Always keep the wheel and depth adjusting
skid in contact with the ground.
• Always push the unit slowly over the
ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.
• Always use the handlebar when using edg-
er attachment.
BLOWER/VACUUM SAFETY
_WARNING: Inspect area before
starting unit. Remove all debris and hard ob-
jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
• Do not set unit on any surface except a
clean, hard area while engine is running.
Debris such as gravel, sand, dust, grass,
etc., could be picked up by the air intake
and thrown out through discharge opening,
damaging unit, property, or causing serious
injury to bystanders or operator.
• Never place objects inside the blower
tubes, vacuum tubes or blower outlet. Al-
ways direct the blowing debris away from
people, animals, glass, and solid objects
such as trees, automobiles, wails, etc. The
force of air can cause rocks, dirt, or sticks to
be thrown or to ricochet which can hurt
people or animals, break glass, or cause
other damage.
• Never run unit without the proper equip-
ment attached. When using your unit as a
blower, always install blower tubes.
• Check air intake opening, blower tubes or
vacuum tubes frequently, always with en-
gine stopped and spark plug disconnected.
Keep vents and discharge tubes free of de-
bris which can accumulate and restrict
proper air ftow.
• Never place any object in air intake opening
as this could restrict proper air flow and
cause damage to the unit.
• Never use for spreading chemicals, fertiliz-
ers, or other substances which may contain
toxic materials.
• To avoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
BRUSHCUTTER SAFETY
,,_ DANGER: Blade can thrust violently
away from material it does not cut. Blade
thrust can cause amputation of arms or legs.
,_k WARNING: Do not use trimmer head
as a fastening device for the blade.
IlWAHNINL_: The blade continues to
spin after the throttle is released or engine is
turned off. The coasting blade can throw ob-
jects or seriously cut you if accidentally
touched. Stop the blade by contacting the
right hand side of the coasting blade with ma-
terial already cut.
Stop coasting
blade by contact
with cut material.
®
m_WARNING: Inspect the area to be
cut before each use. Remove objects (rocks,
broken glass, nails, wire, etc.) which can be
thrown or become entangled in the blade or
trimmer line.
• Throw away and replace blades that are
bent, warped, cracked, broken or damaged
in any other way.
• Install required shield properly before using
the unit. Use the metal shieId for all metal
blade use.
4
A
411WARNING: Only use brushcutter at-
tachments that provide a metal shield with
proboscis nose.
FrOo OSO,S
• Use only specified blade and make sure it is
properly instailed and securely fastened.
• Cut from your left to your right. Cutting on
the right side of the shield will throw debris
away from the operator.
• Always use the handlebar and a properly
adjusted shoulder strap with blade (see AS-
SEMBLY instructions in brushcutter attach-
ment instruction manual).
CULTIVATOR SAFETY
WARNING: Rotating tines san cause
serious injury. Keep away from rotating tines.
Stop the engine and disconnect the spark
plug before unclogging tines or making re-
pairs.
A
411WARNING: Inspect the area to be
cultivated before starting the unit. Removeall
debris and hard and sharp objects such as
rocks, vines, branches, rope. string, etc.
• Avoid heavy contact with solid objects that
might stop the tines. If heavy contact oc-
curs, stop the engine and inspect the unit
for damage.
• Never operate the cultivator without the tine
cover in place and properly secured.
• Keep the tines and guard clear of debris.
• After striking a foreign object, stop the en-
gine. disconnect the spark plug and inspect
the cultivator for damage. Repair before re-
starting.
• Disconnect attachment from the drive en-
gh_e before cleaning the tines with a hose
and water to remove any build-up. Oil the
th_es to prevent rust.
• Always wear gloves when servicing or
cleaning the tines. The tines become very
sharp from use.
• Do not run unit at high speed unless culti-
vating.
HEDGE TRIMMER SAFETY
_DANGER: RiSK OF CUT; KEEP
HANDS AWAY FROM BLADE - Blade
moves momentarily after the trigger is re-
leased. Do not attempt to clear away cut ma-
teriai when the blade is in motion. Make sure
the switch is in the OFF position, the spark
plug wire is disconnected, and the blade has
stopped moving before removing jammed
material from the cutting blade. Do not grab or
hold the unit by the cutting blade.
Blades move
momentarily
after the
dtrigger is
Allow blades to stop
before removing
them from the cut.
_, WARNING: Inspectthe areabefore
starting the unit. Remove aHdebris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
• Do not use a cutting blade that is bent.
warped, cracked, broken or damaged in
any other way. Have worn or damaged
parts replaced by your authorized service
dealer.
• Always keep unit in front of your body.
Keep atl parts of your body away from the
cutting blade.
• Keep the cutting blade and air vents clear of
debris.
POLE PRUNER SAFETY
_WARNING: The reciprocating blade/
rotating chain can cause severe injury. In-
spect the unit before use. Do not operate unit
with a bent. cracked or dull blade or dull chain.
Keep away from the blade/chain.
_, WARNING: The reciprocatingblade/
rotating chain is sharp. Do not touch. To pre-
vent serious injury, always stop engine and
ensure blade/chain has stopped moving, dis-
connect spark plug, and wear gloves when
changing or handling the blade or chain.
_L, WARNING: A coasting blade/rotat-
ing chain can cause injury while itcontinues to
move after the engine is stopped. Maintain
proper control of the unit untit the Made/chain
has completely stopped moving. Keep
hands, face and feet at a distance from all
moving parts. Do not attempt to touch or stop
the blade or chain when it is moving.
41_I,WARNING: Falling objects can
cause severe headinjury. Wear head protec-
tion when operating this unit with a pole prun-
er attachment,
5
.-&
WARNING: Topreventserious inju-
ry,do not use more than one boom extension
with a pole pruner attachment,
WARNING: Keep the pruner away
from power lines or electrical wires.
• Only use for pruning limbs or branches up
to 4 inches in diameter.
• Do not operate the unit faster than the
speed needed to prune. Do not run the unit
at high speed when not pruning.
• Always stop the unit when work is delayed
or when walking from one cutting location to
another.
• If you strike or become entangled with a for-
eign object, stop the engine immediately
and check for damage. Have any damage
repaired by an authorized service dealer
before attempting further operations. Dis-
card biades that are bent, warped, cracked
or broken.
• Stop the unit immediately if you feel exces-
sive vibration, Vibration is a sign oftrouble.
Inspect thoroughly for loose nuts, bolts or
damage before continuing. Contact an au-
thorized service dealer for repair or re-
placement of affected parts as necessary.
SNOW THROWER SAFETY
_WARNING: Keep hands and feet
away from the rotor when starting or running
the engine, Never attempt to clear the rotor
with the engine/motor running. Stop engine
and disconnect spark plug before unclogging
snow or debris from discharge chute or when
adjusting vanes.
m_WARNING: Never lean over dis-
charge chute. Rocks or debris could be
thrown into the eyes and face and cause seri-
ous injury or blindness.
'|!_,WARNING: inspect the area where
the unit is to be used. Remove objects that
could be thrown or damage the unit. Some
objects may be hidden by fallen snow - be
alert for the possibility.
• Direct material discharge away from glass
enclosures, automobiles, etc.
• Do not run engine at high speed while not
removh_g snow.
• Be attentive when using the snowthrower,
and stay alert for holes in the terrain and
other hidden hazards.
• Make sure the rotor will spin freely before
attaching the snowthrower to the power-
head.
• Ifthe rotor will not rotate freely duetofrozen
ice, thaw the unit before thoroughly before
attempting to operate under power.
• Keep the rotor clear of debris.
• Do not throw snow near other people. The
snow thrower could propel small objects at
high speed causing injury.
• After striking a foreign object, stop the en-
gine, disconnect spark pIug and inspect the
snowthrower for damage and repair if nec-
essary before restarting unit.
• Never operate the snowthrower near glass
enclosures, automobiles and trucks.
• Never attempt to use the snowthrower on a
roof.
• Never operate the snowthrower near win-
dow wells, dropoffs, etc.
• Never discharge snow onto public roads or
near moving traffic.
• Clear snow from slopes by going up and
down; never across. Use eautioe when
changing directions. Never clear snow from
steep slopes.
• Let snowthrower run for a few minutes after
clearing snow so moving parts do not
freeze.
• Look behind and use care when backing
up. Exercise caution to avoid slipping or fai-
ling, especially when operating in reverse.
• Know how to stop quickly.
d_I_WAI-(I_III_I_: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examh_e parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Fh_ding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
INSTALLING TRIMMER ATTACH-
MENT
CAUTION: When installh_g trimmer attach-
ment. place the unit on a flat surface for stabil-
ity.
1. Loosen the coupler by turning the knob
counterclockwise.
Coupler
Shipping
protector
Knob
TIGHTEN
2. Remove shipping protector from coupler.
3. Remove the shaft cap from the trimmer
attachment (if present).
4. Position locking/release button of attach-
ment into guide recess of coupler.
5. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
6. Before using the unit. tighten the knob se-
curely by turning clockwise.
couple r Primary Hole
Guide Recess
Upper Locking/ Attachment
Shaft Release
Button
mlWARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit. All attachments are designed
to be used in the primary hoIe unless otherwise
stated in the ap#icable attachment instruction
manual. Using the wrong hole could lead to seri-
ous injury or damage to the unit.
Secondary Hole
Locking/Release
Button in Primary Hole
For optional attachments, see the AS-
SEMBLY section of the applicable attach-
ment instruction manual.
ATTACHING SHIELD
'_L,WARNING: Theshieldmustbeprop-
erlyinstaIled. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you. For proper
orientation of shield, see KNOW YOUR TRIM-
MER illustration in OPERATION section.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole
in bracket.
4. Securely tighten wing nut onto bolt.
Slot Wing Nut
Bracket
Shield
PIVOT
ADJUSTING THE HANDLE
,_ WARNING: When adjusting the assist
handle, be sure itremains above the safety label
and below the mark or arrow on the shaft.
1. Loosen wing nut on handle.
2. Rotate the handle on the shaft to an up-
right position; retighten wing nut.
KNOW YOUR TRIMMER
READTHIS INSTRUCTION MANUALAND SAFETY RULESBEFORE OPERATINGYOUR UNIT
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Assist Handle
J
Coupler
Trimmer Shaft
Head _ ON/OFF Switch
Starter Handle
Shield
Primer Bulb
Line Umiter Throttle
Blade Trigger
Choke Lever Muffler
ON/OFF SWITCH
The ON/OFF switch is located on the trigger
handle and is used to stop the engine. Move the
switch to the OFF position to stop the engine.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fueI lines and filis them with fuel.
This allows you to start the engine with fewer
pulis on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
CHOKE
The CHOKE he_ps to supply fue_ to the engine
to aid in cold starting. Activate the choke by
moving the choke tever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
COUPLER
The COUPLER enables optional attach-
ments to be installed on the unit.
BEFORE STARTING ENGINE
,_ WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. if you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723,
FUELING ENGINE
_ WARNING: Remove fuel cap slowly
when refueling.
HELPFUL TIP I
Toobtain the correct oil mix I
J ratio, pour 3.2 ounces of I
2-cycle synthetic oil into I
one gallon of fresh gas. I
is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/WEED EATER brand
synthetic oil is recommended. Mix gasoline and
oil at a ratio of 40:1, A 40:1 ratio is obtained by
mixing 3.2 ounces (95 ml) of oil with 1 gallon (4
liters) of unleaded gasoline, DO NOT USE
This engine
automotive oil or marine oil. These oits will
cause engine damage. When mixing fuel. follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily
to assure that the fuel is thoroughly mixed.
Always read and follow the safety rules relating
to fuel before fueling your unit.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during stor-
age. Acidic gas can damage the fuel system
of an engine while in storage. To avoid engine
problems, empty the fuel system before stor-
age for 30 days or longer. Drain the gas tank.
start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur. See the STORAGE sec-
tion for additional information.
HOW TO STOP YOUR UNIT
• To stop the engine, move the ON/OFF
switch to the OFF position.
• If engine does not stop, move choke lever
to FULL CHOKE position.
8
ON/OFF Switch
HOW TO START YOUR UNIT
'_WARNING: Avoid any contact with
the muffler. A hot muffler can cause serious
burns.
HELPFUL TIP I
!f your engine still does not I
Pstart after foflowing these I
instructions, please Carl
1-800-554-5723.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
L._arting Posiflon
Primer Bulb
Choke
_Lever
Choke
position
decal
8. Pull starter rope sharply until engine runs,
but no more than 6 pulls. If the engine
doesn't start after 6 pulis (at the HALF
CHOKE position), move the choke lever to
the FULL CHOKE position and press the
primer bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the starter
rope until the engine runs, but no more than
6 pulis, if the engine doesn't start, repeat
procedure 2 additional times.
NOTE: If engine still doesn't start, it is
probably flooded. Proceed to STARTING A
FLOODED ENGINE.
9. Once the engine starts, allow it to run 10
seconds, then move the choke lever to
OFF CHOKE by aligning lever with posi-
tion shown on decal (see illustration be-
low). Allow the unit to run for 30 more se-
conds at OFF CHOKE before releasing
the throttle trigger. NOTE: if engine dies
with the choke lever in the OFF CHOKE
position, move the choke lever to the
HALF CHOKE position and pull the rope
until engine runs, but no more than 6
pulis.
1,
2.
3.
4.
Muffler
Set unit on a flat surface.
Move ON/OFF switch to the ON position.
Slowly press the primer bulb 6 times.
Move choke lever to FULL CHOKE by
aligning lever with position shown on de-
cal (see illustration below).
Choke
position
decal
5. Squeeze the throttle trigger fully and hold
through all remaining steps.
6. Pull starter rope handle sharply until en-
gine sounds as if it is trying to start, but do
not pull rope more than 6 times.
7. As soon as engine sounds as if it is trying
to start, move choke tever to HALF
CHOKE by aligning lever with position
shown on decal (see following illustra-
tion).
Choke
position
decat
STARTING A WARM ENGINE
1. Move ON/OFF switch to the ON position.
2. Move the choke lever to the HALF
CHOKE position.
3. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
4. Pullstarter rope sharply until engine runs,
but no more than 5 pulls.
5. Allow engine to run 15 seconds, then
movethe choke lever to the OFF CHOKE
position.
NOTE: if engine has not started, pull starter
rope 5 more pulls. If engine still does not run. it
is probably flooded.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handte many times depending on how badly
the unit is flooded.
9
If theunitstilldoesn'tstart,referto
TROUBLESHOOTINGTABLEor call
1-800-554-6723.
OPERATING THE COUPLER
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:
MODEL:
Edger ....................... PP1OOOE
Cultivator .................... PP2000T
Blower ...................... PP3000B
Brushcutter .................. PP4000C
Pruner ...................... PP5000P
WAR NIN G: Always stop unit and dis-
connect spark plug before removing or instaF
ling attachments.
REMOVING TRIMMER ATTACH-
MENT (OR OTHER OPTIONAL AT-
TACHMENTS)
CAUTION: When removh_g or installing at-
tachments, place the unit on a flat surface for
stability.
1. Loosen the coupler by turnh_g the knob
counterclockwise.
Upper Shaft
Coupler
Lower \
Attachment
TIGHTEN Knob
Press and hold the locking/release button.
Locking/Release
Button
Coupler Primary Hole
Guide Recess
Upper Locking/ Attachment
Shaft Release
Button
w_WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securety tightened before op-
erating the unit. All attachments are designed
to be used in the primary hole unless otherwise
stated in the applicable attachment instruction
manual Using the wrong hole could lead to seri-
ous injury or damage to the unit.
Secondary Hole
Locking/Release
Button in Primary Hole
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
OPERATING POSITION
ALWAYS WEAR:
Eye Protection
Lower Attachment
3. While securely holding the engine and
upper shaft, pull the attachment straight
out of the coupter.
INSTALLING OPTIONAL ATTACH-
MENTS
1. Remove the shaft cap from the attach-
ment (if present).
2. Position locking/release button of attach-
ment into guide recess of coupler.
3. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
4. Before using the unit. tighten the knob se-
curely by turning clockwise.
Long Pan%
Heavy SI
Cut from your left to your right. _'-'-
A
WARN ING: Alwaysweareye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficientIy
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise
and vibration. The cutting line will last longer
and will be less likely to "weld" onto the spool.
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
10
To stop engine:
• Release the throttle trigger,
• Move the ON/OFF switch to the OFF posi-
tion.
TRIMMER LINE ADVANCE
The trimmer line will advance approximately 2
inches (5 cm) each time the bottom of the
trimmer head is tapped on the ground with the
engine running at full throttle.
The most efficient line length is the maximum
length allowed by the line limiter.
Always keep the shield in place when the tool
is being operated,
To advance line:
• Operate the engine at full throttle,
• Hold the trimmer head paraltel to and above
the grassy area.
• Tap the bottom of the trimmer head lightly on
the ground one time, Approximately 2 inches
(5 cm) of line will be advanced with each tap.
Always tap the trimmer head on a grassy
area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head.
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob-
tain the most efficient tine length.
_i WARNING: use only 0.080" (2 mm)
diameter line. Other sizes of line will not ad-
vance properly and can cause serious injury.
Do not use other materials such as wire,
string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.
CUTTING METHODS
_IWARNING: Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage thetrimmer head, become
entangled in the line, or be thrown causing a
serious hazard,
• The tip of the line does the cutting, You will
achieve the best performance and
minimum line wear by not crowding the line
into the cutting area, The right and wrong
ways are shown below.
Tip of line does Line crowded into
• For trimming or scalping, use less than full
throttle to increase line Iife and decrease head
wear, especially:
• During light duty cutting.
• Near objects around which the line can
wrap such as small posts, trees or fence
wire,
• For mowing or sweeping, use full throttle for
a good clean job.
TRIMMING - Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact, Do not force trimmer line into
work area.
Trimming
3 inches (8 crr
above ground
SCALPING - The scalping technique re-
moves unwanted vegetation down to the
ground, Hotd the bottom of the trimmer head
about 3 inches (8 cm) above the ground and
at an angle. Allow the tip of the line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.
Scalping
MOWING - Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground, Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
Mowing
Right W_ong
• The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
11
SWEEPING - The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the Ih_e parallel to and above
the surfaces beh_g swept and move the tool
from side to side.
Sweeping
,&
m_WARNING: Disconnect the spark
plug before performing mah_tenance except
for carburetor adjustments.
HELPFUL TIP
IMPORTANT: Have all
repairs other than the rec-
ommended maintenance
described in the instruction
manual performed by an
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Poulan PRO may not pay for
repairs Under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
CHECK FOR LOOSE
FASTENERS AND PARTS
• Spark Plug Boot
• Air Filter
• Housing Screws
• Assist Handle Screw
• Debris Shield
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
• ON/OFF Switch - Ensure ON/OFF switch
functions properly by moving the switch to
the OFF position. Make sure engine stops;
then restart engine and continue.
• Fuel Tank - Discontinue use of unit if fuel
tank shows signs of damage or leaks.
• Debris Shield - Discontinue use of unit if
debris shield is damaged.
INSPECT AND CLEAN UNIT AND LA-
BELS
• After each use, inspect compIete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
• Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove parts by pressing button to re-
lease air filter cover.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Replace parts.
_>., Air Filter
Button _._7-p.. x. _,
_-:"_ _J _-_H-_ Cover
MUFFLER AND SPARK ARREST-
ING SCREEN
,_ WARNING: The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen.
For normal homeowner use, however, the
muffler and spark arresting screen will not re-
quire any service. After 50 hours of use, we
recommend that your muffler be serviced or
replaced by your authorized service dealer.
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch (0.6 mm). Igni-
tion timing is fixed and nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and
discard.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench.
4. Reinstallthe spark plug boot.
12
REPLACING THE LINE
1. Remove spool by firmly pulling on tap
button.
2. Clean entire surface of hub and spool.
3. Replace with a pre-wound spool, or cut two
lengths of 12-1/2 feet of 0.080" (2 mm) di-
ameter Poulan PRO brand line.
_WARNING: Never use wire, rope,
string, etc., which can break offand become a
dangerous missile.
4. Insert ends of the lines about 1/2 inch (1
cm) into the small holes on the inside of
spool.
/i Roles
Line exit holes Line in Notch
\
Line in Notch
Hub
5. Wind the line evenly and tightly onto the
spool. Wind in the direction of the arrows
found on the spool.
6. Push the lines into the notches, leaving 3
to 5 inches (7 - 12 cm) unwound.
7. Insert the lines into the the exit holes in
the hub as shown in the illustration.
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into
place.
10. Pull the lines extending outside ofthe hub
to release the lines from the notches.
REPLACING THE CUTTING HEAD
1. Align hole in the dust cup with the hole in
the side of the gearbox by rotating the
dust cup.
2. Insert a small screwdriver into aligned
holes. This will keep the shaft from turn-
ing while removing and installing trimmer
head.
Screwdriver _t_
3. While holding the screwdriver in position,
remove trimmer head by turning clock-
wise.
4. Thread replacement trimmer head onto
the shaft by turning counterclockwise.
Tighten until secure.
5. Remove the screwdriver.
CARBURETOR ADJUSTMENT
_il WARNING: Keepothers away when
making idle speed adjustments. The trimmer
head will be spinning during most of this pro-
cedure, Wear your protective equipment and
observe all safety precautions. After making
adjustments, the trimmer head must not
move/spin at idle speed,
The carburetor has been carefully set at the
factory, Adjustments may be necessary ifyou
notice any of the following conditions:
• Engine will not idle when the throttle is
released.
• The trimmer head moves/spins at idle.
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler.
Idle Speed Adjustment
Allow engine to idle. Adjust speed until engine
runs without trimmer head moving or spinning
(idle too fast) or stalling (idle speed too slow).
• Turn idle speed screw clockwise to
increase engine speed if engine stalls or
dies.
• Turn idle speed screw counterclockwise to
decrease engine speed if trimmer head
moves or spins at idle.
Ag&WARNING: Recheck the idle speed
after each adjustment, The trimmer head
must not move or spin at idle speed to avoid
serious injury to the operator or others.
Air Filter __
Cover -_
Idle Speed
Screw
If you require further assistance or are unsure
about performing this procedure, contact an
authorized service dealer or call
1-800-554-6723.
13
IIIWAI-(NINLi: Perform the following
steps after each use:
• Allow engh_e to cool before storing or trans-
porting.
Store unit and fuel h_a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
• Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
• Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
• Clean the entire unit before lengthy
storage.
• Store in a clean dry area.
• Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. PoF
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
HELPFUL TIP
During storage of your gas/ I
_j_'_ oilmixture, theeilwillsepa_ I
_i_ rate from the gas. I
_l_._J We recommend that you J
_'_4_fJ ahakethegaseanweekly I
to insure proper blending of J
the gas and oil. J
ENGINE
• Remove spark plug and pour 1 teaspoon of
40:1,2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
• Replace spark plug with new one of recom-
mended type and heat range.
• Clean air filter.
• Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
• At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
OTHER
• Do not store gasoline from one season to
another.
• Replace your gasoline can if itstarts to rust.
14
TROUBLESHOOTING TABLE
,_ WARNING: Aiways stop unit and disconnect spark plug before performing all ofthe
recommended remedies below except remedies that require operation of the unit,
TROUBLE
Engine will not
start.
CAUSE REMEDY
1. Move ON/OFF switch to ON.
1. ON/OFF switch in
OFF position.
2. Engine flooded.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
6. Carburetor requires
adjustment.
Engine wilt 1. Carburetor requires
not idle adjustment.
properly. 2. Crankshaft seals worn.
3. Compression low.
1. Air filter dirty.
2. Spark plug fouled.
Engine will not
accelerate,
lacks power.
or dies under
a load.
Engine
smokes
excessively.
Engine runs
hot.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
1. Choke partially on.
2. Fuel mixture incorrect.
3. Air filter dirty.
4. Carburetor requires
adjustment.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
2. See "Starting a Flooded Engine" in
Operation Section.
3. Fill tank with correct fuel mixture.
4. Instatl new spark plug.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6. Contact an authorized service dealer.
1. See "Carburetor Adjustment" in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
1.
2.
3.
4.
See "Fueling Engine" in Operation
section.
Replace with correct spark plug.
Contact an authorized service dealer.
Contact an authorized service dealer.
15
Poulan PRO warrants to the origh_al pur-
chaser that each new Poulan PRO brand
gasotine tool or attachment is free from de-
fects in material and workmanship and
agrees to repair or replace under this war-
ranty any defective gasoline product or at-
tachment as follows from the origh_al date of
purchase.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income produc-
ing purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use
of accessories and/or attachments not spe-
cifically recommended by Poulan PRO for
this tool Additionally, this warranty does not
cover tune-ups, spark plugs, filters, cutting
line, or rotating head parts that will wear and
require replacement with reasonable use dur-
ing the warranty period. This warranty does
not cover predefivery setup or normal adjust-
ments explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of Poulan PRO is to continuously
improve its products. Therefore, Poulan
PRO reserves the right to change, modify, or
discontinue models, designs, specifications,
and accessories of all products at any time
without notice or obligation to any purchaser.
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency, California Air Resources
Board, Environment Canada and Poulan/
WEED EATER are pleased to explain the
emissions control system warranty on your year
2005 and later small off-road engine, in Califor-
nia, all small off-road engines must be de-
signed, built, and equipped to meet the State's
stringent anti-smog standards. Poulan/
WEED EATER must warrant the emission
control system on your small off-road engine
for the periods of time listed below provided
there has been no abuse, neglect, or improp-
er maintenance of your small off- road engine.
Your emission control system includes parts
such as the carburetor and the ignition sys-
tem. Where a warrantable condition exists,
Poulan/WEED EATER wilt repair your small
off-road engine at no cost to you. Expenses
covered under warranty include diagnosis,
parts and labor. MANUFACTURER'S WAR-
RANTY COVERAGE: If any emissions re-
lated part on your engine (as listed under
Emissions Control Warranty Parts List) is de-
fective or a defect in the materials or workman-
ship of the engine causes the failure of such an
emission related part, the part will be repaired or
replaced by Poulan/WEED EATER. OWN-
ER'S WARRANTY RESPONSIBILITIES:
As the small off-road engine owner, you are
responsible for the performance of the re-
quired maintenance listed in your instruction
manual. Poulan/WEED EATER recommends
that you retain all receipts covering mainte-
nance on your small off-road engine, but
Poulan/WEED EATER cannot deny warranty
solely for the lack of receipts or for your failure
to ensure the performance of all scheduled
maintenance. As the small off-road engine
owner, you should be aware that Poulan/
WEED EATER may deny you warranty cov-
erage if your small off- road engine or a part of
it has failed due to abuse, neglect, improper
maintenance, unapproved modifications, or
the use of parts not made or approved by the
original equipment manufacturer. You are re-
sponsible for presenting your small off-road en-
gine to an PoulanAh/EED EATER authorized re-
pair center as soon as a problem exists.
Warranty repairs should be completed in a rea-
sonable amount of time, not to exceed 30 days.
Ifyou have any questions regarding your war-
ranty rights and responsibilities, you should
contact your nearest authorized service center
or call Poulan/WEED EATER at
1-800-554-6723. WARRANTY COM-
MENCEMENT DATE: The warranty period
begins on the date the small off-road engine
is purchased. LENGTH OF COVERAGE:
This warranty shall be for a period of two
years from the initial date of purchase. WHAT
IS COVERED: REPAIR OR REPLACE-
MENT OF PARTS. Repair or replacement of
any warranted part wil_ be performed at no
charge to the owner at an approved Poulan/
WEED EATER servicing center, if you have
any questions regarding your warranty rights
16
and responsibilities, you should contact your
nearest authorized service center or call Pou-
lan/WEED EATER at 1-800-554-6723,
WARRANTY PERIOD: Any warranted part
which is not scheduled for replacement as re-
quired maintenance, or which is scheduled
only for regular inspection to the effect of "re-
pair or replace as necessary" shall be war-
ranted for 2 years, Any warranted part which
is scheduled for replacement as required
maintenance shall be warranted for the period
of time up to the first scheduled replacement
point for that part. DIAGNOSIS: The owner
shall not be charged for diagnostic labor
which leads to the determination that a war-
ranted part is defective if the diagnostic work
is performed at an approved Poulan/WEED
EATER servich_g center, CONSEQUEN-
TIAL DAMAGES: Poulan/WEED EATER
may be liable for damages to other engine
components caused by the failure of a war-
ranted part still under warranty, WHAT IS
NOT COVERED: AH failures caused by
abuse, neglect, or improper maintenance are
not covered. ADD-ON OR MODIFIED
PARTS: The use of add-on or modified parts
can be ,qrounds for disallowh_q a warranty
claim. Poulan/WEED EATER is not liable to
cover failures of warranted parts caused by the
use of add-on or modified parts, HOW TO FILE
A CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service
center or call PoulanANEED EATER at
1-800-554-6723, WHERE TO GET WAR-
RANTY SERVICE: Warranty services or re-
pairs shall be provided at all Poulan/WEED
EATER service centers. Call:
1-800-554-6723. MAINTENANCE, RE-
PLACEMENT AND REPAIR OF EMISSION
RELATED PARTS: Any Poulan/WEED EAT-
ER approved replacement part used in the
performance of any warranty maintenance or
repair on emission related parts will be pro-
vided without charge to the owner if the part is
under warranty, EMISSION CONTROL
WARRANTY PARTS LIST: Carburetor, Igni-
tion System: Spark Plug (covered up to main-
tenance schedule), Ignition Module, Muffler
including catalyst, MAINTENANCE STATE-
MENT: The owner is responsible for the per-
formance of all required maintenance as de-
fined in the instruction manual,
The information on the product label indicates to which standard your engine is certified,
Example: (Year) EPA Phase Ior Phase II and/or CALIFORNIA.
41 I 61 I II 1
This engine is certified to be emissions compliant for the following use:
[] Moderate (50 hours)
[] Intermediate (125 hours)
[] Extended (300 hours)
17
Sotamente las siguientes combinaciones de herramieetas de jardineria con uso de cabeza
de motor a gasoiina y sus accesorios respectivos han sido Clasificadas pot los Underwriters
Laboratories, Inc, de acuerdo con los requisitos de seguridad aplicables.
Oabeza de motor con el acceaorio del cortadora ....................... PP136
Acceaorio opcional del propulsor de aire ........................... PP3OOOB
Acceaorio opcional del cortadora de malezaa ........................ PP4OOOC
El siguiente accesorio est#. Enlistado por Underwriter's Laboratories, Inc., de acuerdo con la
Norma UL 1602, "Motores a Gasolina, Miembro Rigido del Corte, Cortadoras de Bordes y
Recortadoras de Bordes."
Acceaorio opcional del cortadora de hordes ......................... PP10OOE
dI_ADVERTENClA: AI usar cualquier
herramieeta de fuerza de jard}eeria, deberan ob-
servarse precauciones basicas de seguirdad en
todo momento para reducir el riesgo de inceedio
y graves heridas. Lea y cumpla con todas las
instrucciones.
iEsta herramienta de fuerza puede set peli-
grosa! Cabe al usuario }e responsabilidad de
cumplir con todas las advertencias e iestruc-
ciones, iLea el manual de instrucciones en su
totalidad antes de usar el aparato! Este com-
pletamente familiarizado con los controtes y
con et uso correcto del aparato. Umite el uso
de este aparato a aquellas personas que hay-
an leido y comprendido, y que vayan a ob-
edecer, todas las adverteecias e instruc-
ciones tanto en el aparato como en el manual.
No permita nunca a los ni(_os que usen este
aparato.
¢ S
MANUAL DE INFORMACION DE
INSTRUCCIONES SEGURIDAD DEL
APARATO
.-&
PELIGRO: Nunca use sushillas con
accesorio del cortadora de linea. Nuncause
disposit}vos desgranadores con accesorios.
El aparato fue fiseSado para set usado exclu-
sivamente como cortodora de linea. El uso de
cualquier otto accesorios con accesorio det
cortadora de linea incremeetara el peligro de
heridas.
@OQ
dlJADVERTENClA: La linea de torte
arro_a objetos violentamente. Usted, al igual
que otras personas, puede quedar ciego o
herido. Use anteojos de seguridad y protec-
cion en las piernas. Mantenga todas las
partes del cuerpo alejadas de la lieea girante.
Use anteojos de seguridad
Botas
Mantenga a los niflos, los espectadores y ani-
males a una distancia minima de 15 metros
(50 pies). Pare el motor inmediatamente si aF
guiee se le acerca.
Si acontece alguna situacion no prevista en este
manual, tenga cuidado y use buee criterio. Si ne-
cesita ayud& entre ee contacto con su distribui-
dor autorizado del servicio o Ilame al
1-800-554-6723.
SEGURIDAD DEL USUARIO
• Vistase apropiadamente. Siempre use an-
teojos de seguridad o similar protecci6n
para los ojos cuando use o de mantenimiee-
to a este aparato (anteojos de seguridad
est_.n disponib}es). La proteccion para los
ojos se debe marcar con Z87.
• Siempre utilize mascarilla para ta cara o
mascarilla a prueba de polvo si se va a tra-
bajar en condiciones donde hay polvo.
• Siempre utilize pantalones pesados y lar-
gos, mangas largas, botas y guantes. Se re-
comienda el uso de pantorrilleras de seguri-
dad.
• Siempre utilize protecciSn para los pies. No
trabaje descalzo ni en sandaHas. Evite la
linea girante.
• Mantenga el cabello por encima de los hom-
bros, atandolo para tal efecto sies necesa-
rio. No use ropa suelta ni ropa con corbatas,
tiras, borlas, etc. que cuelgan libremente.
Puedee enredarse en las piezas ee movi-
miento.
• Siesta completament tapado, estar#, mas
protegido de los escombros y pedazos de
plantas tSxicos arrojados por la I_eea gi-
rante.
• Mantengasealerta. Nohagausodelapara-
to estando cat_sado, enfermo, trastomado o
bajo ta influencia del alcohol, de drogas o de
remedios. Vigile bien Io que est#. haciendo;
use del sentido comt_n.
• Use protecci6n de oidos.
18
• Nunca ponga el aparato en marcha ni Io
deje en marcha dentro de un recinto cerra-
do. Respirar los vapores del combustible _o
puede matar.
• Mantenga las manijas libres de aceite y de
combustible.
• Mantenga siempre el motor junto al lado
derecho de su cuerpo.
• Sostenga siempre el aparato con ambas
manos mientras este en funcionamiento.
• Mantengaelcabezaldecorte (ootrasacce-
sorios opcional) por debajo de la cintura y
iejos de todas las partes de su cuerpo. No
ievante el motor por encima de su cintura.
• Mantengatodas las partes de1cuerpo aleja-
das del silenciador y de ia iinea girante (o
otras accesotio opcional). Mantenga el mo-
tor por debajo del nivel de la cintura. El silen-
ciador puede causar graves quema- duras
cuando esta caliente.
• Mantenga el equiiibrio, con los pies en una
superficie estable. No se extienda demasia-
do o use el aparato desde superficies
inestables como esoaleras manuales,
arboles, cuestas empinadas, techos, etc.
• Use el aparato t_nicamente de dim o en luz
artificial fuerte.
• Use exclusivemente para trabajos descri-
tos en este manual (o el manual para acce-
sorios opcional).
SEGURIDAD DEL APARATO Y EN
EL MANTENIMIENTO
• Desconecte la bujia antes de hacer cualqui-
er mantenirniento menos tos ajustes at car-
burador.
• Inspeccione el aparato y cambie las piezas
daSadas o flojas antes de cada uso. Repare
toda fuga de combustible antes de usar el
aparato. Mantenga el aparato en buenas
condiciones de uso.
• Cambie todas las piezas del cabezal que
esten descantilladas, resquebrajadas, que-
bradas o daSadas de cualquier otro modo,
antes de usar el aparato.
• Haga el mantenimiento de1 aparato de
acuerdo a los procedimientos recomend-
ados. Mantenga la iinea de corte el largo
aprodiado.
• Use sotamente linea de diametro 2 mm
(0,080 de pulgada) de la marcha Poulan
PRO. Nunca use alambre, soga, hilo, etc.
• Instale la protector requerida antes de usar
su aparato. Use la bobina especificada.
AsegOrese que la bobina este correcta-
mente instalada y este bien fijo.
• Asegt3rese que el aparato este correcta-
mente armado como se muestra en el
manual.
• Haga tos ajustes ai carburador con el cabe-
zat apoyado de modo que la linea no pueda
tocar nada.
• Mantenga alejadas alas demas personas
siempre que haga ajustes al carburador,
• Use exclusivamente _os acoesorios y repues-
tos Poutan PRO recomendados.
• Todo servicio y mantinimiento no explicado
en este manual debera ser efectuado por un
disttibuidor autorizado del servicio.
SEGURIDAD CON EL COMBUSTIBLE
• Mezcle y vierta el combustible al mire fibre.
• Mantengalo alejado de las chispas y de las
llamas.
• Use recipiente aprobado para el combus-
tible.
• No fume ni permita que se fume cerca del
combustible ni del aparato ni mientras este
este en uso.
• Evite derramar el combustible o el aceite.
Limpie todo el combustible derramado.
• Alejese a por Io menos 3 metros (10 pies)
del lugar de abastecimiento antes de poner
en maroha el motor,
• Pare el motor y permita que se enfrie el apa-
rato antes de retirar la tapa del tanque.
• Almacene siempre combustible en un reci-
piente aprobado para los liquidos inflama-
bles.
TRANSPORTE Y ALMACENAMIENTO
• Espere que el motor se enfrie y fije bien el
aparato antes de quardarlo o de transpor-
tarlo en un vehicuio.
• Vacie el tanque decombustible antes de guar-
dar el aparato o de transportario. Consuma
todo el combustible restante en el carburador
poniendo el motor en marcha y dej_tndoio en
marcha hasta que le motor se pare solo.
• Guarde el aparato y el combustible en un lu-
gar donde los vapores del combustible no
puedan alcanzar chispas ni llamas prove-
nientes de los termotanques, los motores o
interruptores electricos, los calefactores
centra_es, etc.
• Guarde el aparato de modo que el cuchiHa
limitadora de linea no pueda causar heridas
accidentales. Se puede colgar el aparato
por la caja el eje de propulsion.
• Guarde el aparato fuera del alcance de los
nti_os.
AVlSO SPECIAL: El estar expuesto alas
vibraciones a traves del uso prolongado de
herramientas de fuerza a gasolina puede cua-
sar daf_os a los vasos sanguineos o a los ner-
vios de los dedos, las manos y las coyunturas
en aquellas personas que tienen propensidad
a los trastornos de la circulaci6n o alas hin-
chazones anormales. El uso prolongado en
tiempo frio ha sido asociado con daffos a los
vasos snaguineos de personas que por otra
parte se encuentran en perfecto estado de sa-
lud. Si ocurren sintomas tales como el entu-
mecimiento, el dolor, la falta de fuerza, los
cambios en el color o la textura de la piel o falta
de sentido en los dedos, las manos o las coy-
unturas, deje de usar esta m_tquina inmedia-
tamente y procure atenci6n medica. Los siste-
mas de anti-vibraci6n no garantizan que se
eviten tales problemes. Los usuarios que ha-
cen uso continuo y prolongando de las herra-
mientas de fuerza deben fiscalizar atenta-
mente su estado fisico y el estado del aparato.
AVISO ESPECIAL: Su aparato viene equi-
pada con silenciador limitador de temperatura
y con rejilla antichispa que cumpla los requisi-
tos de los C6digos de California 4442 y 4443.
Todas las tierras forestadas federales, mas
los estados de California, idaho, Maine, Min-
nesota, Nueva Jersey, Washington y Oreg6n,
requieren por ley que muchos motores de
19
combusti6nintemaestenequipadosconrejil-
laantichispa.Siustedelaparatoenunestado
yotraIocatidaddondeexistentalesreglamen-
tos,ustedtienelaresponsabilidadjuridicade
mantenerestaspiezasencorrectoestadode
funcionamiento.Delocontrario,estarAenin-
fracci6ndelatey.Paraelusonormalde1
dueifiodelacasa,elsilenciadorylarejilla
antichispanorequerirAnningOnservicio,
Despuesde50horasdeuso,recomendamos
quealsilenciadorseledeservicioosea
substituidopotundistribuidorautorizadodel
servicio,
SEGURIDAD AL RECORTAR
ADVERTENCIA: Inspeccione elArea
antes de cada uso. Retire los objetos (piedras,
vidrio roto, ctavos, alambre, etc.) que se puedan
enredar en la linea o que esta pueda arrojar. Los
objetos duros pueden daffiar el cabezal y este
los puede arrojar, causando graves heridas.
• Use el aparato exclusivamente para recortar,
para cortar cesped y para barrer. No 1o use
para cortar bordes, para podar ni para recortar
seto.
• Corte siempre de izquierda a derecha. Si se
corta con la linea del lado derecho del protec-
tor, los escombros volaran en sentido opuesto
al usuario.
REGLAS ADIOIONALES DE SE-
GURIDAD PARA ACCESORIOS
OPClONAL
_ADVERTENOIA: Para cada acce-
sorio opcional usada, lea a manual de instruc-
clones enteros antes de uso y siga todas las
advertencias e instrucciones en manual yen
la aooesorio.
_L.ADVERTENCIA: AsegQrese el
mango esta instalado al usar las accesorios al
cortar bordes o al cortadora de malezas.
Instale el mango sobre la flecha de la etiqueta
de seguridad del eje superior (extremo con el
motor del aparato). Si su accesorios del cortar
bordes o del cortadora de maiezas no inctuye
un mango, un kit de accesorio del mango
(#530071451 ) estA disponible de su distribui-
dor autorizado del servicio.
ango
SEGURIDAD AL CORTAR BORDES
_.ADVERTENCIA: Inspeecione el
Area a ser cortada antes de cada use. Retire
los objetos (piedras, vicrio roto, clavos,
alambre, hilo, etc.) que puedan ser arrojados
por la cuchilla o que puedan enroscarse en el
eje.
• La cuchilla continOa girando por un instante
despues de que se suelte el gatillo, La cu-
chilla puede herir gravemente al ususario o
a terceras.
• Dejeque la cuchilla se detenga antes desa-
cada del corte.
La cuchilla gira Deje que la cuchNa
pot un instanta se datenga antes
de sacarladel
despu#s de
que sahaya
so#ado
elgatfllo.
• Deseche toda cuchilla doblada, torcida,
resquebrajada, quebrada o da{_ada de cuaF
quier otro modo. Cambie todas las piezas
resquebrajadas, descantilladas o dafiadas
antes de usar el aparato,
• No intente remover el material y cortado o
sostenga eI material a ser cortado mientras
el motor se enouentre en marcha o cuando
el dispositivo que corta se encuentre en mo-
vimiento.
• Mantenga siempre las rueda y el calzo en
contacto con el suelo.
• Siempre empuje el aparato lentamente
sobre el terreno, Cuidese constantemente
contra las aceras desniveladas, hoyos en el
terreno, raices grandes, etc,
• Siempre use el mango al usando accesorio
al cortar bordes,
SEGURIDAD AL PROPULSOR DE
AIRE/ASPIRADORA
_IkADVERTENCIA: Inspeccione el
Area antes de poner en matodos los escom-
bros y objetos s61idos tales como piedras, vi-
drio, alambre, etc., que el aparato pueda arro-
jar atmire o hacer rebotar causando heridas de
este o cualquier otro modo durante el uso del
mismo.
• No apoye el aparato con el motor en marcha
en ninguna superficie que no este limpia o que
no sea s61ida. El aparato podria aspirar es-
combros tales como gavilia, arena, polvo,
cesped, etc. pot la entrada de aspiraeion y ar-
rojarlos por la salida de propulsion, dafiando el
aparato y/u otros objetos, o causando graves
heridas a espectadores o al usuario.
• Nunca cotoque objetos dentro de los tubos
de propulsiAn, tubos de aspiraci6n o salida
de mire; siempre dirija los escombros en di-
reccion contraria a donde personas, ani-
males, vidrierasu otros objetos sAtidos tales
como arboles, automoviles, paredes, etc.
se encuentran. La fuerza del mire puede ar-
rojar o hacer rebotar piedras, tierra o ramas,
hiriendo a personas o animales, rompiendo
vidrieras o causando otros dafios.
• Nunca ponga el aparato en marcha sin toner
todo el equipo correspondiente instalado. AI
usar el aparato como propulsor de mire,
sirmpre instale los tubes de propulsion.
• Inspeccione frecuentemente la abertura de
entrada de mire, los tubos de propulsion, y
los tubos de aspiraci6n siempre con el mo-
tor detenido y la bujia desconectada. Man-
tenga tas aberturas de ventilaci6n y los tu-
bos de descarga libres de escombros que
se pueden acumular y limitar la circulaci6n
debida de mire.
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
