MB QUART Out of stockMBQJ-STG6-1 User manual

Page 1 of 33

Assembly Instructions

Model:

Jeep JL (Wrangler) & JT (Gladiator)

Description:

Front, Rear, Top Dash Speaker Install

Part Number:

MBQJ-STG6-1

Assembly Time:

120 Min (2-Hours)

Parts List

No. Component Name Qty

1 6.5in Midbass Speaker Kit (JW1-116E) 2

2 6.5in Lower Dash Speaker Enclosure (JE1-116) 2

3 3.5in Coaxial Speakers (JC1-108) 2

4 6x9in Rear Coaxial Kit (JC1-169SB) 2

5 Speaker Harness 2

1 Bojo or Panel Tool

2 Philips Screwdriver

3 8, 10, 13mm Socket

4 Rachet

Parts List

Tools Required

Before you beign, read thought these instructions and check that

all parts are present. Please note that MB Quart cannot assume any

responsibility for damage resulting from incorrect installation.

Page 2 of 33

Dash Disassembly

● Unclip and remove panel below

the steering column

● Remove (2) Phillips screws

● Unclip, unplug, and remove the

climate control panel

Page 3 of 33

Dash Disassembly

● Remove (2) Phillips screws

securing the radio trim panel,

then unclip and remove

● Remove (1) Phillips screw

securing the front dash pad,

carefully unclip and remove by

pulling forward toward the front

seats

Page 4 of 33

Dash Disassembly

● Carefully unclip the instrument

panel shroud along the bottom

and remove

● Unclip the lower steering column

shroud and move toward steering

wheel

Page 5 of 33

Dash Disassembly

● Unclip and remove the panel on

the side of the dash

● Remove (5) Phillips screws that

are exposed

● Unclip kick panel cover

● Remove (1) Phillips screw from

lower left dash

● Remove (2) Phillips screws near

steering column

● Remove (2) Phillips screws on

the top of the left dash then unclip

and disconnect wiring on back of

light switch to remove panel from

vehicle

Page 6 of 33

Dash Disassembly

Page 7 of 33

Lower Speaker Removal

● Remove (4) 10mm bolts below

steering column. (one is hidden

behind the cross brace behind the

left down support)

● Remove (1) 8mm bolt below the

speaker and this will free the

lower support brace to aid in the

removal of the speaker enclosure

● Remove (3) Phillips screws

securing the speaker enclosure

Page 8 of 33

Lower Speaker Removal

● Disconnect harness from the

enclosure and module mounted

on the back side, then remove

from vehicle

● Remove the module from the

OEM enclosure

Page 9 of 33

Dash Disassembly

● Install the module on the new

enclosure using the OEM

hardware

● On passenger side remove

(4) Phillips screws

Dash Disassembly

● Unclip and remove the panel on

the side of the dash

● Using a panel tool carefully

remove the grab handle cover

(starting on the left)

Page 10 of 33

Dash Disassembly

● Remove (2) 10mm bolts securing

the grab handle and set handle

aside

● Unclip the airbag cover panel

● Remove (2) Phillips screws that

have been exposed

Page 11 of 33

Dash Disassembly

● Remove glove box by opening

and lifting the upper tab and

removing the latch on the left side

● Remove three Phillips screws

that have been exposed

● Looking in the glovebox cavity

up high, remove two 13mm

bolts securing the back of the

passenger side airbag

Page 12 of 33

Dash Disassembly

● Carefully unclip the air bag. (this

does NOT need to be removed

from the vehicle)

● Lifting the airbag slightly will

expose (5) Phillips screws that

need to be removed

Page 13 of 33

Dash Disassembly

● Remove (3) Phillips screws

holding the passenger speaker

enclosure, then disconnect wires

and remove from vehicle

Page 14 of 33

Upper Speaker Replacement

● If you are replacing the upper

speakers as well, complete

Steps 34 and 35 for driver and

passenger side.

Unclip and remove dash grill

● Remove (2) Phillips screws,

disconnect wiring and remove

speaker from vehicle

● Install new speaker enclosure and

secure with (3) Phillips screws

Page 15 of 33

Upper Speaker Replacement

Page 16 of 33

● Connect the speaker enclosure

to the wiring

Note – If just replacing the pods,

but not adding ampliers, then

you will connect to OEM plug,

but if you are adding ampliers,

then you will connect to the new

harness.

Also, if replacing the upper dash

speaker, then pass the other

harness from pod up to top

dash location

● Install new speaker enclosure and

secure with (3) Phillips screws

Upper Speaker Replacement

● Lifting the airbag slightly and

install (5) Phillips screws

● Remove (2) Phillips screws,

disconnect wiring and remove

speaker from vehicle

● Carefully clip the airbag into place

Page 17 of 33

Upper Speaker Replacement

● Looking in the glovebox cavity

up high, install (2) 13mm

bolts securing the back of the

passenger side airbag

● Install (3) Phillips screws at

bottom of glovebox opening

● Install glovebox by installing

bottom hinge and pivoting up.

(Also install left side gear arm)

Page 18 of 33

Upper Speaker Replacement

● Install (2) Phillips screw at the

bottom of the passenger airbag

● Clip the airbag cover panel into

place

● Install (2) 10mm bolts securing

the grab handle

Page 19 of 33

Upper Speaker Replacement

● Slide ears on cover into slot and

snap grab handle cover into place

● Install (5) Phillips screws on the

side of dash

● Clip the passenger side dash

cover into place

Page 20 of 33

Page is loading ...

MB QUART Out of stockMBQJ-STG6-1 User manual

This manual is also suitable for

MB QUART Out of stockMBQJ-STG6-1 User manual

Related papers

Other documents