Ibiza Light & Sound QUAD8-FX User manual

Page is loading ...

©Copyright LOTRONIC 2016 QUAD8-FX Page 2

BEFORE YOU BEGIN

Contents of the carton:

• 1 x Spider light effect

• 1x Mains lead

• 1x User Manual

• 2x omega clamps

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are

present and have been received in good condition. Notify the freight company immediately and retain packing

material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of

mishandling. Keep the carton and all packing materials. In the event that a fixture must be returned to the factory, it

is important that the fixture be returned in the original factory box and packing.

Safety Instructions

Please read these instructions carefully, they include important information about the installation, usage and

maintenance of this product.

• Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also receives

this instruction booklet.

• Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is

not higher than that stated on the decal or rear panel of the fixture.

• This product is intended for indoor use only!

It is essential that the device is earthed. A qualified person must carry out the electric connection.

• To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be

sure that no ventilation slots are blocked.

• Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse size

and type.

• Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use its carrying

handles.

• Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the fixture at temperatures higher than this.

• In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the same type of spare parts.

• Don’t connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the

disconnect device shall remain readily operable.

GB

©Copyright LOTRONIC 2016 QUAD8-FX Page 3

Specifications

Power supply .................................................................................................. 100-240Vac 50/60Hz

Consumption ............................................................................................................................ 80W

Light source ........................................................ 8x 10W LED (2x red, 2x green, 2x blue, 2x white)

Single beam angle ........................................................................................................................ 4°

Dimensions ....................................................................................................... 298 x 149 x 262mm

Weight ..................................................................................................................................... 3.5kg

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid

vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure

and able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times

the weight of the unit when installing the fixture.

The equipment must be fixed by professionals at a place where is out of the reach of people and where nobody can

pass by or under it.

ORIENTATION

This fixture may be mounted in any position provided there is adequate room for ventilation.

RIGGING

The LED moving head provides a unique mounting

bracket assembly that integrates the bottom of the base,

the included ‘omega bracket’ and the safety cable rigging

point in one unit (see the illustration on the right).When

mounting this fixture on a truss, be sure to use an

appropriate clamp with the included omega bracket using

a M10 screw fitted through the center hole of the ‘omega

bracket’. As an added safety measure, be sure to attach

at least one properly rated safety cable to the fixture

using one of the safety cable rigging points integrated in

the base assembly.

Fuse Replacement

Disconnect the power cord before replacing a fuse and always replace with the same type fuse.

With a flat head screwdriver wedge the fuse holder out of its housing.

Remove the damaged fuse from its holder and replace with exactly the same type of fuse.

Insert the fuse holder back in its place and reconnect power.

Data Cabling

To link fixtures together you must use data cables. If you choose to create your own cable, please use data-grade

cables that can carry a high quality signal and are less prone to electromagnetic interference.

CABLE CONNECTORS

Cabling must have a male XLR connector on one end and a female XLR connector on the other end.

©Copyright LOTRONIC 2016 QUAD8-FX Page 4

DMX connector configuration

Termination reduces signal errors. To avoid signal transmission problems and interference, it is always advisable to

connect a DMX signal terminator.

CAUTION

Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a

ground loop, and your fixture may perform erratically. Test cables with an ohm meter to check correct polarity and

to make sure the pins are not grounded or shorted to the shield or each other.

CONTROL PANEL

To access the main menu press the MENU button. Press the UP or DOWN

buttons until you reach function you wish to change. When you reach the

function you wish to change, press the ENTER button. When a function is

selected, use the UP or DOWN buttons to change the function settings.

Once your changes are made, press the ENTER button, and then press

and hold the MENU button for at least three seconds to confirm and lock the change into the system memory. To

exit without making any adjustments, press the MENU BUTTON. The display will lock after 30 secondes. Press the

MENU button for 3 seconds to unlock.

FUNCTION MENU

ADDR

001 - 512, DMX Address setting

CHND

11 ch

39 ch, select the channel mode

SLND

Mast

SL 1

SL 2 ( MASTER, SLAVEC OPTION)

SHND

SHOW 0 – SHOW 15, Select the show mode

AUTO

OFF

ON (Auto Mode)

SOUN

On – Off (SOUND CONTROL)

SENS

000 – 100 Sound sensitivity control (0 close, 100 The most sensitive)

TINT1

Yes - No (TIL Reverse)

TINT2

Yes - No (TIL Reverse)

LED

On - Off (Background LIGHT ON/OFF)

DISP

Disp

Dsip (Reverse Display)

TEST

Test

RSET

Reset

Settings

DMX Address Setting

1. Press the MENU, UP or DOWN button until “ADDR” is displayed, press ENTER.

INPUT

COMMON

DMX +

DMX-

Resistance 120 ohm

1/ 4w between pin 2

(DMX-) and pin 3

(DMX+) of the last

fixture.

©Copyright LOTRONIC 2016 QUAD8-FX Page 5

2. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired

address.

3. Press ENTER to confirm.

DMX channel mode

1. Press the MENU button until “CHND” is displayed, press ENTER. Either “10CH”, “38CH” will be displayed

2. Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confirm and exit.

SLND – Slave mode

To select Slnd, press the ENTER button to show the SLAVE MODE on the display. Use the DOWN/UP button to select

Mast (MASTER),Sl1 (SLAVE 1), Sl2 (SLAVE 2) modes. Once the mode has been selected, press the ENTER button to

confirm.

Show modes 0-15 (Factory programs).

Show mode can run with or without sound active mode active.

1. Press the MENU button until “SHND” is displayed, press ENTER.

2. “Sh X” will now be displayed, “X” representing a number between 0-15. Programs 1-15 are factory programs,

while “Sh 0” is random mode. Press the UP or DOWN buttons to find your desired show.

3. When you have found your desired show press ENTER, then press and hold the MENU button for at least 3

seconds to activate. After you have set your desired show, it can be changed at any time using the UP or DOWN

buttons.

AUTO program

1. Press the MENU button until “AUTO” is displayed, press ENTER.

2. The Display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” or “OFF”.

Sound Active mode

1. Press the MENU button until “SOUN” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to activate sound active

mode, or “OFF” to deactivate sound active mode.

3. Press ENTER, then press and hold the MENU button for at least 3 seconds to activate.

Sound sensitivity

1. Press the MENU button until “SENS” is displayed, press ENTER.

2. A number between 0-100 will be displayed. Press the UP or DOWN buttons to adjust the sound sensitivity. 0 being

the least sensitive and 100 being the most sensitive. When you have found your desired setting press ENTER to

confirm.

Tilt Inversion

1. Press the MENU button until “TINT” is displayed, press ENTER. Either “YES” or “NO” will be displayed.

2. To activate the Tilt inversion press the UP or DOWN buttons until YES is displayed, press ENTER to confirm. To

deactivate Tilt inversion, select NO and press Enter.

Display back light

1. Press the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to keep the LED display

on at all times, or “OFF” to switch to have the LED display switch off after 10 seconds.

3. Press ENTER and then press and hold the MENU button for at least three seconds to confirm.

©Copyright LOTRONIC 2016 QUAD8-FX Page 6

Display Reverse 180°

1. Press the either the MENU button until “DISP” is displayed, press ENTER.

2. Press the UP button to select “DSIP” to reverse the display, or “DISP” to change the display back.

3. Press ENTER to confirm.

Self test program

1. Press the MENU button until “TEST” is displayed, press ENTER.

2. The fixture will now run a self test. Press MENU to exit.

Reset

1. Press the MENU button until “Reset” is displayed. Press the ENTER button and the unit will reset itself.

DMX CHANNELS

11 channel definition table

Channel DMX Value Function

1 0---255 X motor route

2 0---255 Y1 motor route

3 0---255 Y2 motor route

4 0---255 Dimmer 0-100%

5

Strobe

000-007 Close strobe

008-015 Open strobe

016-131 Strobe from slow to fast

132-139 Open strobe

140-181 fast open slow close

182-189 Open strobe

190-231 Slow open fast close

232-239 Open strobe

240-247 Random strobe

248-255 open strobe

6 0---255 Red dimmer

7 0---255 Green dimmer

8 0---255 Blue dimmer

9 0---255 White dimmer

10 0---255 Y1, Y2 speed

11

000-007 Only others channels can be controlled

008-063 Auto run

064-127 Sound active

128-255 Reset

©Copyright LOTRONIC 2016 QUAD8-FX Page 7

39 channel definition table

Channel DMX Value Function

1 0---255 X motor route

2 0---255 Y1

3 0---255 Y2

4 0---255 Dimmer from 0-100%

5

000-007 Close strobe

008-015 Open strobe

016-131 Strobe from slow to fast

132-139 Open strobe

140-181 fast open slow close

182-189 Open strobe

190-231 Slow open fast close

232-239 Open strobe

240-247 Random strobe

248-255 open strobe

6 0---255 1 Red dimmer

7 0---255 1 Green Dimmer

8 0---255 1 Blue Dimmer

… 0---255 1 White Dimmer

33 … …

34 0---255 8 Red Dimmer

35 0---255 8 Green Dimmer

36 0---255 8 Blue Dimmer

37 0---255 8 White Dimmer

38 0---255 Y1, Y2 speed

39

000-007 Only others channels can be controlled

008-063 Auto run

064-127 Sound active

128-255 Reset

Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external lenses should be carried out periodically to

optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-side casing.

2. Clean the external optics with glass cleaner and a soft cloth every 20 days.

3. Always be sure to dry all parts completely before plugging the unit back in.

Page is loading ...

DMX KANALI

11 kanalni DMX način

Kanal DMX Vrednost Funkcija

1 0---255 X

2 0---255 Y1

3 0---255 Y2

4 0---255 Dimmer 0-100%

5

Strobe

000-007 Close strobe

008-015 Open strobe

016-131 Strobe from slow to fast

132-139 Open strobe

140-181 fast open slow close

182-189 Open strobe

190-231 Slow open fast close

232-239 Open strobe

240-247 Random strobe

248-255 open strobe

6 0---255 Red dimmer

7 0---255 Green dimmer

8 0---255 Blue dimmer

9 0---255 White dimmer

10 0---255 Y1, Y2 speed

11

000-007 Only others channels can be controlled

008-063 Auto run

064-127 Sound active

128-255 Reset

39 kanalni DMC način

Kanal DMX Vrednost Funkcija

1 0---255 X

2 0---255 Y1

3 0---255 Y2

4 0---255 Dimmer from 0-100%

5

Strobe

000-007 Close strobe

008-015 Open strobe

016-131 Strobe from slow to fast

132-139 Open strobe

140-181 fast open slow close

182-189 Open strobe

190-231 Slow open fast close

232-239 Open strobe

240-247 Random strobe

248-255 open strobe

6 0---255 Y1 Red dimmer

7 0---255 Y1 Green Dimmer

8 0---255 Y1 Blue Dimmer

… 0---255 Y1 White Dimmer

33 … …

34 0---255 8 Red Dimmer

35 0---255 8 Green Dimmer

36 0---255 8 Blue Dimmer

37 0---255 8 White Dimmer

38 0---255 Y1, Y2 speed

39

000-007 Only others channels can be controlled

008-063 Auto run

064-127 Sound active

128-255 Reset

Čiščenje

Zaradi ostankov megle, dima in praha čiščenja notranjih in zunanjih leč je treba izvajati redno za optimalno oddajanje

svetlobe.

1. Uporabite normalno čistilo za steklo in mehko krpo obrišite zunanjo-stransko ohišje.

2. Čiščenje zunanje optike s čistilom za steklo in mehko krpo vsakih 20 dni.

3. Vedno se prepričajte, da so posušeni vsi deli preden priključite enoto nazaj.

Za Slovenijo:

Page is loading ...

2. Limpie las optics externas con un paño ligeramente humedecido con limpia cristales clasico Y SEQUE

PERFECTAMENTE, cada tres semanas.

3. SEQUE TODO EL EQUIPO PERFECTAMENTE, ANTES DE VOLVER A ENCHUFARLO A LA CORRIENTE.

Imported from China by

LOTRONIC SA – Avenue Zénobe Gramme 9 – 1480 Saintes - Belgium

Ibiza Light & Sound QUAD8-FX User manual

This manual is also suitable for

Ibiza Light & Sound QUAD8-FX User manual

in other languages

Related papers

Other documents