Monte Carlo Fan Company 4AAR13XXD Series Owner's Manual And Installation Manual

Brand: Monte Carlo Fan Company

Model: 4AAR13XXD Series

Category: Household fans

Type: Owner's Manual And Installation Manual

This manual is also suitable for

Monte Carlo Fan Company 4AAR13XXD Series is a ceiling fan with a light that can be used to cool a room or provide additional lighting. It comes with a remote control that allows you to adjust the fan speed and light settings from anywhere in the room. The fan has five different adjustable angles, so you can customize the airflow to your liking. It also has a safety cable that must be installed into the house structure beams using 3” lag screws, washers and lock washers provided. This ensures that the fan is securely mounted and will not fall in the event of a power outage or other emergency.

Owner’s Guide and Installation Manual

Total fan weight with light kit

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as your proof of purchase

To register your fixture, please visit our website www.montecarlofans.com

4AAR13XXD Series Fan

UL Model NO. : AC-542F602

8.53 kgs

18.77 lbs

shown with light

shown without light

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. UC7067RY manufac-

tured by Rhine Electronic Co., Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Cutomer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1/20/2012

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble). Remove the two outlet

box screws provided with the box,

aligning the holes of the mounting

bracket with the holes of the outlet box.

Re-install the 2 outlet box screws

securely.

Remove preassembled cross pin and keeper

pin from yoke at top of motor assembly and

partially loosen downrod set screws.

Place downrod over canopy, canopy bottom

cap, ﬁxed ring and yoke cover. Thread lead

wires and safety cable from motor assembly

through downrod.

Slip downrod into the yoke, align holes and

re-install cross pin and keeper pin. Re-tighten

downrod set screws on motor housing yoke.

Place yoke cover and ﬁxed ring onto motor

assembly and tighten the set screw on the ﬁx

ring with allen wrench provided.

Note: Refer to installation step 19 if you want

to replace downrod with longer one (not

included).

Make sure the orientation of fan assembly

you want and Install ball end of downrod

into mounting bracket opening.

Warning: Make sure the ball end of

downrod engages with mounting bracket

well to avoid personal injury.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod mode the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the leadwires are longer

than the cable and no stress is placed on

the leadwires.

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Mounting bracket

Canopy

Canopy bottom cap

Fixed ring

Yoke cover

Cross pin

Keeper

ping

Downrod set

screw

1/20/2012

7 8 9

10 11

Set dip switches on the Remote

Transmitter and Remote Receiver to the

same settings. This must be done so the

units will communicate properly. If you

have other fans you can set to control

from one Transmitter by setting

receivers the same as the Transmitter. If

you have more than one fan with remote,

you can set the dip switches to different

positions to have separate control.

Make wiring connections using wire

connectors provided as indicated above.

White from fan to white from remote

marked N. Blue from fan to blue from

remote marked light. Black from fan to

Black from remote marked L. White from

house to white from remote marked AC

N. Black from house to Black from

remote marked AC L. Connect all green

grounded wires to Grounded wire from

House. Make sure that no ﬁlaments are

outside of the wirenuts.

Insert the remote receiver into mounting

bracket.

Loosen one and remove one

preassembled canopy mounting screw

from mounting bracket. Save canopy

mounting screw. Lift canopy up, aligning

its keyhole slot with the preassembled

screws on mounting bracket and twist

clockwise to lock in place. Re-install the

removed canopy mounting screw and

tighten all screws securely.

Attach canopy bottom cap onto canopy

by aligning its notches with the

preassembled canopy mounting screws

on mounting bracket and twist clockwise

until tight.

Install 3 x 40 watt candelabra base bulbs.

Bulb included. Attach glass to light pan by

locating dimples in light pan with grooves

in glass and twist clockwise until tight.

WARNING: Over lamping the fan will

result in the fan lights shutting down until

the proper wattage of bulbs are installed.

Reset the lights by turning off, replace

bulbs with the correct wattage bulbs, turn

the power on.

Note: Do not replace bulb until it cools

down.

Note: Go to step 12 if you want to install

the fan without light

Loosen the knob by turning

counterclockwise (as arrow shown) for

the fan angle adjusting. Fasten the knob

when the fan is in position.

It can be adjusted with 5 different angles

and the fans at both sides can be

adjusted at different angles.

Dip switches

Wall switch

Black

White

Ground/Green

White

Blue

Black

For fan with light, go to

step 10.

For fan without light, go to

step 12.

arrow

Knob

1/20/2012

12 13 14

15 16 17

Disassemble light ﬁxture by removing 4

light ﬁxture set screws. Disconnect the

wires from fan assembly and the wires

from light ﬁxture.

Warning: Make sure main power is

turned off before handling light kit

disassembly.

Install blanking plate onto fan assembly

by turning clockwise.

Refer to installation step 11 for fan angle

adjusting.

Remove battery cover. Install 12V battery

into wall remote. Duracell MN21 /

Evereday A23 / GP 23A all 12V. Attach

cover of remote by placing over buttons

and snap the battery cover in place.

Place battery cover over battery

compartment and buttons. Place remote

over 2 pins on front cover. Attach cover

of remote by placing over 4 pins and

snapping into place.

Install wall control unit to outlet box using

machine screws provised.

Remove light pan by removing 3 light pan

set screws.

Battery cover

Battery

HAND HELD INSTALL

WALL MOUNT INSTALL

Light pan

Light ﬁxture

Blanking plate

Install fan without light

1/5/2012

Attach front cover to wall control unit with

screws provided. Snap battery cover in

place

If you want to replace downrod with

longer one (not included). Loosen the set

screw by allen wrench provided and

remove Pin and hanger ball from

downrod.

Place hanger ball on long downrod with

pin through downrod and seat in the slot

in hanger ball.

Tighten the set screw to hold downrod

with hanger ball securely.

Warning: Pin must be installed in slot

and through downrod

Downrod replacement

Downrod

Hanger ball

1/20/2012

FAN SPEED: Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan off press square”.

LIGHT ON/OFF: To turn light on, press light dimmer once quickly. To turn off press once quickly while light is on. To dim light hold

down button “light dimmer”. The light will cycle from bright to dim to bright until button is released. Light will maintain last setting if

turned off.

Remote Control Transmitter Features

MEDIUM SPEED

HIGH SPEED

LED LIGHT

LOW SPEED

FAN OFF SETTING

(Turn fan off only)

LIGHT ON/OFF SETTING AND

DIMMER (Press and hold to

dim light inﬁnitely)

1/20/2012

Trouble Shooting

,I\RXKDYHGLI¿FXOW\RSHUDWLQJ\RXUQHZFHLOLQJIDQLWPD\EHWKHUHVXOWRILQFRUUHFWDVVHPEO\LQVWDOODWLRQ

RUZLULQJ,QVRPHFDVHVWKHVHLQVWDOODWLRQHUURUVPD\EHPLVWDNHQIRUGHIHFWV,I\RXH[SHULHQFHDQ\IDXOWV

SOHDVHFKHFNWKLV7URXEOH6KRRWLQJ&KDUW,IDSUREOHPFDQQRWEHUHPHGLHGRU\RXDUHH[SHULHQFLQJGLI¿FXOW\LQ

LQVWDOODWLRQSOHDVHFDOORXU&XVWRPHU6HUYLFH&HQWHUDWWKH

QXPEHUSULQWHGRQ\RXUSDUWVOLVWLQVHUWVKHHW

Warning%HIRUHVHUYLFLQJ RU FOHDQLQJ XQLW 6ZLWFKSRZHU RII DW 6HUYLFH SDQHODQGORFNVHUYLFH GLVFRQQHFWLQJ

PHDQVWRSUHYHQWSRZHUIURPEHLQJVZLWFKHGRQDFFLGHQWDOO\:KHQWKHVHUYLFHGLVFRQQHFWLQJPHDQVFDQQRWEH

ORFNHGVHFXUHO\IDVWHQDSURPLQHQWZDUQLQJGHYLFHVXFKDVDWDJWRWKHVHUYLFHSDQHO

&KHFNPDLQDQGEUDQFKFLUFXLWIXVHVRUFLUFXLWEUHDNHUV

&KHFNOLQHZLUHFRQQHFWLRQVWRIDQDQGVZLWFKZLUHFRQQHFWLRQVLQVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRII

,IWKLVIDQXVHV PDQXDO IRUZDUGUHYHUVHVZLWFKPDNHVXUH WKH VZLWFK LV SXVKHG ¿UPO\

HLWKHUZD\)DQZLOOQRWRSHUDWHZKHQVZLWFKLVLQWKHPLGGOH

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

&KHFNWRPDNHVXUHDOOVFUHZVLQPRWRUKRXVLQJDUHVQXJQRWRYHUWLJKWHQHG

&KHFNWRPDNHVXUHWKHVFUHZVZKLFKDWWDFKWKHIDQEODGHKROGHUWRWKHPRWRUDUHWLJKW

&KHFNWRPDNHVXUHZLUHQXWFRQQHFWRUVLQVZLWFKKRXVLQJDUHQRWUDWWOLQJDJDLQVWHDFK

RWKHURUDJDLQVWWKHLQWHULRUZDOORIWKHVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRIIEHIRUHHQWHULQJVZLWFKKRXVLQJ

&KHFNWREHVXUHOLJKWEXOELVWLJKWLQVRFNHWDQGQRWWRXFKLQJWKHJODVVVKDGH

6RPHIDQPRWRUVDUHVHQVLWLYHWRVLJQDOVIURP6ROLG6WDWHYDULDEOHVSHHGFRQWUROV

$OORZEUHDNLQSHULRGRIKRXUV0RVWQRLVHVDVVRFLDWHGZLWKDQHZIDQZLOOGLVDSSHDU

DIWHUWKLVSHULRG

,IWKLVLV D GRZQURG PRXQWIDQPDNH VXUHWKDWWKH ULGJH RI WKHFDQRS\HQJDJHV WKH

QRWFKLQWKHGRZQURGEDOO

0DNHVXUH WKDW FDQRS\ PRXQWLQJ EUDFNHWRUPRXQWLQJSODWHDUH WLJKWHQHG VHFXUHO\ WR

FHLOLQJMXQFWLRQER[DQGMXQFWLRQER[LVPRXQWHG¿UPO\WRFHLOLQJMRLVW

&KHFNWKDWDOOEODGHVDUHVFUHZHG¿UPO\LQWREODGHKROGHUV

&KHFNWKDWDOOEODGHKROGHUVDUHWLJKWHQHGVHFXUHO\WRPRWRU

0RVWIDQZREEOHSUREOHPVDUHFDXVHGZKHQEODGHOHYHOVDUHXQHTXDO&KHFNWKLVOHYHOE\

VHOHFWLQJD SRLQWRQWKHFHLOLQJDERYHWKH WLSRIRQH RIWKH EODGHV0HDVXUHWKLV GLVWDQFH

IURPEODGHWLSWRFHLOQJ.HHSLQJPHDVXUHZLWKLQURWDWHWKHIDQXQWLOWKHQH[WEODGH

LVSRVLWLRQHGIRUPHDVXUHPHQW5HSHDW IRUHDFKEODGH,I DOO EODGH OHYHOV DUH QRWHTXDO

\RXFDQDGMXVWEODGHOHYHOVE\WKHIROORZLQJSURFHGXUH7RDGMXVWDEODGHWLSGRZQLQVHUW

DZDVKHUQRW VXSSOLHG EHWZHHQ WKHEODGHDQGEODGH KROGHU DW WKH VFUHZFORVHVWWRWKH

PRWRU7RDGMXVWDEODGHWLSXSLQVHUWZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGH

KROGHUDWWKH WZR VFUHZV IDUWKHVW IURP WKHPRWRU5HYHUVHWKH SRVLWLRQ RI WKH ZDVKHULI

EODGHVPRXQWIURPWRSRIEODGH

,IEODGHZREEOH LVVWLOO QRWLFHDEOHLQWHUFKDQJLQJWZRDGMDFHQWVLGH E\VLGHEODGHVFDQ

UHGLVWULEXWHWKHZHLJKWDQGSRVVLEO\UHVXOWLQVPRRWKHURSHUDWLRQ

&KHFNEOXHZLUHIURPIDQWRPDNHVXUHLWLVFRQQHFWHGWRKRWZLUHIURPKRXVH

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQIDQVZLWFKKRXVLQJ

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQOLJKWNLW

&KHFNIRUIDXOW\OLJKWEXOEDQGPDNHVXUHEXOELVWLJKWLQVRFNHW

5HPRYHOLJKWNLWDQGFKHFNWKHSOXJFRQQHFWLRQVLIWKH\DUHSUHVHQW

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

CAUTION0DNH VXUH PDLQSRZHULVWXUQHG RII EHIRUH HQWHULQJ VZLWFKKRXVLQJDQGRU

FDQRS\

WARNING:

2YHUODPSLQJWKHIDQZLOOUHVXOWLQWKHIDQOLJKWVVKXWWLQJGRZQXQWLOWKHSURSHU

ZDWWDJHRIEXOEVDUHLQVWDOOHG5HVHWWKHOLJKWVE\WXUQLQJRIIUHSODFHEXOEVZLWKWKHFRUUHFW

ZDWWDJHEXOEV7XUQSRZHURQ

,IIDQVRXQGVQRLV\

,IIDQZREEOHV

,IOLJKWGRHVQRWZRUN

,IIDQGRHVQRWVWDUW

Trouble Suggested Remedy

Mar.2012

Monte Carlo Fan Company 4AAR13XXD Series Owner's Manual And Installation Manual

Brand: Monte Carlo Fan Company

Model: 4AAR13XXD Series

Category: Household fans

Type: Owner's Manual And Installation Manual

This manual is also suitable for

Download PDF

report

Monte Carlo Fan Company 4AAR13XXD Series Owner's Manual And Installation Manual

This manual is also suitable for

Monte Carlo Fan Company 4AAR13XXD Series Owner's Manual And Installation Manual

Related papers

Other documents