Miller CYLINDER RACKS 195329 AND 195330 Owner's manual
- Category
- Car kits
- Type
- Owner's manual
This manual is also suitable for
OWNER’S MANUAL
© 2008 Miller Electric Mfg. Co.
FORM: OM-6619 220 984D
2008−9
Cylinder Racks 195329 and 195330
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
Beware of electric shock from wiring. Stop engine and
disconnect negative (−) cable from battery before install-
ing this kit. Reinstall all panels and covers.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Falling equipment can cause serious personal injury and
equipment damage. Use lifting eye to lift unit and properly
installed accessories only, NOT gas cylinders. Do not
exceed maximum lifting eye weight rating. Lift and sup-
port only with proper equipment and correct procedures.
NOTICE
Indicates statements not related to personal injury.
Indicates special instructions.
Wear safety glasses with side shields.
1. Assembling Of Shielding Gas Cylinder Rack (195 330)
1 604224 Screw, 250−20x .75 Hexwhd.50d Stl
Pld Slffmg Tap−rw (8)
2 220635 Bracket, Support Tank Weldment (1)
3 188441 Chain, Weldless 2/0 X 31. Bright Zinc
Pld (1)
4 602159 Screw, 312−18x .75 Hexwhd.66d Stl
Pld Slffmg Tap−rw (4)
5 220586 Tray, Mtg Gas Cylinder (1)
Be sure to provide model when ordering replacement
parts.
803 950−B
Description (Qty)
Part
No.
Item
No.
Tools Needed:
7/16, 1/2 in
3/8, 1/2 in
Remove and discard
existing hardware
before installing tray.
Use on
diesel
models
only.
1
2
3
4
5
OM-6619 Page 2
2. Assembling LP Gas Cylinder Rack (195 329)
5
4
3
2
1
803 951−B
Description (Qty)
Part
No.
Item
No.
1 220587 Tray, Mtg LP Gas Tank (1)
2 221382 Latch, Strap LP Tank (1)
3 221381 Strap, LP Tank (1)
4 222350 Nut, Latch,Strap Lp Tank (1)
5 604224 Screw, 250−20x .75 Hexwhd.50d Stl Pld Slffmg Tap−rw (4)
6 602159 Screw, 312−18x .75 Hexwhd.66d Stl Pld Slffmg Tap−rw (4)
7 087318 Clamp, Stl Cush 1.000 Dia X .406 Mtg Hole (1)
8 010910 Washer, Flat .406idx0.812odx.065t Stl Pld Ansi.375 (4)
9 601871 Nut, 375−16 .68hex .25h Stl Pld (4)
170587 Hose, W/Fittings LP Gas (1)
221283 Tubing, Corrugated Plastic Slit 1.000 Dia X 36.000 (1)
170630 Label, Warning LP Gas Burns Or Explodes Easily (1)
Be sure to provide model when ordering replacement parts.
Tools Needed:
7/16, 1/2 in
3/8, 1/2 in
Adjust latch tension
so tank is secure.
LP Tank
Side View − Latch Open
Side View − Latch Closed
Remove and discard
existing hardware be-
fore installing tray.
Route LP gas hose
through opening in base.
Assembly:
Slide tubing onto LP gas hose.
Route LP gas hose from tank through
clamp before tightening hardware
6
7
8
9
-
1
-
2
Miller CYLINDER RACKS 195329 AND 195330 Owner's manual
- Category
- Car kits
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller MB000001 Owner's manual
-
-
-
-
-
-
-
Miller RUNNING GEAR, BOBCAT 200 AIR PAK (301460) Owner's manual
-
-
Miller BIG BLUE 400P (PERKINS) Owner's manual