Panasonic TH-42PH10RK Operating Instructions Manual

Category
Plasma TVs
Type
Operating Instructions Manual
T
H
-
4
2
P
S
9
TH-42PS9
Please read these instructions before operating your set
and retain them for future reference.
Model No.
Operating Instructions
Progressive Wide Plasma Display
English
The illustration shown is an image.
TH-42PS10RK
TH-42PS10RS
Model No.
High De nition Plasma Display
TH-42PH10RK
TH-42PH10RS
TH-50PH10RK
TH-50PH10RS
TH-58PH10RK
ME67
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
2
Dear Panasonic Customer
Welcome to the Panasonic family of customers. We hope that you will have many years of
enjoyment from your new Plasma Display.
To obtain maximum benefit from your set, please read these Instructions before making
any adjustments, and retain them for future reference.
Retain your purchase receipt also, and note down the model number and serial number of
your set in the space provided on the rear cover of these instructions.
Visit our Panasonic Web Site http://panasonic.net
Table of Contents
Important Safety Notice ........................................... 3
Safety Precautions ................................................... 4
Accessories .............................................................. 7
Accessories Supply ................................................. 7
Remote Control Batteries ........................................ 7
Connections .............................................................. 8
PC Input Terminals connection ................................ 9
SERIAL Terminals connection ............................... 10
AV connection (for TH-42PH10RK/S, TH-50PH10RK/S,
TH-58PH10RK)
..................................................... 11
Power On / Off ......................................................... 12
Initial selections ..................................................... 13
Selecting the input signal ...................................... 13
Selecting the On-Screen Menu Language ............ 13
Basic Controls ........................................................ 14
On-Screen Menu Displays ..................................... 16
ASPECT Controls ................................................... 18
Adjusting Pos. / Size .............................................. 19
MULTI PIP ................................................................ 20
Advanced PIP .......................................................... 21
Picture Adjustments ............................................... 22
Advanced settings ................................................. 23
Sound Adjustment .................................................. 25
Mute ...................................................................... 25
Digital Zoom ............................................................ 26
PRESENT TIME Setup / Set up TIMER .................. 27
PRESENT TIME Setup .......................................... 27
Set up TIMER ........................................................ 28
Screensaver (For preventing image retention) .... 29
Setup of Screensaver Time ................................... 30
Reduces screen image retention ........................... 30
Side Panel Adjustment .......................................... 31
Reduces power consumption ............................... 32
Customizing the Input labels ................................. 32
Setup for MULTI DISPLAY ...................................... 33
(For TH-42PS10RK/S)
How to Setup MULTI DISPLAY ............................. 33
How to set the display location number
for each Plasma Display ....................................... 34
(For TH-42PH10RK/S, TH-50PH10RK/S, TH-58PH10RK)
How to Setup MULTI DISPLAY ............................. 35
How to set the display location number
for each Plasma Display ....................................... 35
F (Seam hides video) Setting ................................ 37
ID Remote Control Function .................................. 37
Setup for Input Signals .......................................... 38
Component / RGB-in select ................................... 38
3D Y/C Filter .......................................................... 38
Colour system / Panasonic Auto ........................... 39
Cinema reality / P-NR ............................................ 39
Sync ...................................................................... 40
Refresh Rate (for TH-42PH10RK/S, TH-50PH10RK/S,
TH-58PH10RK) ..................................................... 40
H-Freq. (kHz) / V-Freq. (Hz) .................................. 40
Options Adjustments ............................................. 41
Weekly Command Timer (for TH-42PH10RK/S,
TH-50PH10RK/S, TH-58PH10RK) ........................ 48
Shipping condition ................................................. 50
Troubleshooting ..................................................... 51
VIDEO/PC input signals ......................................... 52
Command list of Weekly Command Timer ........... 53
Speci cations ......................................................... 54
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
3
Important Safety Notice
Trademark Credits
VGA is a trademark of International Business Machines Corporation.
Macintosh is a registered trademark of Apple Computer, USA.
S-VGA is a registered trademark of the video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been
fully respected.
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention
to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3
mode.
WARNING
1) To prevent damage which may result in re or shock hazard, do not expose this appliance to dripping
or splashing.
Do not place containers with water ( ower vase, cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
No naked ame sources, such as lighted candles, should be placed on / above the set.
2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to quali ed
service personnel.
3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type
power plug. This plug will only t an earthing-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the earthing plug.
4) To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.
CAUTION
This appliance is intended for use in environments which are relatively free of electromagnetic elds.
Using this appliance near sources of strong electromagnetic elds or where electrical noise may overlap with the
input signals could cause the picture and sound to wobble or cause interference such as noise to appear.
To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic elds.
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
4
Safety Precautions
WARNING
Setup
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Matsushita Electric Industrial Co., Ltd.)
• Speakers ..................................................... TY-SP42P8W-K (TH-42PS10RK, TH-42PH10RK),
TY-SP42P8W-S (TH-42PS10RS, TH-42PH10RS),
TY-SP50P8W-K (TH-50PH10RK),
TY-SP50P8W-S (TH-50PH10RS),
TY-SP58P10WK (TH-58PH10RK)
• Pedestal ...................................................... TY-ST07-K (TH-42PS10RK, TH-42PH10RK, TH-50PH10RK),
TY-ST07-S (TH-42PS10RS, TH-42PH10RS, TH-50PH10RS),
TY-ST08-K (TH-42PS10RK, TH-42PH10RK, TH-50PH10RK),
TY-ST08-S (TH-42PS10RS, TH-42PH10RS, TH-50PH10RS),
TY-ST58-K (TH-58PH10RK)
• Mobile stand ................................................
TY-ST42PF3 (TH-42PS10RK/S, TH-42PH10RK/S, TH-50PH10RK/S),
TY-ST58PF10
• Wall-hanging bracket (vertical) .................... TY-WK42PV7
• Wall-hanging bracket (angled) .................... TY-WK42PR7
• Wall-hanging bracket (drawer type) ............ T
Y-WK42DR1 (TH-42PS10RK/S, TH-42PH10RK/S, TH-50PH10RK/S)
• Ceiling-hanging bracket .............................. TY-CE42PS7 (TH-42PS10RK/S, TH-42PH10RK/S, TH-50PH10RK/S)
• BNC Component Video Terminal Board ...... TY-42TM6A
• BNC Composite Video Terminal Board ....... TY-42TM6B
• BNC Dual Video Terminal Board ................. TY-FB9BD
• SCART Terminal Board ............................... TY-FB8SC
• RCA Component Video Terminal Board ...... TY-42TM6Z
• RCA Composite Video Terminal Board ....... TY-42TM6V
• RGB (Digital) Terminal Board ...................... TY-42TM6D
• RGB Active Through Terminal Board .......... TY-42TM6G
• PC Input Terminal Board ............................. TY-42TM6P
Composite / Component Video Terminal Board
... TY-42TM6Y
• SDI Terminal Board ..................................... TY-FB7SD
• HD-SDI Terminal Board ............................... TY-FB9HD
• HDMI Terminal Board .................................. TY-FB8HM
• Ir Through Terminal Board .......................... TY-FB9RT
• U/V Tuner Board with Hospitality Port ......... TY-FB9TE (TH-50PH10RK/S, TH-58PH10RK)
• Set Up Loader ............................................. TY-RM09SL (TH-50PH10RK/S, TH-58PH10RK)
• AV Terminal Box .......................................... TY-TB10AV
• Touch Panel ................................................ TY-TP42P8-S (TH-42PS10RK/S, TH-42PH10RK/S),
TY-TP50P8-S (TH-50PH10RK/S), TY-TP50P10S (TH-50PH10RK/S),
TY-TP42P10S (TH-42PS10RK/S, TH-42PH10RK/S),
TY-TP58P10S (TH-58PH10RK)
• Anti glare lter ............................................. TY-AR50P9W (TH-50PH10RK/S),
TY-AR42P9W (TH-42PS10RK/S, TH-42PH10RK/S),
TY-AR58P10W (TH-58PH10RK)
Always be sure to ask a quali ed technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from
being played with by young children, creating the potential risk of suffocation.
Do not place the Plasma Display on sloped or unstable surfaces.
The Plasma Display may fall off or tip over.
Do not place any objects on top of the Plasma Display.
If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result
in re or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic
dealer.
Transport only in upright position!
Transporting the unit with its display panel facing upright or downward may cause damage to the internal
circuitry.
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
5
Safety Precautions
Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table
cloths and curtains.
For suf cient ventilation;
If using the pedestal (optional accessory) for the Plasma Display, leave a space of at least 10 cm at the
top, left and right, at least 6 cm at the bottom, and at least 7 cm at the rear. If using some other setting-up
method, leave a space of at least 10 cm at the top, bottom, left and right, and at least 7 cm at the rear.
When using the Plasma Display
The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz.
Do not cover the ventilation holes.
Doing so may cause the Plasma Display to overheat, which can cause re or damage to the Plasma Display.
Do not stick any foreign objects into the Plasma Display.
Do not insert any metal or ammable objects into the ventilations holes or drop them onto the Plasma Display, as
doing so can cause re or electric shock.
Do not remove the cover or modify it in any way.
High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection,
adjustment and repair work, please contact your local Panasonic dealer.
Ensure that the mains plug is easily accessible.
Do not use any power supply cord other than that provided with this unit.
Doing so may cause re or electric shocks.
Securely insert the power supply plug as far as it will go.
If the plug is not fully inserted, heat may be generated which could cause re. If the plug is damaged or the wall
socket is loose, they shall not be used.
Do not handle the power supply plug with wet hands.
Doing so may cause electric shocks.
Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug
body, not the cable.
Do not damage the cable, make any modi cations to it, place heavy objects on top of it, heat it, place it near any
hot objects, twist it, bend it excessively or pull it. To do so may cause re and electric shock. If the power cable is
damaged, have it repaired at your local Panasonic dealer.
If the Plasma Display is not going to be used for any prolonged length of time, unplug the power supply plug
from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out
from the Plasma Display, immediately unplug the power supply plug from the wall outlet.
If you continue to use the Plasma Display in this condition, re or electric shock could result. After checking that
the smoke has stopped, contact your local Panasonic dealer so that the necessary repairs can be made. Repairing
the Plasma Display yourself is extremely dangerous, and shall never be done.
If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet
becomes damages, disconnect the power supply plug immediately.
A short circuit may occur, which could cause re. Contact your local Panasonic dealer for any repairs that need to
be made.
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
6
Safety Precautions
CAUTION
When using the Plasma Display
Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.
Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands
or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.
Be sure to disconnect all cables before moving the Plasma Display.
If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged,
and re or electric shock could result.
Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any
cleaning.
Electric shocks can result if this is not done.
Clean the power cable regularly to prevent it becoming dusty.
If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in re.
Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.
This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment.
Install your infrared sensor in a place away from direct or re ected light from your Plasma Display.
Cleaning and maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in
which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until
the surface is dry.
• Do not scratch or hit the surface of the panel with ngernails or other hard objects, otherwise the surface may
become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner,
otherwise the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been
added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get
inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the
cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods
in contact with articles made from rubber or PVC.
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
+
+
-
-
7
Accessories
Power supply cord Fixing bands × 2
Batteries for the Remote
Control Transmitter
(2 × R6 (UM3) Size)
Remote Control Transmitter
EUR7636090R
Operating Instruction book
Accessories Supply
Check that you have the accessories and items shown
Remote Control Batteries
Requires two R6 batteries.
1. Pull and hold the hook, then open
the battery cover.
2. Insert batteries - note correct
polarity ( + and -).
3. Replace the cover.
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline
batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precaution:
1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5.
Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.
“R6 (UM3)” size
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
SLOT1
1
2
1
2
1
2
SERIAL PC IN
AUDIO
SLOT2 SLOT3
VIDEO
AUDIO
R L
AUDIO
R L
AV IN B A
S VIDEO
8
Connections
SPEAKERS
Terminals (R)
SPEAKERS
Terminals (L)
When connecting the speakers, be sure to use only the optional accessory speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
(Example: TH-42PH10RK)
AC cord connection
(see page 12)
Speakers (Optional accessories)
– Cable xing bands Secure any excess cables with bands as required.
Pass the attached cable
xing band through the clip
as shown in the gure.
To secure cables connected to Terminals, wrap the cable xing band around them
then pass the pointed end through the locking block, as shown in the gure.
While ensuring there is suf cient slack in cables to minimize stress (especially
in the power cord), rmly bind all cables with the supplied xing band.
To tighten: To loosen:
Pull
Pull
Push the catch
– AC cord xing
Notes:
On TH-42PH10RK/S, TH-50PH10RK/S and TH-58PH10RK, terminal board is installed in SLOT 1 at factory shipment.
On TH-42PS10EK/S, SLOT 1-3 are all empty at factory shipment.
Dual Video Terminals (equivalent
of BNC Dual Video Terminal Board
(TY-FB9BD)) (see page 11)
From EXTERNAL
monitor terminal on
Computer (see page 9)
From SERIAL Terminal
on Computer
(see page 10)
Optional Terminal
Board Insert Slot
(covered)
Note:
Make sure that the AC cord is locked
on both the left and right sides.
Plug the AC cord into the display unit.
Plug the AC cord until it clicks.
Unplug the AC cord
Unplug the AC cord
pressing the two
knobs.
Note:
When disconnecting the AC cord, be
absolutely sure to disconnect the AC
cord plug at the socket outlet rst.
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
AUDIO
PC IN
TH-42PS9
1
678
3
9
45
10
15 14 13 12 11
2
9
Connections
Notes:
• Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input
Terminal.
Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
The display resolution is a maximum of 640 × 480 dots (TH-42PS10RK/S), 768 × 768 dots (TH-42PH10RK/S),
1,024 × 768 dots (TH-50PH10RK/S, TH-58PH10RK) when the aspect mode is set to “4:3”, and 852 × 480 dots (TH-
42PS10RK/S), 1,024 × 768 dots (TH-42PH10RK/S), 1,366 × 768 dots (TH-50PH10RK/S, TH-58PH10RK) when the
aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show ne
detail with suf cient clarity.
The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will
need to make setting changes to the computer at the time of connection.
Some PC models cannot be connected to the set.
There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
The computer shown in the illustration is for example purposes only.
Additional equipment and cables shown are not supplied with this set.
Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speci ed
frequency range.
Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.
Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”
(when Component connection) or “RGB” (when RGB signal connection). (see page 38)
Signal Names for Mini D-sub 15P Connector
Pin Layout for PC Input
Terminal
PC Input Terminals connection
COMPUTER
Conversion adapter
(if necessary)
Mini D-sub 15p
RGB
PC cable
Stereo plug
Audio
Connect a cable which matches
the audio output terminal on the computer.
Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name
1
R (PR/CR)
6
GND (Ground)
11
NC (not connected)
2
G (Y)
7
GND (Ground)
12
SDA
3
B (PB/CB)
8
GND (Ground)
13
HD/SYNC
4
NC (not connected)
9
NC (not connected)
14
VD
5
GND (Ground)
10
GND (Ground)
15
SCL
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
6789
13452
SERIAL
10
SERIAL Terminals connection
Notes:
Use the RS-232C cable to connect the computer to the Plasma Display.
The computer shown is for example purposes only.
Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface speci cation, so that the Plasma Display can be controlled
by a computer which is connected to this terminal.
The computer will require software which allows the sending and receiving of control data which satis es the conditions
given below. Use a computer application such as programming language software. Refer to the documentation for
the computer application for details.
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
Connections
Pin layout for SERIAL Terminal
Basic format for control data
The transmission of control data from the computer
starts with a STX signal, followed by the command,
the parameters, and lastly an ETX signal in that order.
If there are no parameters, then the parameter signal
does not need to be sent.
Notes:
If multiple commands are transmitted, be sure to wait
for the response for the rst command to come from
this unit before sending the next command.
• If an incorrect command is sent by mistake, this
unit will send an “ER401” command back to the
computer.
• SL1A, SL1B, SL2A and SL2B of Command IMS are
available only when a dual input terminal board is
attached.
With the power off, this display responds to PON command
only.
COMPUTER
RS-232C Straight cable
D-sub 9p
Start
(02h)
3-character
command (3 bytes)
Colon Parameter(s)
(1 - 5 bytes)
End
(03h)
STX C1 C2 C3 P1 P2 P3 P4:P5ETX
Signal level RS-232C compliant
Synchronization method Asynchronous
Baud rate 9600 bps
Parity None
Character length 8 bits
Stop bit 1 bit
Flow control -
RS-232C Conversion cable
D-sub 9-pin female Details
2
R X D
3
T X D
5
GND
4
6
Non use
7
8
Shorted
1
9
NC
Command Parameter Control details
PON None Power ON
POF None Power OFF
AVL ** Volume 00 - 63
AMT
0 Audio MUTE OFF
1 Audio MUTE ON
IMS None
SL1
SL2
SL3
PC1
SL1A
SL1B
SL2A
SL2B
Input select (toggle)
Slot1 input
Slot2 input
Slot3 input
PC input
Slot1 input (INPUT1A)
Slot1 input (INPUT1B)
Slot2 input (INPUT2A)
Slot2 input (INPUT2B)
DAM None
NORM
ZOOM
FULL
JUST
SELF
Screen mode select (toggle)
NORMAL (4 : 3)
ZOOM
FULL
JUST
Panasonic AUTO
Communication parameters
Command
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
SLOT3SLOT2
PC IN
SLOT1
VIDEO
AUDIO
RL
AUDIO
RL
AV IN
S VIDEO
VIDEO
OUT
S VIDEO
OUT
AUDIO
OUT
RL
AUDIO
OUT
RL
BA
This unit has a terminal board equivalent to BNC Dual Video Terminal Board (TY-FB9BD) as standard equipment.
11
Connections
Note:
Additional equipment, cables and adapter plugs shown are not supplied with this set.
S VIDEO VCR
CAMCORDER
VCR
Example of input signal source
AV connection (for TH-42PH10RK/S, TH-50PH10RK/S, TH-58PH10RK)
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
INPUT MENU ENTER/+/VOL
-
/
TH-42PS9
Italiano
Español
ENGLISH (US)
Русский
English (UK)
Deutsch
Français
OSD Language
SetSelect
PC
16:9
12
Power On / Off
Power Indicator
Remote Control
Sensor
Connecting the plug to the Wall Outlet
Notes:
Main plug types vary between countries. The power plug shown
at right may, therefore, not be the type tted to your set.
When disconnecting the AC cord, be absolutely sure to
disconnect the AC cord plug at the socket outlet rst.
Press the Power switch on the Plasma Display to turn the set
on: Power-On.
Power Indicator: Green
Example: The screen below is displayed for a while after the
Plasma Display is turned on (setting condition is an
example).
When the Power is turned on for the rst
time, the Language selection screen is
displayed.
From the second time on, language
selection can be done from the setup
menu. (see page 13)
Select the desired language using the
or button and press the ACTION (
)
button.
Note:
Set with the remote control. Buttons on the
main unit are unavailable for this setting.
From the second time on, the below
screen is displayed for a while (setting
condition is an example).
Press the button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the switch on the
unit, when the Plasma Display is on or in standby mode.
Note:
During operation of the power management function, the power indicator turns
orange in the power off state.
Connecting the AC cord plug to the Plasma Display.
Fix the AC cord plug securely to the Plasma
Display with the clamper. (see page 8)
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
.......(Japanese)
.......(Russian)
Русский
.......(Chinese)
Italiano
Français
Deutsch
English(UK)
Español
ENGLISH(US)
1/2
Signal
PC
Off
Standby save
Off
Power management
Off
Auto power off
Off
OSD Language English
(
UK
)
Component/RGB-in select
RGB
Input label
Power save
Setup
INPUT MENU ENTER/
+
/VOL
-
/
INPUT MENU ENTER/
+
/VOL
-
/
TH-42PS9
13
Initial selections
Selecting the On-Screen Menu Language
Press to display the Setup menu.
Press to select the OSD Language.
Press to select your preferred language.
Selectable languages
Notes:
Selecting is also possible by pressing the INPUT button on the unit.
Input terminal will not be selected if the terminal board is not installed into the
SLOT.
Select to match the signals from the source connected to the component/RGB input
terminals. (see page 38)
In 2 screen display, the same input mode cannot be selected for the main picture
and sub picture.
Selecting the input signal
Select the input signals to be connected by installing the optional Terminal Boards.
Press to select the input signal to be played back from
the equipment which has been connected to the Plasma
Display.
Input signals will change as follow:
INPUT1 INPUT2 PCINPUT3
• TH-42PS10RK/S
• TH-42PH10RK/S, TH-50PH10RK/S, TH-58PH10RK
INPUT1A INPUT1B INPUT2 PCINPUT3
SLOT1 is for dual input so that you can select INPUT1A
or INPUT1B for INPUT1.
INPUT1A : VIDEO signal terminal in SLOT1
INPUT1B : S-VIDEO signal terminal in SLOT1
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
INPUT MENU ENTER/
+
/VOL
-
/
On
Surround
14
Basic Controls
Main Power On / Off Switch
Power Indicator
The Power Indicator will light.
Power-OFF .... Indicator not illuminated (The unit
will still consume some power
as long as the power cord is still
inserted into the wall outlet.)
• Standby .......... Red
• Power-ON ...... Green
• DPMS .............Orange (With PC input signal
and during operation of PC’s
screensaver.)
Volume Adjustment
Volume Up “+” Down “–”
When the menu screen is
displayed:
“+”: press to move the cursor
up
“–”: press to move the cursor
down
(see page 16)
Enter / Aspect button
(see page 16, 18)
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu
screen will switch. (see page 16)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
(see page 13)
Normal Viewing Picture Setup
Sound Pos. /Size
Remote control sensor
SURROUND button
The surround setting switches on and off each time
the SURROUND button is pressed.
The bene ts of surround sound are enormous. You
can be completely enveloped in sound; just as if
you were at a concert hall or cinema.
Note:
The surround settings are memorized separately
for each Sound Mode (Normal, Dynamic, Clear).
On Off
N button (see page 19, 22, 23, 24, 25)
POS. / SIZE button (see page 19)
PICTURE button (see page 22)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
Press to select INPUT1, INPUT2, INPUT3 and PC input
SLOTS sequentially. (see page 13)
Sound mute On / Off (see page 25)
Numeric buttons (see page 37)
ASPECT button
Press to adjust the aspect. (see page 18)
MULTI Window buttons (see page 20)
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
15
Basic Controls
Standby (ON / OFF) button
The Plasma Display must rst be plugged into the wall outlet and turned on at the power switch (see page 12).
Press ON to turn the Plasma Display On, from Standby mode. Press OFF to turn the Plasma Display Off
to Standby mode.
SET UP button (see page 16, 17)
DIRECT INPUT buttons
Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to
select the input mode.
This button is used to switch directly to INPUT mode.
These buttons can only display the slot which is installed. If you
press the button whose slot is not installed, it automatically displays
the current input signal.
When a dual input terminal board is attached, A or B is displayed
depending on the selected input signal. (Ex. INPUT1A, INPUT1B)
Notes:
For TH-42PH10RK/S, TH-50PH10RK/S and TH-58PH10RK, press
to switch the input mode between INPUT1A and INPUT1B.
Image retention (image lag) may occur on the plasma display panel when
a still picture is kept on the panel for an extended period. The function that
darkens the screen slightly is activated to prevent image retention (see
page 51), this function is not the perfect solution to image retention.
Channel Adjustment
This button cannot be used for this model.
Volume Adjustment
Press the Volume Up “+” or Down “–” button to increase or decrease
the sound volume level.
OFF TIMER button
The Plasma Display can be preset to switch to stand-by after a xed
period. The setting changes to 30 minutes, 60 minutes, 90 minutes
and 0 minutes (off timer cancelled) each time the button is pressed.
When three minutes remain, “OFF TIMER 3” will ash.
The off timer is cancelled if a power interruption occurs.
Remote ID lock (see page 37)
Status button
Press the “Status” button to display the current system status.
1
Input label
2
Aspect mode (see page 18)
3
Off timer
The off timer indicator is displayed only when the off timer
has been set.
Digital Zoom (see page 26)
Press to access
Digital Zoom.
This displays an enlargement of the designated part of the
displayed image.
ACTION button
Press to make
selections.
SOUND button
(see page 25)
R button (see page 17)
Press the R button to return to previous menu screen.
Off timer 90
2
3
1
PC
4:3
30 60
0
90
POSITION buttons
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
1/2Picture
Normal
Normalise
Normal
25
0
0
0
5
Brightness
Sharpness
Picture Mode
Colour
Contrast
Tint
2/2Picture
Advanced settings
White balance
Colour Management
Normal
Off
On
Advanced settings
Normal
Normalise
0
0
0
0
0
0
2.2
Off
W/B Low B
Black extension
W/B High B
W/B Low R
AGC
Gamma
Input level
W/B High R
Normal
Normalise
Pos. /Size
0
0
0
0
V-Pos
H-Pos
V-Size
H-Size
Normal
Normalise
Pos. /Size
0
0
0
0
0
V-Pos
H-Pos
V-Size
H-Size
Clock Phase
Sound
Normal
Normalise
Normal
0
0
0
Off
Treble
0
Mid
Sound Mode
Balance
Bass
Surround
Main
Audio Out (PIP)
1/2
Signal
PC
Off
Standby save
Off
Power management
Off
Auto power off
Off
OSD Language English
(
UK
)
Component/RGB-in select
RGB
Input label
Power save
Setup
2/2Setup
Screensaver
MULTI DISPLAY Setup
Set up TIMER
PRESENT TIME Setup
INPUT MENU ENTER/+/VOL
-
/
INPUT MENU ENTER/+/VOL
-
/
1
2
16
On-Screen Menu Displays
To Pos./Size adjust menu
(see page 19)
During “RGB / PC” input signal.
During “AV(S Video)”,
“Component” and “Digital” input
signal.
To Sound adjust menu
(see page 25)
To Advanced settings
(see page 22, 23)
Press to select
“On”.
To Picture adjust menu
(see page 22)
The MENU button on the unit can also
be pressed.
Each time the MENU button is pressed,
the menu screen will switch.
[ from the unit ]
1
Press to select.
2
Press to access each adjust
screen.
1
Press to select.
Normal Viewing Picture Setup
Sound Pos. /Size
Press to enter
Advanced settings.
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
Sync
P-NR
Signal
Auto
H-Freq.
V-Freq.
kHz
Hz
33.8
60.0
[
RGB
]
Cinema reality
Off
Off
Cinema reality
P-NR
Signal
Off
Off
[
Component
]
3D Y/C Filter (NTSC)
Colour system
Signal
On
Auto
Cinema reality
Panasonic Auto (4 : 3)
Off
4 : 3
[
AV
]
P-NR
Off
Set up TIMER
POWER OFF Function
POWER OFF Time
POWER ON Time
POWER ON Function
Off
0:00
Off
0:00
PRESENT TIME 10:00
Set up TIMER
POWER OFF Function
POWER OFF Time
POWER ON Time
POWER ON Function
On
12:00
On
18:00
PRESENT TIME 10:00
Set up TIMER
POWER OFF Function
POWER OFF Time
POWER ON Time
POWER ON Function
Off
12:00
Off
18:00
PRESENT TIME 10:00
PRESENT TIME Setup
Set
PRESENT TIME
99:99
DAY
MON
PRESENT TIME MON 99:99
Cinema reality
P-NR
Signal
Off
Off
H-Freq.
V-Freq.
kHz
Hz
33.8
60.0
[
Digital
]
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit
Operating Time
Periodic Time
White bar scroll
Interval
12:00
3:00
High
Off
Off
PRESENT TIME 15:00
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit
Finish Time
Start Time
White bar scroll
Time Designation
6:15
12:30
High
Off
Off
PRESENT TIME 15:00
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit
Finish Time
Start Time
White bar scroll
Time Designation
6:15
12:30
High
Off
Off
PRESENT TIME 15:00
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit
Operating Time
Periodic Time
White bar scroll
Interval
12:00
3:00
High
Off
Off
PRESENT TIME 15:00
MULTI DISPLAY Setup
Location
MULTI DISPLAY Setup
Ratio
Off
2 × 2
A1
INPUT MENU ENTER/+/VOL
-
/
17
On-Screen Menu Displays
2
Press to access
each adjust
screen.
Press the R button to return to
previous menu screen.
Note : “Signal” setup menu displays different setting condition for each input signals. (see page 13)
To Signal screen for
Component (see page 39)
To Signal screen for RGB
(see page 39, 40)
Press the R button to return
to “Setup” menu.
Press to select POWER ON
Time / POWER OFF Time.
Press to Set up
POWER ON Time /
POWER OFF Time.
To Set up Timer selection
screen (see page 27, 28)
To PRESENT TIME Setup
(see page 27)
Press to return to next menu screen.
[ from the unit ]
To Signal screen for Digital
(see page 39, 40)
Press the R button to return
to “Setup” menu.
Press to Setup.
Press to select Start Time / Finish Time
(When Time Designation is selected).
Press to select Periodic Time / Operating Time
(When Interval is selected).
To setup Screensaver
(see page
29-31
)
To setup Multidisplay screen
(see page 33)
To Signal screen for AV
(S Video) (see page 38, 39)
Note:
Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
INPUT MENU ENTER/+/VOL
-
/
18
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema
format picture.
Press repeatedly to move through the aspect options:
Mode Picture Explanation
4 : 3
4 : 3
3
4
4:3 will display a 4:3 picture at its standard 4:3 size.
Zoom
Zoom
4
3
16
9
Zoom mode magni es the central section of the picture.
16 : 9
16 : 9
4
3
16
9
16:9 will display the picture at its maximum size but with slight
elongation.
Just
Just
4
3 9
16
Just mode will display a 4:3 picture at its maximum size but with
aspect correction applied to the center of the screen so that
elongation is only apparent at the left and right edges of the screen.
The size of the picture will depend on the original signal.
Panasonic
Auto
Panasonic Auto
416
39
The display will automatically become enlarged (depending on the
picture source), allowing you to view the picture at its maximum
size.
Notes:
Panasonic Auto mode is designed to automatically adjust the
aspect ratio to handle a mix of 16:9 and 4:3 program material.
Certain 4:3 program material, such as stock market data screens,
may occasionally cause the image size to change unexpectedly.
When viewing such programs, it is recommended that the ASPECT
be set to 4:3.
• If adjusting the Picture V-Pos/V-Size in Panasonic Auto with 16:9
mode, the adjustment is not memorized. When exiting the mode,
the screen will return to a former adjustment.
Panasonic Auto can not be selected while BNC Dual Video
Terminal Board (TY-FB9BD) is installed.
For an elongated image
Image is expanded
4
3
Changes in
accordance with
the Panasonic Auto
mode setting (see
page 39).
For a 4:3 image
[from the unit]
4 : 3 16 : 9
4 : 3 Zoom 16 : 9
Panasonic Auto Just
Note:
When selecting an input slot that attaches BNC Dual Video Terminal
Board (TY-FB9BD), Panasonic Auto cannot be selected.
Note:
Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image retention
to remain on the Plasma Display Panel.
[During MULTI PIP Operations]
• Picture and Picture, Picture in Picture :
Others : Aspect switching is not possible.
Notes:
For PC signal input, the mode switches between “4:3”, “Zoom” and “16:9” only.
For a 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p signal input, the mode
is set to “16:9” mode, and switching is not possible.
Panasonic Auto can be selected only during Video signal input.
The aspect mode is memorized separately for each input terminal.
The aspect mode changes each time the ENTER button is
pressed.
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
Normal
Normalise
Pos. /Size
0
0
0
0
V-Pos
H-Pos
V-Size
H-Size
Normal
Normalise
Pos. /Size
0
0
0
0
0
V-Pos
H-Pos
V-Size
H-Size
Clock Phase
19
Adjusting Pos. / Size
1
Press to display the Pos. /Size menu.
Press to select H-Pos / H-Size / V-Pos / V-Size /
Clock Phase.
Press to adjust Pos. / Size.
Press to exit from adjust mode.
3
2
Notes:
Adjustment details are memorized separately for different input signal formats
(Adjustments for component signals are memorized for 525 (480) / 60i · 60p,
625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250
(1080) / 50i, 750 (720) / 60p · 50p each, and RGB/PC/Digital signals are
memorized for each frequency.)
If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture
position will shift up or down. This picture position movement cannot be
controlled by the Picture Pos./Size function.
If adjusting the Picture V-Pos/V-Size in Panasonic Auto with 16:9 mode, the
adjustment is not memorized. When exiting the mode, the screen will return
to a former adjustment.
While the Pos. / Size display is active, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
Helpful Hint ( /
Normalise
Normalisation)
4
During “RGB / PC” input signal.
During “AV(S Video)”, “Component”
and “Digital” input signal.
H-Pos Adjust the horizontal position. H-Size Adjust the horizontal size.
V-Pos Adjust the vertical position. V-Size Adjust the vertical size.
Clock Phase
(RGB/PC in mode)
Eliminate the ickering and distortion.
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
AB
A
B
A
B
BA
B
A
B
A
PC1
VIDEO2
PC1
VIDEO2
VIDEO2
VIDEO1
PC1
VIDEO2
A
A
A
C
B
B
B
D
20
MULTI PIP
Press repeatedly.
Each time pressing this button main picture and sub picture will be displayed
as follows below.
Press to swap main
picture and sub picture.
[Picture out Picture]
Press to select the input mode.
Under main Picture and sub picture display,
select the picture which you would like to
change input modes.
Notes:
• The sub picture sound is heard while a sub
picture operation is underway.
• The sub picture operation automatically
returns to the main picture operation if
a sub picture operation has not been
performed for about 5 seconds or if any
of the remote control buttons is pressed
(except
button).
Press to move the sub picture.
Each time the location of the sub picture will be moved.
Notes:
• This button is effective only in the picture in picture.
• The sub picture may be hidden by the on screen display, depending on its position.
Main picture Sub picture
[Picture and Picture] [Picture in Picture]
Notes:
If “INPUT lock” in Options menu is set to other than “Off”, MULTI PIP function isn’t available.
Sound output is from the picture which is selected in Audio Out (PIP) (See page 25).
In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.
The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of
the pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals
displayed on the main picture and depending on the 2-picture display mode.
Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail.
Computer screen picture is displayed in a simpli ed format, and it may not be possible to discern details on them satisfactorily.
Following combinations of two analog signals cannot be displayed simultaneously;
Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB)
[Example]
Input modes switching is possible
Press to change input signal.
Main picture label is bright Sub picture label is bright
Picture is changed
Main picture label is changed
Sub picture label is changed
Main picture Sub picture Main picture Sub picture
Normal
Viewing
Ofrecido por www.electromanuales.com
Downloaded From TV-Manual.com Manuals
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Panasonic TH-42PH10RK Operating Instructions Manual

Category
Plasma TVs
Type
Operating Instructions Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI