DFI KB160 Reference guide
- Category
- Interface cards/adapters
- Type
- Reference guide
This manual is also suitable for
DC-in
+12V 4-pin
power (optional)
DisplayPort
SPI Flash
BIOS
1
2
1
ON
1
LAN 1
LAN 2
1
Chassis
Intrusion
1
1
SATA 0
1
SATA 1
Mini PCIe
1
210
9
1
210
9
1
210
9
1
210
9
1
1
2
Battery
1
LCD/Inverter
Power
Digital I/O
1
AMD
G-Series SoC
Digital I/O
Power
PS/2 Keyboard/Mouse
Power Select (JP5)
Clear CMOS
Data (JP1)
1
USB 2-3 Power
Select (JP12)
1
Dimming Mode
Select (JP10)
1
USB3.0 0-1
Power Select
(JP11)
1
1
1
Buzzer
21
39
40
1
12
11
12
USB 0-1
USB 0
USB 1
VGA
1
1
1
DIO 0-3
Output State
(JP15)
DIO Power
Select (JP14)
Backlight Power
Select (JP7)
Auto Power-on
Select (JP2)
EXC
EXC
Power
1
USB2.0 0-1
Power Select
(JP13)
USB 3.0
USB 2.0
LVDS Channel
and bpp Select
(SW1)
DIO 4-7
Output State
(JP16)
SATA 3.0
USB 2.0
910
12
USB 2-3
PTN3460
LVDS LCD
Panel
DDR3/DDR3L_1 SODIMM
DDR3/DDR3L_2 SODIMM
COM 1
COM 3
COM 2
COM 4
Front
Panel
1
2
5
6
Panel Power
Select (JP8)
System Fan
Standby
Power LED
12 24
113
19 20
1
4
ATX
Power
LCD/Inverter
Power Select
(JP9)
1
4
CPU Fan
12
ISL62771
SATA
Power 0
SATA
Power 1
LPC
1
12
2
11
LAN1 State
LAN2 State
LAN2 State
1
LAN1 State
2
78
SATA DOM
Power
Select
(JP6)
Note:
SATA1 supports SATA DOM.
PCIe x4
DFI Proprietary
Extension Bus
PS/2 Keyboard/Mouse Power Select JP5
+5V (default) 1-2 On
+5V_standby 2-3 On
LCD/Inverter Power Select JP9
+12V 1-2 On
+5V (default) 2-3 On
USB Power Select: 3.0 0-1 (JP11), 2-3 (JP12), 2.0 0-1 (JP13)
+5V (default) 1-2 On
+5V_standby 2-3 On
Clear CMOS Data JP1
Normal (default) 1-2 On
Clear CMOS Data 2-3 On
Digital I/O Power Select JP14
+5V 1-2 On
+5V_standby (default) 2-3 On
Panel Power Select JP8
+12V 1-2 On
+5V 3-4 On
+3.3V (default) 5-6 On
Auto Power-on Select JP2
Power-on via power button (default) 1-2 On
Power-on via AC power 2-3 On
KB160/KB161 Series
Switch 1
1 On 1 Off 2 On 2 Off
LVDS Channel and
bpp Select
Single LVDS Dual LVDS
VESA
(24bpp)
JEIDA or
VESA
(18bpp)
Digital I/O Output State:
DIO 0-3 (JP15), DIO 4-7 (JP16)
+5V or +5V_standby (default) 1-2 On
GND 2-3 On
Note:
1. SATA 1 supports SATA DOM.
2. JP5 will be used when an EXC board is installed into the EXC
interface on the motherboard for I/O expansion.
3. KB160 Series: 24-pin ATX power connector.
4. KB161 Series: 12V DC-in jack (default) or 4-pin power connector
(optional).
5. SATA power 0 and SATA power 1 are populated on the KB161
board only.
6. SATA 0 is not populated on the system board while the Mini PCIe
interface transmits the mSATA signal.
7. If you are installing one DDR3/DDR3L SODIMM only, make sure that
the SODIMM 2 socket must be populated fi rst.
SATA DOM Power Select JP6
GND (default) 1-2 On
+5V 2-3 On
Dimming Mode Select JP10
PWM Mode 1-2 On
Voltage Mode (default) 2-3 On
Backlight Power Select JP7
+3.3V (default) 1-2 On
+5V 2-3 On
The lithium ion battery powers the real-time clock and CMOS
memory. It is an auxiliary source of power when the main
power is shut off.
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend
by the manufacturer.
• Dispose of used batteries according to local ordinance.
Batterie:
• Danger d’explosion si la batterie n’est pas correctement
remplacée.
• Remplacez seulement avec le même type ou équivalent
recommandé par le fabricant.
• Traitez des batteries usées selon le règlement local.
Battery Usage
Safety Measures
Mesure de Sécurité de l’usage de Batterie
934-KB1601-0A0G
A30401402
Battery Notice
www.dfi .com
-
1
-
2
DFI KB160 Reference guide
- Category
- Interface cards/adapters
- Type
- Reference guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI