Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR Owner's manual

Halsey Taylor
Brand
Halsey Taylor
Model
HRF_EBP_SBP_SEBP_ESBP_FR
Category
Sanitary ware
Type
Owner's manual
PAGE 1 97649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
Halsey Taylor Owners Manual
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
Freeze Resistant Fountains
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
HRFSBP - FR HRFSEBP - FR
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLA-
TION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE
CODES. After installation, leave these instructions inside the fountain for future reference.
This Freeze Resistant Fountain is shipped in two separate cartons. The second carton(s)
contains the Freeze Resistant Package(s) HTFRB1 that are installed on an interior
heated wall. The interior space must maintain a minimum temperature of 50° F (10° C).
Refer to the Freeze Resistant Package for the rough-in dimensions for installation.
Installer
HRFEBP - FR HRFESBP - FR
PAGE 297649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 1
HRFSBP - FR
MOUNTING BOLT AND ACCESS HOLE LAYOUT
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 1/4" DIA. (6mm) HOLES FOR MOUNTING
PLATE TO WALL
PAGE 3 97649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 2
1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom cover from fountain and save the screws.
3. Install the fountain using bolts and washers (not provided). Tighten securely.
4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide.
5. Install freeze-resistant box - see box instructions.
6. Replace bottom cover.
HRFSBP - FR
ROUGH-IN DRAWINGS
PAGE 497649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 3
HRFEBP - FR
MOUNTING BOLT AND ACCESS HOLE LAYOUT
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 1/4" DIA. (6mm) HOLES FOR MOUNTING
PLATE TO WALL
PAGE 5 97649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 4
1. Wall should already be framed for the fountain using dimensions shown in Fig. 3. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom cover from fountain and save the screws.
3. Install the fountain using bolts and washers (not provided). Tighten securely.
4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide.
5. Install freeze-resistant box - see box instructions.
6. Replace bottom cover.
HRFEBP - FR
ROUGH-IN DRAWINGS
PAGE 697649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 5
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 1/4" DIA. (6mm) HOLES FOR MOUNTING
PLATE TO WALL
HRFSEBP - FR
MOUNTING BOLT AND ACCESS HOLE LAYOUT
PAGE 7 97649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
1. Wall should already be framed for the fountains using dimensions shown in Fig. 5. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom covers from fountains and save the screws.
3. Install the fountains using bolts and washers (provided). Tighten securely.
4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.
5. Install freeze-resistant boxes - see box instructions.
6. Replace bottom covers.
FIG. 6
HRFSEBP - FR
ROUGH-IN DRAWINGS
PAGE 897649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
HRFESBP - FR
MOUNTING BOLT AND ACCESS HOLE LAYOUT
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 1/4" DIA. (6mm) HOLES FOR MOUNTING
PLATE TO WALL
FIG. 7
12 1/8"
308mm
12 1/8"
308mm
7 1/4"
184mm
7 1/4"
184mm
12"
305mm
MAX. WALL
THICKNESS
FINISHED FLOOR
26 13/16"
681mm
28 9/16"
725mm
30 1/4"
768mm
43 5/8"
1108mm
7 1/4"
184mm
BACK PANEL
3/8" DIA (20)
10mm
1 5/16"
33mm
18 3/4"
476mm
3 1/8"
80mm
3 1/8"
80mm
2 3/4"
70mm
1 5/16"
D
32 13/16"
833mm
34 9/16"
878mm
36 1/4"
921mm
7 1/4"
184mm
WALL PLATE
ASSEMBLY
B
A
C
16"
406mm
16"
406mm
5 1/4"
133mm
5 1/4"
133mm
8"
203mm
5 1/4"
133mm
5 1/4"
133mm
8"
203mm
PAGE 9 97649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
HRFESBP - FR
ROUGH-IN DRAWINGS
1. Wall should already be framed for the fountains using dimensions shown in Fig. 7. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom covers from fountains and save the screws.
3. Install the fountains using bolts and washers (provided). Tighten securely.
4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.
5. Install freeze-resistant boxes - see box instructions.
6. Replace bottom covers.
FIG. 8
33"
838mm
HRFSFR
20 3/8"
518mm
27"
686mm
HRFEFR
ADA
REQUIREMENT
6 1/2"
165mm
38 1/2"
978mm
6 5/8"
168mm
12 1/8"
318mm
3 13/16"
97mm
FINISHED FLOOR
12 1/4"
311mm
HRFSFR
18"
457mm
HRFEFR
5/8"
16mm
12"
305mm
MAX. WALL
THICKNESS
2 5/8"
67mm
3 5/8"
92mm
13 1/8"
333mm
HRFEFR
14 3/16"
360mm
HRFEFR
17 11/16"
449mm
HRFEFR
19 1/8"
486mm
HRFSFR
20 3/16"
513mm
HRFSFR
23 11/16"
602mm
HRFSFR
28 9/16"
725mm
HRFEFR
34 9/16"
878mm
HRFSFR
PAGE 1097649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 12
FIG. 13
FIG. 9
FIG.
10
See Fig. 11
See Fig. 7
FIG.
11
CABLE SHEATH ADJUSTMENT
To Increase Free Play
To Reduce Free Play
PAGE 11 97649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the interior
heated area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed mounted. If recess
mounted the surface of the cover must be flush with the interior wall surface. The package is furnished with screws for
mounting the cover to the box. If the box is recess mounted, do not fasten the top and bottom of the cover to the box. Use
the holes on the front only.
1. Assemble the operating cable to the fountain bracket. (Fountain should be mounted to exterior wall) Create a loop in
the cable and thread the free end of the cable through the wall into the freeze resistant box. The adjustment nuts should
be in the middle of threaded area on the operating cable. See Figure 13
2. Connect free end of operating cable to the valve-operating bracket. The end of the cables must be recessed into the
indents on the pivot brackets.
3. Remove cable free play by adjusting the jam nuts on the ends of the operating cable. See Figure 10
4. Connect water line from fountain bubbler into freeze resistant box. The connection to the box uses a quick connect
water fitting. Position the water line, in the fountain, to drain back into interior mounted box. Any water left standing, in
the exterior line, can freeze.
To insert tubing, push tube straight into fitting until it reaches a positive stop. To remove tubing from the fittings, relieve
water pressure, push in on dark gray collar while pulling out on the tubing. See Figure 15
5. Connect drain and water supply lines to the freeze resistant fountain. Refer to Figure 1 for component positions. Inline
strainer must be used on the inlet water line.
Start-up
1. Turn on building water supply and check all connections for leaks. Repair as required.
2. Stream height is factory set at 35 PSI. If stream height needs to be changed adjust the regulator in the freeze resistant
package. Clockwise adjustment raises stream height, counter clockwise adjustment will lower stream.
3. Adjust operating cable as required. Cable system should have a minimal amount of free play to allow for proper valve
operation. If the system is too tight the valve will stay in the on position creating constant water flow. Too much free
play will result in non-operation of the valve with the push-buttons.
4. Note: Water from the drain back tube in the freeze resistant package, will continue to run while the valve is actuated.
5. After cable system is adjusted properly stuff flexible insulation into any openings between the outside wall and the
interior box.
6. Recheck all connections. If all connections are leak free replace cover(s) on the freeze resistant box(es) and fountain(s).
FIG. 14
NOTE: WATER FLOW DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 15
OPERATION OF QUICK CONNECT FITTINGS
PAGE 1297649C (Rev. K - 4/07)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
56092C
112627543890
15009C
27057C
27945C
27946C
40045C
40206000
98118C
45662C
45663C
50198C
51667C
55919C
70425C
28465C
28466C
55000661
55000665
23187C
23189C
27043C
27261C
75672C
72000833
100322740560
28158C
28170C
28159C
28178C
56280C
PART NO.
ITEM NO.
PARTS LIST
POLY TUBING (CUT TO LENGTH)
SCREW - #10 - 24 X .50 PHTC
NIPPLE ASSY
BRACKET-REGULATOR MOUNTING
BRACKET-BASIN
BRACKET-BASIN PIVOT
HEX NUT 1-5/16
RETAINER
BUBBLER ASSEMBLY
PUSH BUTTON
SLEEVE-PUSH BUTTON GUIDE
SNAP BUSHING
BUMPER-REG. VALVE ASSY
PUSH BUTTON (EXTENSION)
PIVOT ROD
FOUNTAIN ARM - SHORT
FOUNTAIN ARM - LONG
BOTTOM COVER PLATE - SHORT
BOTTOM COVER PLATE - LONG
BACK PANEL - HRFSBP
BACK PANEL - HRFEBP
BACK PANEL - HRFSEBP
BACK PANEL - HRFESBP
CAP SCREW
WASTE ARM ASSY
WASHER
WALL PLATE ASSEMBLY - HRFSBP
WALL PLATE ASSEMBLY - HRFEBP
WALL PLATE ASSEMBLY - HRFSEBP
WALL PLATE ASSEMBLY - HRFESBP
EDGE TRIM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
DESCRIPTION
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
12
4
11, 19
10
14
8
15
13
5
7
6
12
16
FIG. 18
FIG. 17
FIG. 16
9
21
3
SEE FIG. 18
22, 18
20
2, 17
SEE FIG. 17
1
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
23
23
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR Owner's manual

Halsey Taylor
Brand
Halsey Taylor
Model
HRF_EBP_SBP_SEBP_ESBP_FR
Category
Sanitary ware
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents