Craftsman 315.114853 User manual
- Category
- Power drills
- Type
- User manual
This manual is also suitable for
PERATOR'S MAN AL
®
1/2 in. 19.2 VOLT CORDLESS DRILL-DRIVER
VARIABLE SPEED/REVERSIBLE
Model Nos.
315.114852
315.114853
A
WARNING: To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
product.
Craftsman Consumer Helpline: 1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
983000-848
12123-08 (REV:07)
Save this manual for future reference
[] Warranty .......................................................................................................................................................................... 2
[] Introduction ..................................................................................................................................................................... 2
[] General Safety Rules .................................................................................................................................................... 3-4
[] Specific Safety Rules....................................................................................................................................................... 4
[] Safety Rules for Charger ................................................................................................................................................. 5
[] Symbols ........................................................................................................................................................................ 6-7
[] Features ........................................................................................................................................................................ 8-9
[] Assembly ......................................................................................................................................................................... 9
[] Operation .................................................................................................................................................................. 10-15
[] Maintenance ............................................................................................................................................................. 16-17
[] Exploded View and Parts List ........................................................................................................................................ 18
[] Parts Ordering/Service ..................................................................................................................................... Back Page
ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL
If this Craftsman tool fails to give complete satisfaction within one year from date of purchase, RETURN iT TO ANY
SEARS STORE OR PARTS AND REPAIR CENTER OR OTHER CRAFTSMAN OUTLET iN THE UNITED STATES FOR
FREE REPAIR (or rep(acement if repair proves impossib(e).
If this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of
purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, iL 60179
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
A
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
_ WARNING!READANDUNDERSTAND ALL
INSTRUCTIONS. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious personal injury.
SAVE THESE iNSTRUCTiONS
WORK AREA
[] Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
[] Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
[] Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
ELECTRICALSAFETY
[] A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery.
[] Use battery operated tool only with specifically des-
ignated battery pack. Use of any other batteries may
create a risk of fire.
[] Use battery only with charger listed.
MODEL BATTERY PACK CHARGER
(M-ion)
315.114852
315.114853
315.113740
(130285003,
130285006)
315.113710
(130156001)
BATTERY PACK
(NFCd)
130239003,
130279003,
130279005
(Item No. 911375)
PERSONAL SAFETY
(Multi-Chemistry)
315.259260
(140351001)
315. 259260
(140351001)
1425301 (911041)
315.115730
(140301003)
315.115720
(140301001)
[] Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inatten-
tion while operating power tools may result in serious
personal injury.
[] Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
[] Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or insert-
ingthe battery pack into a tool with the switch on
invites accidents.
[] Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
[] Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the tool in unexpected situations.
[] Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
[] Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
[] Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
TOOL USE AND CARE
[] Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
[] Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it isdesigned.
[] Do not use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is dan-
gerous and must be repaired.
[] Disconnect battery pack from tool or place the
switch in the locked or off position before making
any adjustments, changing accessories, or storing
the tool. Such preventive safety measures reduce the
risk of starting the tool accidentally.
[] Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
[] When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
[] Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cut-
ting edges are less likely to bind and are easier to
control.
[] Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that
may affect the tool's operation. If damaged, have
the tool serviced before using. Many accidents are
caused by poorly maintained tools.
[] Use only accessories that are recommended by the SERVICE
manufacturer for your model. Accessories that may
be suitable for one tool may create a risk of injury when
used on another tool.
Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool.
Following this rule will reduce the risk of loss of control
and deterioration of the enclosure plastic.
[]
[]
[]
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel may result in a risk of injury.
When servicing a tool, use only identical replace-
merit parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
[] Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring. Contact with a "live" wire will
also make exposed metal parts of the tool "live" and
shock the operator.
[] Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
[] Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses.
They are NOT safety glasses. Following this rule will
reduce the risk of eye injury.
[] Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
[] Protect your hearing. Wear hearing protection
during extended periods of operation. Following this
rule will reduce the risk of serious personal injury.
[] Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
[] Do not place battery tools or their batteries near
fire or heat. This will reduce the risk of explosion and
possibly injury.
[] Do not crush, drop or damage battery pack. Do
not use a battery pack or charger that has been
dropped or received a sharp blow. A damaged
battery is subject to explosion. Properly dispose of a
dropped or damaged battery immediately.
[] Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery
can propel debris and chemicals. If exposed, flush with
water immediately.
[] Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
[] For best results, your battery tool should be
charged in a location where the temperature is
more than 50°F but less than 100°F. To reduce the
risk of serious personal injury, do not store outside or in
vehicles.
[] Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
[] If the power supply cord is damaged, it must be
replaced only by the manufacturer or by an authorized
service center to avoid risk.
A
WARNING! READ AND UNDERSTAND ALL
INSTRUCTIONS. Failure to follow all instructions
listed below, may result in electric shock, fire and/or
serious personal injury.
[] Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, battery, and product using battery to prevent
misuse of the products and possible injury or damage.
CAUTION: To reduce the risk of electric shock
or damage to the charger and battery, charge
only nickel-cadmium rechargeable batteries as
specifically designated on your charger. Other
types of batteries may burst, causing personal
injury or damage.
[] Do not use charger outdoors or expose to wet or
damp conditions. Water entering charger will increase
the risk of electric shock.
[] Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
[] Do not abuse cord or charger. Never use the cord to
carry the charger. Do not pull the charger cord rather
than the plug when disconnecting from receptacle.
Damage to the cord or charger could occur and create
an electric shock hazard. Replace damaged cords
immediately.
[] Make sure cord is located so that it will not
be stepped on, tripped over, come in contact
with sharp edges or moving parts or otherwise
subjected to damage or stress. This will reduce the
risk of accidental falls, which could cause injury, and
damage to the cord, which could result in electric
shock.
[] Keep cord and charger from heat to prevent
damage to housing or internal parts.
[] Do not let gasoline, oils, petroleum-based products,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
[] An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere rating
of charger as specified below:
Cord Length (Feet) 25' 50' 100'
Cord Size (AWG) 16 16 16
NOTE: AWG = American Wire Gauge
[] Do not operate charger with a damaged cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
[] Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way. Take it to an authorized serviceman for electrical
check to determine if the charger is in good working
order.
[] Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
[] Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of
electric shock.
[] Disconnect charger from the power supply when
not in use. This will reduce the risk of electric shock
or damage to the charger if metal items should fall into
the opening. It also will help prevent damage to the
charger during a power surge.
[] Risk of electric shock. Do not touch uninsulated
portion of output connector or uninsulated battery
terminal.
[] Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also to prevent misuse of the product and
possible injury.
=
2.
3.
I PC NT SAFETY INSTRUCTION
SAVE THE E IN }TR CTIO
This manual contains important safety and operating instructions for battery charger 1425301 (item No. 911041).
Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and
product using battery.
CAUTION: To reduce the risk of injury, charge only nickel-cadmium rechargeable batteries. Other types of batteries
may burst, causing personal injury or damage.
Someofthefollowingsymbolsmaybeusedonthisproduct.Pleasestudythemandlearntheirmeaning.Proper
interpretationofthesesymbolswillallowyoutooperatetheproductbetterandsafer.
SYMBOL NAME DESIGNATION/EXPLANATION
V
A
mz
W
min
n o
[]
.../min
@
O
,A
@
@
@
@
Volts
Amperes
Hertz
Watt
Minutes
Alternating Current
Direct Current
No Load Speed
Class II Construction
Per Minute
Wet Conditions Alert
Read The Operator's Manual
Eye Protection
Safety Alert
No Hands Symbol
No Hands Symbol
No Hands Symbol
No Hands Symbol
Hot Surface
Voltage
Current
Frequency (cycles per second)
Power
Time
Type of current
Type or a characteristic of current
Rotational speed, at no load
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator's manual before using this product.
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
To reduce the risk of injury or damage, avoid contact with any hot
surface.
Thefollowingsignalwordsandmeaningsareintendedtoexplainthelevelsofriskassociatedwiththisproduct.
SYMBOL SIGNAL MEANING
_lk Indicates an imminently hazardous situation, which, if not avoided, will result
DANGER:
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result
WARNING: in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in
CAUTION:
minor or moderate injury.
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
Servicing requires extreme care and knowledge and
should be performed only by a qualified service techni-
cian. For service we suggest you return the product to
your nearest SEARS PARTS AND REPAIR SERVICE
CENTER for repair. When servicing, use only identical
replacement parts.
_ WARNING: To avoid serious personal injury, do
not attempt to use this product until you read thor-
oughly and understand completely the operator's
manual. If you do not understand the warnings and
instructions in the operator's manual, do not use this
product. Call the Craftsman Consumer Helpline at
1-800-932-3188 for assistance.
_ WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and, when needed, a full face shield. We recommend
Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
PRODUCT SPECIFiCATiONS
Chuck .......................................................... 1/2 in. Keyless
Motor ............................................................... 19.2 Volt DC
Switch .............................. VSR (Variable Speed Reversible)
Gear Train .............................................................. 2 Speed
No Load Speed ....................... 0-400/0-1,400 r/min. (RPM)
Clutch ................................................................ 24 Position
Torque ................................................................... 410 in.lb.
Charger Input .................................... 120 V,AC only, 60 Hz
Charge Rate ............................................................. 1 hour
LEVEL
TORQUE
ADJUSTMENTRING
TWO-SPEED
GEARTRAIN(HI-LO)
\
KEYLESS
CHUCK
REARViEW
LEVEL
SWITCH
TRIGGER
SCREWDRIVER
BiTS
DiRECTiONOF
ROTATIONSELECTOR
(FORWARD/REVERSE/
CENTERLOCK)
BiT
STORAGE
BATTERYPACK
SHOWNIN
CHARGER
CHARGER
BATTERY
PACK
4-1/2 in.
i AUTION
Do not use any DC to AC power
invertera. Charger will be Damaged!
Fig. 1
KNOWYOUR DRILL DRIVER
See Figure 1.
The safe use of this product requires an understanding of
the information on the product and in this operator's manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all op-
erating features and safety rules.
BIT STORAGE
Bits provided with the drill can be placed in the storage
area, located on the base of the drill
CHARGER
The charger has a key-hole hanging feature for conve-
nient, space-saving storage. Screws should be installed
so that the center distance is 4-1/2 in.
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK}
Your drill has a direction of rotation (forward/reverse/cen-
ter lock) selector located above the switch trigger for
changing the direction of bit rotation. Setting the switch
trigger in the OFF (center lock) position helps reduce the
possibility of accidental starting when not in use.
KEYLESS CHUCK
The keyless chuck allows you to hand-tighten or release
the drill bit in the chuck jaws.
LEVELS
Levels are located on the top and end of the motor hous-
ing to help keep the drill bit level dudng use.
TORQUE ADJUSTMENT RING
Your drill has a 24-position clutch. The torque adjustment
ring can be turned to select the right amount of torque for
your application.
TWO SPEED GEAR TRAIN
The two-speed gear train is designed for drilling or driving
at LO (1) or HI (2) speeds. A slide switch is located on top
of your drill for selecting either LO (1) or Hi (2) speed.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with
decreased trigger pressure.
UNPACKING
This product has been shipped completely assembled.
[] Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing
list are included.
[] Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
[] Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
[] If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
PACKING LIST
1/2 in. Drill-Driver
Charger
Battery Pack (2)
Double-ended Bit (2)
Bag
Operator's Manual
A
A
WARNING: If any parts are damaged or missing
do not operate this product until the parts are re-
placed. Failure to heed this warning could result in
serious personal injury.
WARNING: Do not attempt to modify this product
or create accessories not recommended for use with
this product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING: To prevent accidental starting that
could cause serious personal injury, always remove
the battery pack from the product when assembling
parts.
A
A
A
WARNING: Do not allow familiarity with products to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
WARNING: Always wear safety goggles or safety
glasses with side shields when operating products.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
WARNING: Do not use any attachments or acces-
sories not recommended by the manufacturer of this
product. The use of attachments or accessories not
recommended can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
[] Drilling in wood
[] Drilling in ceramics, plastics, fiberglass, and laminates
[] Drilling in metals
[] Mixing paint
This product will accept DieHard_ 19.2 V lithium-ion bat-
tery packs and Craftsman 19.2 V nickel-cadmium battery
packs.
For complete charging instructions, refer to the Opera-
tor's Manual for the battery packs and chargers listed in
the General Safety Rules.
10
BATTERY PROTECTION FEATURES
DieHardo 19.2 V lithium-ion battery packs are designed
with features that protect the lithium-ion cells and
maximize battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
LED FUNCTIONS OF CHARGER
CAUTION: If at any point during the charging
process none of the LEDs are lit, remove the bat-
tery pack from the charger to avoid damaging the
product. DO NOT insert another battery. Return the
charger and battery to your nearest Sears or other
qualified service center for service or replacement.
LED WILL BE ON TO INDICATE STATUS OF
CHARGER AND BATTERY PACK:
[] Red LED on = Fast charging mode.
[] Green LED on = Fully charged and in maintenance
charge mode.
[] Green LED on = When battery pack is inserted into
charger, indicates hot battery pack or that battery pack
is out of normal temperature range.
[] Yellow and Green LEDs on = Deeply discharged or
defective battery pack.
[] No LED on = Defective charger or battery pack.
CHARGING THE BATTERY PACK
The battery pack for this product has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until the green LED on the front of the
charger comes on.
NOTE: Batteries will not reach full charge the first time they
are charged. Allow several cycles (operation followed by
recharging) for them to become fully charged.
CHARGING A COOL BATTERY PACK
If battery pack is below normal temperature range, the green
LED on charger will come on. Allow battery pack to reach
normal temperature, then the red LED will come on.
NOTE: If the charger does not charge the battery pack under
normal circumstances, return both the battery pack and char-
ger to your nearest Sears or other qualified service center for
electrical check.
[] Charge the battery pack only with the charger provided.
[] Make sure the power supply is normal household
voltage, 120 volts, AC only, 60 Hz.
[] Connect the charger to the power supply.
[] Place the battery pack in the charger aligning raised rib
on the battery pack with the groove in the charger. See
Figure 2.
[] Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts inthe
charger.
[] Normally the red LED on charger will come on. This
indicates the charger is in fast charging mode.
[] Red LED should remain on for approximately 1 hour
then the green LED will come on. Green LED on
indicates battery pack is fully charged and charger is
in maintenance charge mode.
NOTE: The green LED will remain on until the battery
pack is removed from the charger or charger is
disconnected from the power supply.
[] If both yellow and green LEDs come on, this indicates
a deeply discharged or defective battery pack. Allow
the battery pack to remain in the charger for 15 to 30
minutes. When the battery pack reaches normal
voltage range, the red LED should come on. If the red
LED does not come on after 30 minutes, this may
indicate a defective battery pack that should be
replaced.
[] After normal usage, a minimum of 1 hour of charging
time is required to fully recharge battery pack.
[] The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
[] Do not place the charger and battery pack in an area
of extreme heat or cold. They will work best at normal
room temperature.
NOTE: The charger and battery pack should be placed
in a location where the temperature is more than 50°F
but less than 100°R
[] When batteries become fully charged, unplug the
charger from power supply and remove the battery
pack.
11
CHARGING A HOT BATTERY PACK
When using the product continuously, the batteries in the
battery pack will become hot. You should let a hot bat-
tery pack cool down for approximately 30 minutes before
attempting to recharge. When the battery pack becomes
discharged and is hot, this will cause the green LED to
come on instead of the red LED. After 30 minutes, reinsert
the battery pack in the charger. If the green LED continues
to remain on, return battery pack to your nearest Sears or
other qualified service center for checking or replacing.
NOTE: This situation only occurs when continuous use of
the product causes the batteries to become hot. It does
not occur under normal circumstances. Refer to CHARG-
ING A COOL BATTERY PACK for normal recharging
of batteries. If the charger does not charge your battery
pack under normal circumstances, return both the battery
pack and charger to your nearest Sears or other qualified
service center for electrical check.
BATTERYPACK
SHOWNIN CHARGER
CHARGER
REDLED
TO iNSTALL BATTERY PACK
See Figure 3.
[] Lock switch trigger on the drill by placing the direction
of rotation selector in center position.
[] Place battery pack in the drill. Align raised rib on bat-
tery pack with groove inside drill.
[] Make sure the latches on each side of your battery
pack snap in place and battery pack is secured in drill
before beginning operation.
CAUTION: When placing battery pack in the drill, be
sure raised rib on battery pack aligns with groove in-
side drill and latches snap into place properly. Improper
assembly of battery pack can cause damage to internal
components.
A
WARNING: Always remove battery pack from your
tool when you are assembling parts, making adjust-
ments, cleaning, or when not in use. Removing bat-
tery pack will prevent accidental starting that could
cause serious personal injury.
TO REMOVE BATTERY PACK
See Figure 3.
[] Lock switch trigger on the drill by placing the direction of
rotation selector in center position.
[] Locate latches on side of battery pack and depress to
release battery pack from the drill.
[] Remove battery pack from the drill.
GREENLED
[
YELLOW
LED Fig. 2
CAUTION
Do not use any DC to AC power
inverters, Charger will be Damaged!
i
BATTERY
PACK
LATCHES
12
DEPRESSLATCHESTO
RELEASEBATTERYPACK
Fig. 3
A
WARNING: Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
DiRECTiONOFROTATIONSELECTOR
(FORWARD/REVERSE/CENTERLOCK)
REVERSE
VARIABLESPEED
SWITCHTRIGGER
f
FORWARD
Fig. 4
SWITCH TRIGGER
See Figure 4.
To turn the drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with
decreased trigger pressure.
NOTE: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a
normal part of the switch function.
DiRECTiON OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK}
See Figure 4.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the
drill held in normal operating position, the direction of
rotation selector should be positioned to the left of the
switch trigger for drilling. The drilling direction is reversed
when the selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when not
in use.
CAUTION: To prevent gear damage, always allow
the chuck to come to a complete stop before
changing the direction of rotation.
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.
NOTE: The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the drill to become overheated. If this occurs, cool
the drill by running it without a load and at full speed.
KEYLESS CHUCK
See Figure 5.
The drill has a keyless chuck to tighten or release drill bits
in the chuck jaws. Grasp and hold the collar of the chuck
with one hand. Rotate the chuck body with your other
hand. The arrows on the chuck indicate which direction
to rotate the chuck body in order to LOCK (tighten) or
UNLOCK (release) the drill bit.
A
WARNING: Do not hold the chuck body with one
hand and use the power of the drill to tighten the
chuck jaws on the drill bit. The chuck body could slip
in your hand, or your hand could slip and come in
contact with the rotating drill bit. This could cause an
accident resulting in serious personal injury.
KEYLESS
CHUCK CHUCK
UNLOCK COLLAR
DRILLBiT (RELEASE)
CHUCK
JAWS
LOCK
(TIGHTEN)
CHUCK
BODY
Fig. 5
13
TWO=SPEED GEAR TRAIN
See Figure 6.
The drill has a two-speed gear train designed for drilling or
driving at LO (1) or HI (2) speeds. A slide switch is located
on top of the drill to select either LO (1) or HI (2) speed.
When using drill in the LO (1) speed range, speed will
decrease and unit will have more power and torque. When
using drill in the Hi (2) speed range, speed will increase
and unit will have less power and torque. Use LO (1)
speed for high power and torque applications and Hi (2}
speed for fast drilling or driving applications.
TWOSPEED
GEARTRAIN(Hi-LO)
SPEED
LO
SPEED
Fig. 6
ADJUSTABLE TORQUE CLUTCH
This product is equipped with an adjustable torque
clutch for driving different types of screws into different
materials. The proper setting depends on the type of ma-
terial and the size of screw you are using.
ADJUSTING TORQUE
See Figure 7.
[] There are twenty-four torque indicator settings located
on the front of the drill.
[] Rotate the adjusting ring to the desired setting.
• 1-4
• 5-8
• 9-12
• 13-16
• 17 -23
For driving small screws
For driving screws into soft material
For driving screws into soft and hard
materials
For driving screws into hard wood
For driving large screws
For heavy drilling
TODECREASE ADJUSTING
TORQUE RiNG
V
TOINCREASE
TORQUE
Fig. 7
14
INSTALLINGBITS
See Figure 8.
[] Lock the switch trigger by placing the direction of
rotation selector in the center position.
[] Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend to
use. Also, raise the front of the drill slightly to keep the
bit from falling out of the chuck jaws.
[] Insert the drill bit.
,_ WARNING: Make sure to insertthe drill bit straight
into the chuck jaws. Do not insert the drill bit into
the chuck jaws at an angle then tighten, as shown in
figure 9. This could cause the drill bit to be thrown
from the drill, resulting in possible serious personal
injury or damage to the chuck.
[] Tighten the chuck jaws securely on the bit.
NOTE: Rotate the chuck body in the direction of the
arrow marked LOCK to close the chuck jaws. Do not
use a wrench to tighten or loosen the chuck jaws.
DRILLB(T
CHUCK
UNLOCK COLLAR
(RELEASE)
CHUCK
JAWS
LOCK
(TIGHTEN)
CHUCK
BODY
RIGHT
REMOVING BITS
See Figure 8.
[] Lock the switch trigger by placing the direction of
rotation selector in the center position.
[] Open the chuck jaws.
NOTE: Rotate the chuck body in the direction of the
arrow marked UNLOCK to open the chuck jaws. Do
not use a wrench to tighten or loosen the chuck jaws.
[] Remove the drill bit.
Fig. 9
BIT STORAGE
See Figure 10.
When not in use, bits provided with the drill can be placed
in the storage area located on the base of the drill.
SCREWDRIVER
BIT
Fig. 8
BITSTORAGE AREA
Fig.I0
15
DRILLING
See Figures 11 - 12..
Levels are located on the top and end of the motor
housing to help keep the drill bit level during use.
[] Check the direction of rotation selector for the correct
setting (forward or reverse).
[] Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
[] Hold the drill firmly and place the bit at the point to be
drilled.
[] Depress the switch trigger to start the drill.
[] Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
A
WARNING: Be prepared for binding at bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
[] When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off-center as the hole
is started.
[] When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life of
the bit and increase the drilling action.
[] If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
NOTE: This drill has an electric brake. When the switch
trigger is released, the chuck stops turning. When the
brake is functioning properly, sparks will be visible through
the vent slots on the housing. This is normal and is the
action of the brake.
WOOD DRILLING
For maximum performance, use high speed steel bits for
wood drilling.
[] Select normal drilling mode.
[] Begin drilling at a very low speed to prevent the bit
from slipping off the starting point. Increase the speed
as the drill bit bites into the material.
[] When drilling through holes, place a block of wood
behind the workpiece to prevent ragged or splintered
edges on the back side of the hole.
Fig. 11
LEVEL
Fig. 12
16
METAL DR(LLING
For maximum performance, use high speed steel bits for
metal or steel drilling.
== Select normal drilling mode.
== Begin drilling at a very low speed to prevent the bit from
slipping off the starting point.
== Maintain a speed and pressure which allows cutting
without overheating the bit. Applying too much pressure
will:
• Overheat the drill;
• Wear the bearings;
• Bend or burn bits; and
• Produce off-center or irregular-shaped holes.
When drilling large holes in metal, start with a small bit,
then finish with a larger bit. Also, lubricate the bit with oil
to improve drilling action and increase bit life.
A
A
WARNING: When servicing, use only identical
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
WARNING: Always wear safety goggles or safety
glasses with side shields when using compressed air
to clean products. If the operation is dusty, also wear
a dust mask.
WARNING: To avoid serious personal injury, always
remove the battery pack from the product when
cleaning or performing any maintenance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
_ WARNING: Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may result
in serious personal injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a Sears Service Center.
BATTERIES
This product will accept DieHard<_19.2 V lithium-ion bat-
tery packs and Craftsman 19.2 V nickel-cadmium battery
packs.
The batteries for this product have been designed to provide
maximum trouble-free life. However, like all batteries, they will
eventually wear out. Do not disassemble battery pack and
attempt to replace the batteries. Handling of these batteries,
especially when wearing rings and jewelry, could result in a
serious burn.
To obtain the longest possible battery life, we suggest the
following:
For lithium=ion batteries:
== Remove the battery pack from the charger once it is
fully charged and ready for use.
For battery pack storage longer than 30 days:
== Store the battery pack where the temperature is below
80°F and away from moisture.
• Store battery packs in a 30%-50% charged condition.
• Every six months of storage, charge the pack as normal.
For nickel=cadmium batteries:
• Remove the battery pack from the charger once it is
fully charged and ready for use.
For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below
80°R
• Store battery packs in a "discharged" condition.
BATTERY PACK REMOVAL AND PREPARATION
FOR RECYCLING
To preserve natural resources, please
recycle or dispose of batteries properly.
This product uses nickel-cadmium and
lithium-ion batteries. Local, state or
federal laws may prohibit disposal of
batteries in ordinary trash.
Consult your local waste authority for
information regarding available recycling
and/or disposal options.
A
WARNING: Upon removal, cover the battery pack's
terminals with heavy-duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or re-
move any of its components. Lithium-ion and nickel-
cadmium batteries must be recycled or disposed of
properly. Also, never touch both terminals with metal
objects and/or body parts as short circuit may result.
Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
17
CHUCKREMOVAL
See Figures 13- 15.
The chuck may be removed and replaced by a new one.
[] Lock the switch trigger by placing the direction of rota-
tion selector in center position.
[] Insert a 5/16 in. or larger hex key intothe chuck of the
drill and tighten the chuck jaws securely.
[] Tap the hex key sharply with a mallet in a clockwise di-
rection. This will loosen the screw in the chuck for easy
removal.
MALLET
MALLET
CHUCKJAWS
\
[]
KEYLESS
HEXKEY CHUCK
Fig. 13
Open the chuck jaws and remove the hex key. Using a
screwdriver, remove the chuck screw by turning it in a
clockwise direction.
NOTE: The chuck screw has left hand threads.
HEXKEY
Fig. 15
TO RETIGHTEN A LOOSE CHUCK
The chuck may become loose on the spindle and develop
a wobble. Also, the chuck screw may become loose,
causing the chuck jaws to bind and prevent them from
closing. To tighten:
[] Lock the switch trigger by placing the direction of rota-
tion selector in the center position.
[] Open the chuck jaws.
[] Insert the hex key into the chuck and tighten the chuck
jaws securely. Tap the hex key sharply with a mallet in
a clockwise direction. This will tighten the chuck on the
spindle.
[] Open the chuck jaws and remove the hex key.
[] Tighten the chuck screw.
SCREWDRIVER
[]
Fig. 14
Insert the hex key into the chuck and tighten the chuck
jaws securely. Tap sharply with a mallet in a counter-
clockwise direction. This will loosen the chuck on the
spindle. It can now be unscrewed by hand.
18
CRAFTSMAN 1/2 in., 19.2 VOLT CORDLESS DRILL-DRIVER
MODEL NOS. 315.114852 and 315.114853
The model number will be found on a plate attached to the motor housing. Always mention the model |
number in all correspondence regarding your DRILUDRiVER or when ordering repair parts,
J
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
4
2
3
PARTS LIST
Key Part
No. Number
1 6613402
2 6903323
3 1323903,130279003
or130279005
4 1425301
5 940237103
6 940203007
7 940045102
8 940203007
9 300912203
10 300912279
11 900211023
12 9021107
983000848
Description Qty.
Screw (Special) ................................................................................................ 1
Chuck ............................................................................................................ 1
*Battery Pack (Item No. 9_11375) ..................................................................... 1
*Charger (Item No. 9_11041) ............................................................................. 1
Data Plate (114852) (Not shown) ..................................................................... 1
Logo Plate (114852) (Not shown) .................................................................... 1
Data Plate (114853) (Not shown) ..................................................................... 1
Logo Plate (114853) (Not shown) .................................................................... 1
Carrying Case (11548 Combo) (Not shown) .................................................... 1
Carrying Case (11590 Combo) (Not shown) .................................................... 1
Bag (11561 Combo) (Not shown) .................................................................... 1
Bag (11588 Combo) (Not shown) .................................................................... 1
Operator's Manual
* Can Be Purchased At Most Sears Stores/Sears.corn/Parts and Service
qN
Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME ® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
www.sears.com
1-800-469-4663 (Canada)
www.sears.ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR ®
(1-888-784-6427)
Au Canada pour service en fran£ais:
1-800-LE-FOYER M°
(1-800-533-6937)
www.sears.ca
TM
® Registered Trademark / Trademark / SMService Mark of Sears Brands, LLC
TM
® Marca Registrada / Marca de Fabrica / SMMarca de Servicio de Sears Brands, LLC
MD
MCMarque de commerce / Marque depos6e de Sears Brands, LLC © Sears Brands, LLC
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Craftsman 315.114853 User manual
- Category
- Power drills
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Craftsman 973271970 Owner's manual
-
-
-
-
-
-
-
-
-
