Schumacher INC-7A-OBD - Memory Saver Owner's manual

Brand: Schumacher

Model: INC-7A-OBD - Memory Saver

Category: Battery chargers

Type: Owner's manual

This manual is also suitable for

INC-7A-OBD

0099000873-01

Model / Modelo / Modèle :

INC-7A-OBD

OWNERS MANUAL

MANUAL DEL USUARIO

GUIDE D’UTILISATION

READ THE ENTIRE MANUAL BEFORE USING THIS PRODUCT.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

LEA EL MANUAL COMPLETO ANTES DE UTILIZAR ESTE PRODUCTO. CUALQUIER

FALLA PODRÍA RESULTAR EN SERIAS LESIONES O PODRÍA SER MORTAL.

LIRE ENTIÈREMENT LE GUIDE AVANT D’UTILISER CE PRODUIT. L’ÉCHEC DE FAIRE

AINSI PEUT S’ENSUIVRE DANS LA BLESSURE SÉRIEUSE OU LA MORT.

CONTAINS SEALED NON-SPILLABLE LEAD-ACID BATTERY.

MUST BE DISPOSED OF PROPERLY.

CONTIENE UNA BATERÍA SELLADA DE ÁCIDO-PLOMO NO

DERRAMABLE QUE DEBE DESECHARSE APROPIADAMENTE.

CONTIENT UNE BATTERIE À L’ACIDE QUI DOIT ÊTRE

DISPOSÉ CORRECTEMENT.

WARNING: Possible explosion hazard. Contact with battery acid may cause

severe burns and blindness. Keep out of reach of children.

ADVERTENCIA: Posible Riesgo de una explosión. El contacto con una batería de

ácido puede causar quemaduras y ceguera. Manténgase alejado de los niños.

AVERTISSEMENT : Hasard d’explosion possible. Contact avec l’acide de batterie

peut provoquer sévère brûle et la cécité. Ne le laissez pas a la portée des enfants.

Memory Saver

Conservador de Memoria

Économiseur de Mémoire

DO NOT RETURN THIS PRODUCT TO THE STORE!

Contact Customer Service for assistance:

Phone: 800-621-5485 • Email: [email protected]

Web: www.batterychargers.com

¡NO LO DEVUELVA ESTE PRODUCTO A LA TIENDA!

Contacte Servicios al Cliente para asistencia:

Teléfono: 800-621-5485 • Correo Electrónico: [email protected]

Sitio Red: www.batterychargers.com

NE PAS RETOURNER LE PRODUIT AU MAGASIN!

Contactez le service clientéle pour l’aide :

Téléphone : 800-621-5485 • E-mail : [email protected]

Site web : www.batterychargers.com

• 2 •

IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.

SAVE THESE INSTRUCTIONS. Charge the memory saver’s internal battery

immediately after purchase, after every use and every 30 days. This manual will show

you how to use your memory saver safely and effectively. Please read, understand and

follow these instructions and precautions carefully, as this manual contains important

safety and operating instructions. The safety messages used throughout this manual

contain a signal word, a message and an icon.

The signal word indicates the level of the hazard in a situation.

Indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided, could result in

death or serious injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided, could result in

moderate or minor injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided, could result in

damage to the equipment, vehicle or property.

Pursuant to California Proposition 65, this product contains chemicals known to

the State of California to cause cancer and birth defects or other reproductive

harm. Wash hands after handling.

Some vehicle manufacturers do not allow the use of a memory saver through

the OBDII. Consult the vehicle manufacturer before use, to determine if a

memory saver is acceptable for use on the vehicle.

1. IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS.

This manual contains important safety and operating instructions.

RISK OF ELECTRIC SHOCK OR FIRE.

1.1 Read the entire manual before using this product. Failure

to do so could result in serious injury or death.

1.2 This memory saver is not intended for use by persons

(including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge.

1.3 Children should be supervised to ensure they do not play with the memory saver.

1.4 Do not put ngers or hands into any of the memory saver’s outlets.

1.5 Do not expose the memory saver to rain or snow.

1.6 Use only recommended attachments. Use of an attachment not recommended or sold

by Schumacher

Electric Corporation may result in a risk of re, electric shock or injury

to persons or damage to property.

1.7 Do not operate the memory saver with damaged cables; have the cable replaced

immediately by a qualied service person.

1.8 Do not operate the memory saver if it has received a sharp blow, been dropped or

otherwise damaged in any way; take it to a qualied service person.

1.9 Do not disassemble the memory saver; take it to a qualied service person when service

or repair is required. Incorrect reassembly may result in a risk of re or electric shock.

RISK OF EXPLOSIVE GASES.

1.10 WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS

DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING

NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST

IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU

USE THE MEMORY SAVER.

• 3 •

2. PERSONAL PRECAUTIONS

RISK OF EXPLOSIVE GASES. A SPARK NEAR

THE BATTERY MAY CAUSE A BATTERY

EXPLOSION. TO REDUCE THE RISK OF A

SPARK NEAR THE BATTERY:

2.1 NEVER smoke or allow a spark or ame in

the vicinity of a battery or engine.

2.2 Remove personal metal items such as rings, bracelets, necklaces and watches when

working with a lead-acid battery. A lead-acid battery can produce a short-circuit current

high enough to weld a ring or the like to metal, causing a severe burn.

2.3 Be extra cautious, to reduce the risk of dropping a metal tool onto the battery. It might

spark or short-circuit the battery or other electrical part that may cause an explosion.

2.4 Do not permit the internal battery of the memory saver to freeze. Never charge a

frozen battery.

2.5 Consider having someone nearby to come to your aid when you work near a

lead-acid battery.

2.6 Have plenty of fresh water and soap nearby in case battery acid contacts your skin,

clothing or eyes.

2.7 Wear complete eye and body protection, including safety goggles and protective

clothing. Avoid touching your eyes while working near the battery.

2.8 If battery acid contacts your skin or clothing, immediately wash the area with soap and

water. If acid enters your eye, immediately ood the eye with cold running water for at

least 10 minutes and get medical attention right away.

2.9 If battery acid is swallowed accidentally, drink milk, water or egg whites. DO NOT induce

vomiting. Seek medical attention immediately.

3. CHARGER AND AC POWER CORD CONNECTIONS

RISK OF ELECTRIC SHOCK OR FIRE.

3.1 The memory saver’s charger is for use on a nominal 120

volt circuit. The extension cord must be plugged into an outlet

that is properly installed and grounded in accordance with all

local codes and ordinances. The extension cord pins must t

the receptacle (outlet). Do not use with an ungrounded system.

NOTE: Pursuant to Canadian Regulations, use of an adapter plug is not allowed in

Canada. Use of an adapter plug in the United States is not recommended and should

not be used.

3.2 To reduce the risk of damage to the electric plug or cord, pull by the plug rather than the

cord when disconnecting the memory saver’s charger.

4. INSTALLATION INSTRUCTIONS

Remove all cord wraps and uncoil the cables prior to using the memory saver.

• 4 •

5. FEATURES

1. Charging Status Lights

2. Internal Battery Status Lights

3. Internal Battery Status Test Switch

4. OBD (On Board Diagnostic) Connector with a 6 Foot Cable

5. Internal Battery Charger Plug

6. 12V DC Power Outlet (On Back, Not Shown)

7. Velcro Strap (not shown)

6. CHARGING THE INTERNAL BATTERY OF THE MEMORY SAVER

IMPORTANT: CHARGE IMMEDIATELY AFTER PURCHASE, AFTER EACH USE

AND EVERY 30 DAYS TO KEEP THE MEMORY SAVER’S INTERNAL BATTERY

FULLY CHARGED.

6.1 Use of an improper extension cord could result in a risk of re and electric shock. When

an extension cord is used, make sure:

• That the pins on the plug of the extension cord are the same number, size and shape

as those of the plug on the memory saver charger.

• That the extension cord is properly wired and in good electrical condition.

• That the extension cord has a wire size of 18 gauge (AWG) [0.82 mm

] or larger and

is 50 feet (15.24 meters) long or less.

6.2 To reduce the risk of electric shock, unplug the memory saver charger from the outlet

before attempting any maintenance or cleaning.

6.3 When charging the internal battery, work in a well ventilated area and do not restrict the

ventilation in any way.

6.4 LED Indicators:

To check the internal battery’s charge status, press the Battery Status button on the front

of the memory saver.

The LED lights will indicate the charge level as follows:

• A red LED indicates a 50% or less charge and you should immediately recharge

the memory saver.

• A yellow LED indicates a 50 to 75% charge. The memory saver may be used but

should be recharged as soon as possible.

• A green LED indicates the internal battery is fully charged.

• The CHARGING (red) LED indicates the memory saver is charging (connected

to an AC power source.) At full charge, the CHARGED (green) LED will light.

6.5 Charging the Internal Battery using the Built-In Charger:

1. To charge, plug an 18 gauge (AWG) or larger extension cord into the charger

plug on the left side of the memory saver. (Extension cord not included; must be

purchased separately.)

2. Plug the extension cord into a 120V AC electrical wall outlet.

• 5 •

3. The CHARGING (red) LED will light, indicating charging.

4. The CHARGED (green) LED will light when the battery has reached full charge.

This could take up to 72 hours, depending on the age and condition of the battery.

The charger will automatically go into maintain mode and maintain the battery at full

charge without damaging it.

5. Charge the memory saver as soon as possible after each use.

6.6 You may also charge the internal battery while driving, using a male-to-male

charger cable (p/n 94500109 – not included). NOTE: Use a male-to-male adaptor only

for charging the internal battery. You must use the OBD Connector to save memory.

IMPORTANT: DO NOT CHARGE INTERNAL BATTERY FOR MORE THAN 30

MINUTES OR LEAVE THE BATTERY UNATTENDED. IT COULD EXPLODE, CAUSING

PROPERTY DAMAGE OR PERSONAL INJURY.

1. Make sure the car is running.

2. Insert one end of the accessory cable into the 12V DC power outlet.

3. Insert the other end of the accessory cable into the vehicle’s accessory outlet

(lighter socket). NOTE: The CHARGING (red) LED and the CHARGED (green) LED

do not operate during this method of charging. Using this method to charge the

battery overrides the maintain mode and the battery can be overcharged.

4. Monitor the progress of the charge by pressing the Battery Status button on the front

of the unit. When it reaches a full (100%) charge, disconnect the accessory cable

from the memory saver, then from the lighter socket of the vehicle.

NOTE: Completely disconnect the charger cable when the engine is not running.

7. USING THE MEMORY SAVER

Use the memory saver to save the vehicle’s on-board diagnostic computer settings

(radio programs, diagnostic codes, etc.) while the battery is disconnected from the

vehicle during repair or maintenance.

Some vehicle manufacturers do not allow the use of a memory saver

through the OBDII. Consult the vehicle manufacturer before use, to

determine if a Memory Saver is acceptable for use on the vehicle.

7.1 Make sure that the memory saver’s internal battery is fully charged. See LED

INDICATORS section (6.4).

7.2 Turn off the vehicle and make sure all accessories are off.

7.3 Wait at least 30 minutes before using the memory saver. This ensures that the

accessories are no longer drawing current from the car battery.

7.4 Connect the memory saver’s OBD connector to the vehicle’s OBD plug. Make sure the

connector is fully engaged.

7.5 Disconnect the vehicle’s battery cables and cover the positive and negative cables with

an insulator, such as electrical tape. This prevents the connectors from touching metal,

each other, or the chassis and causing a short circuit, due to the vehicle’s electrical

system receiving power from the memory saver through the OBD connection.

When working with the vehicle’s battery, review all of the battery

manufacturer’s safety instructions, warnings and directives regarding

battery disconnection, removal and replacement.

7.6 Remove the old battery and put the new battery into position.

7.7 Remove the insulator from the positive cable and connect it to the positive terminal of

the new battery.

7.8 Remove the insulator from the negative cable and connect it to the negative terminal of

the new battery.

7.9 Once the new battery is connected, unplug the memory saver’s OBD connector from the

vehicle’s OBD plug.

Charge the memory saver as soon as possible after use.

• 6 •

8. POWERING A 12V DC DEVICE:

The memory saver is a power source for all 12V DC accessories that are equipped with

a 12V accessory plug. Use it for power outages and shing or camping trips.

Do not power a 12V device with the memory saver while using the OBD

connector to power the on-board diagnostic computer. Doing so will

drain the memory saver’s internal battery and reduce available run time.

1. Make sure the device to be powered is OFF before inserting the 12V DC accessory

plug into the 12V DC accessory outlet.

2. Open the protective cover of the DC power outlet on the back of the memory saver.

3. Plug the 12V DC device into the DC power outlet, and turn on the 12V DC device

(if required).

NOTE: If the 12V DC device draws more than 9A, the internal circuit breaker of the memory

saver will trip and disconnect the power to the device. Disconnect the 12V DC device. The

breaker will automatically reset after an overload occurs.

4. When nished, turn off the DC device (if required) and unplug from the DC power outlet.

Extended operation of a 12V DC device may result in excessive battery

drain. Recharge the memory saver immediately after unplugging the

12V DC device.

9. MAINTENANCE INSTRUCTIONS

9.1 Servicing does not require opening the unit, as there are no user-serviceable parts.

9.2 After use and before performing maintenance, unplug and disconnect the memory saver.

9.3 Use a dry cloth to wipe dirt or oil from the cords and the memory saver case.

9.4 Ensure that all of the memory saver components are in place and in good working condition.

9.5 All other servicing should be performed by qualied service personnel.

10. MOVING AND STORAGE INSTRUCTIONS

10.1 Store the memory saver in an upright position. Store inside, in a cool, dry place.

10.2 If the memory saver is moved around the shop or transported to another location, take

care to avoid/prevent damage to the cords and memory saver. Failure to do so could

result in personal injury or property damage.

10.3 Charge the memory saver’s internal battery immediately after purchase, after every

use and every 30 days, to keep fully charged.

Do not use and/or store the memory saver in or on any area or surface

where damage could occur if the internal battery should unexpectedly

leak acid.

• 7 •

11. SPECIFICATIONS

Internal Battery Type Maintenance-Free AGM Lead-Acid

Nominal Voltage 12V DC

Capacity 7 Ah

Connector OBDII

DC Power Outlet Max Continuous Load 12V DC, 9A

Dimensions (H x W x D) 7.5" x 8" x 5.5"

Weight 7.85 lbs.

12. BEFORE RETURNING FOR REPAIRS

When an UNKNOWN OPERATING PROBLEM arises, please read the complete manual

and call the customer service number for information. This will usually eliminate the need

for return.

For information about troubleshooting, call:

Schumacher Electric Corporation Customer Service

1-800-621-5485

Monday – Friday 7:00 a.m. to 5:00 p.m. CST

For REPAIR OR RETURN, contact Customer Service at 1-800-621-5485. DO NOT SHIP

UNIT until you receive a RETURN MERCHANDISE AUTHORIZATION (RMA) number

from Customer Service at Schumacher Electric Corporation.

13. REPLACEMENT PARTS/ACCESSORIES

Male-To-Male Accessory Cable .........................................................................94500109

• 8 •

14. LIMITED WARRANTY

SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,

MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO THE

ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED WARRANTY IS

NOT TRANSFERABLE OR ASSIGNABLE.

Schumacher Electric Corporation (the “Manufacturer”) warrants this memory saver for

one (1) year and the internal battery for ninety (90) days from the date of purchase at

retail against defective material or workmanship that may occur under normal use and

care. If your unit is not free from defective material or workmanship, Manufacturer’s

obligation under this warranty is solely to repair or replace your product, with a new or

reconditioned unit, at the option of the Manufacturer. It is the obligation of the purchaser

to forward the unit, along with proof of purchase and mailing charges prepaid to the

Manufacturer or its authorized representatives in order for repair or replacement to occur.

Manufacturer does not provide any warranty for any accessories used with this product

that are not manufactured by Schumacher Electric Corporation and approved for use

with this product. This Limited Warranty is void if the product is misused, subjected to

careless handling, repaired, or modied by anyone other than Manufacturer or if this unit

is resold through an unauthorized retailer.

Manufacturer makes no other warranties, including, but not limited to, express,

implied or statutory warranties, including without limitation, any implied warranty

of merchantability or implied warranty of tness for a particular purpose. Further,

Manufacturer shall not be liable for any incidental, special or consequential damage

claims incurred by purchasers, users or others associated with this product, including,

but not limited to, lost prots, revenues, anticipated sales, business opportunities,

goodwill, business interruption and any other injury or damage. Any and all such

warranties, other than the limited warranty included herein, are hereby expressly

disclaimed and excluded. Some states do not allow the exclusion or limitation of

incidental or consequential damages or length of implied warranty, so the above

limitations or exclusions may not apply to you. This warranty gives you specic legal

rights and it is possible you may have other rights which vary from this warranty.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND THE

MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO ASSUME

OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER THAN

THIS WARRANTY.

Schumacher

and the Schumacher Logo are registered trademarks

of Schumacher Electric Corporation.

DO NOT RETURN THIS PRODUCT TO THE STORE!

Contact Customer Service for assistance:

Phone: 800-621-5485

Email: [email protected]

Web: www.batterychargers.com

• 9 •

1 YEAR LIMITED

WARRANTY PROGRAM

REGISTRATION

MODEL: _____________________DESCRIPTION: ________________________

This is the only express limited warranty, and the manufacturer neither assumes

nor authorizes anyone to assume or make any other obligation. There is no other

warranty, other than what is described in the product owner’s manual.

The warranty card should be submitted within 30 days of purchase. The customer

must keep the ORIGINAL receipt because it will be required for any warranty claims.

This warranty is not transferable. Send warranty card only.

DO NOT SEND UNIT TO THIS ADDRESS FOR REPAIR.

Mail this card to: Schumacher Electric Corporation

801 Business Center Drive

Mount Prospect, IL 60056-2179

Name ______________________________________________________________

Street Address _______________________________________________________

City ________________________________State _________ Zip Code _________

Phone _____________________Email ___________________________________

Store Name Where Purchased ___________________ Date of Purchase _________

Store Location ____________________ UPC Number ________________________

Serial Number ______________________________________ (SEE PRODUCT)

For faster warranty activation, go to www.batterychargers.com to register your product online.

PROGRAMA DE REGISTRO

DE 1-AÑO DE GARANTÍA

LIMITADA

MODELO: ____________________DESCRIPTIÓN: ________________________

Esta es la única garantía limitada expresa, y el productor no autoriza ni otorga

a alguien a realizar alguna otra obligación. No existe ninguna otra garantía

más que la descrita en el manual del dueño.

La tarjeta de garantía debe enviarse durante los primeros 30 días después de la

compra. El cliente debe mantener el recibo de compra ORIGINAL como

comprobante, el cual le otorga todo derecho a cualquier reclamo de garantía.

Esta garantía no es transferible. Envie tarjeta de garantía solamente.

NO ENVÍE LA UNIDAD A ESTA DIRECCIÓN PARA SU REPARACIÓN.

Enviar esta tarjeta a: Schumacher Electric Corporation

801 Business Center Drive

Mount Prospect, IL 60056-2179

Nombre ____________________________________________________________

Dirección ___________________________________________________________

Ciudad __________________________Estado ____________ C.P. _____________

Tel: ________________________ Correo electrónico _________________________

Nombre de la Tienda donde se Compró ____________ Fecha de compra _________

Localización de la Tienda ____________ Numero de Serie ____________________

Código de barras ___________________________ (CONSULTE EL PRODUCTO)

Para una activación más rápida, visite nuestra página de internet en www.batterychargers.com

SAVE ON POSTAGE! ACTIVATE YOUR WARRANTY ONLINE – THE QUICK AND EASY WAY!

Go to www.batterychargers.com to register your product online.

(No internet access? Send in the completed warranty card.)

¡AHORRE EN EL ENVÍO! ¡ACTIVE SU GARANTÍA EN LÍNEA-LA FORMA MAS RÁPIDA Y FÁCIL!

Visite nuestra página en www.batterychargers.com para registrar su producto en línea.

(¿No tiene acceso al internet? Llene la tarjeta de garantía y envíela.)

Page is loading ...

Schumacher INC-7A-OBD - Memory Saver Owner's manual

Brand: Schumacher

Model: INC-7A-OBD - Memory Saver

Category: Battery chargers

Type: Owner's manual

This manual is also suitable for

INC-7A-OBD

Download PDF

report

in other languages

français: Schumacher INC-7A-OBD - Memory Saver Le manuel du propriétaire
español: Schumacher INC-7A-OBD - Memory Saver El manual del propietario

Schumacher INC-7A-OBD - Memory Saver Owner's manual

This manual is also suitable for

Schumacher INC-7A-OBD - Memory Saver Owner's manual

in other languages

Related papers

Other documents