Bostitch BTE100 User manual

Instruction manual

Manuel d’instructions

Manual de’instrucciones

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA:

LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

BTE100

www.BOSTITCH.com

6.5 A

3/8 Inch (10mm) Drill

Perceuse de 10mm (3/8 po)

Taladro de 10mm (3/8 pulgada)

2

General Power Tool Safety Warnings

WARNING: Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warningS and inStructionS for future reference

The term “power tool” in the warnings refers to your mains-operated (corded) power

tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground

fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the

risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, nonskid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position

before connecting to power source and/ or battery pack, picking up

or carrying the tool. Carrying power tools with your finger on the switch or

energizing power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols

below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may

result in minor or mod er ate injury.

NOTICE: Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.

3

e) Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewelry or long

hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust

collection can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a)

Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from

the power tool before making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power

tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended

could result in a hazardous situation.

5) SERVICE

a)

Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Specific Safety Rules

• Use auxiliary handle(s) if supplied with the tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping surfaces, when performing an operation

where the cutting accessory may contact hidden wiring. Cutting accessory

contacting a “live” wire may make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

• Use clamps or another practical way to secure and support the work piece to a

stable platform. Holding the work by hand or against your body leaves it unstable and

may lead to loss of control.

• Keep your hair, clothing, and gloves away from air vents. Air vents often cover

moving parts in which these items can be caught.

• Hold tool firmly with two hands. Use auxiliary handle if provided. Loss of control can

cause personal injury.

WARNING: Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

  •leadfromlead-basedpaints,

  •crystallinesilicafrombricksandcementandothermasonryproducts,and

•arsenicandchromiumfromchemically-treatedlumber.

Yourriskfromtheseexposuresvaries,dependingonhowoftenyoudothistypeof

work.Toreduceyourexposuretothesechemicals:workinawellventilatedarea,and

workwithapprovedsafetyequipment,suchasthosedustmasksthatarespecially

designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding,

drilling, and other construction activities. Wear protective clothing and wash

exposed areas with soap and water.Allowingdusttogetintoyourmouth,eyes,or

layontheskinmaypromoteabsorptionofharmfulchemicals.

4

WARNING: Use of this tool can generate and/or disperse dust, which may

cause serious and permanent respiratory or other injury. Always use NIOSH/

OSHA approved respiratory protection appropriate for the dust exposure. Direct

particles away from face and body.

• Wear appropriate hearing protection during use. Under some conditions and

duration of use, noise from this product may contribute to hearing loss.

WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT

safety glasses. Also use face or dust mask if cutting operation is dusty.

ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

•

ANSI Z87.1 eye protection (CAN/CPA Z94.3),

•

ANSI S12.6 (S3.19) hearing protection,

•

NOSH/OSHA respiratory protection.

Symbols

The label on your tool may include the following symbols. The symbols and their definitions are as

follows:

V ..................volts A ................... amperes

Hz ................hertz W ..................watts

min ..............minutes

or AC .......alternating current

or DC ...direct current

n

o .................no load speed

................Class I Construction .................earthing terminal

(grounded)

................safety alert symbol

................Class II Construction .../min or rpm...revolutions or

(double insulated) reciprocation per minute

............

Read instruction manual before use

....................Use proper respiratory protection

................Use proper eye protection .................Use proper hearing protection

• Whenusinganextensioncord,besuretouseoneheavyenoughtocarrythecurrent

yourproductwilldraw.Anundersizedcordwillcauseadropinlinevoltageresulting

inlossofpowerandoverheating.Thefollowingtableshowsthecorrectsizetouse

dependingoncordlengthandnameplateampererating.Ifindoubt,usethenext

heaviergage.Thesmallerthegagenumber,theheavierthecord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

  (0-7,6m)(7,6-15,2m)(15,2-30,4m)(30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m)(15,2-30,4m)(30,4-60,9m)(60,9-91,4m)

Ampere Rating

More Not more American Wire Gage

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 NotRecommended

5

FUNCTIONAL DESCRIPTION

Figure A

1. Variable speed switch

2.Lock-onbutton

3.Reversinglever

4.Keylesschuck

5.Beltclip

B

c

d

1

4

a

5

2

3

SAFETY WARNINGS AND INSTRUCTIONS: DRILLS

WARNING: Drillmaystall(ifoverloadedorimproperlyused)causingatwist.Always

expectthestall.Gripthedrillfirmlywithbothhandstocontrolthetwistingactionand

preventlossofcontrolwhichcouldcausepersonalinjury.Ifastalldoesoccur,releasethe

triggerimmediatelyanddeterminethereasonforthestallbeforere-starting.

ASSEMBLY

WARNING:Toreducetheriskofinjury,beforeassembly,makesurethatthetoolis

switched off and unplugged.

INSERTING A DRILL BIT OR OTHER ACCESSORY (FIGURE B)

WARNING: Do not attempt to tighten drill bits (or any other accessory) by

gripping the front part of the chuck and turning the tool on. Damage to the chuck and

personal injury may occur when changing accessories.

WARNING: Always ensure the bit is secure before starting the tool. A loose bit

may eject from tool causing possible personal injury.

Yourtoolfeaturesakeylesschuck(4)forgreaterconvenience.Toinsertadrillbitor

otheraccessory,followthestepslistedbelow.

• Grasptherearhalfofthechuckwithonehandanduseyourotherhandtorotatethe

fronthalfcounterclockwise,asshowninfigure B.Rotatefarenoughsothatthechuck

opens sufficiently to accept the desired accessory.

• Insertthebitorotheraccessoryabout3/4inch(19mm)intothechuckandtighten

securelybyholdingtherearhalfofthechuckandrotatingthefrontportioninthe

clockwisedirection.

• Toreleasetheaccessory,repeatstep1listedabove.

6

REMOVING AND ATTACHING THE CHUCK (FIGURE C)

• Openthechuckasfaraspossible.

• Removethechuckretainingscrew,locatedinthechuck,byturningitclockwiseusinga

screwdriver(lefthandthread).

• TightenanAllenkeyof1/4inchorgreatersize(notsupplied)intothechuckandstrike

itwithasofthammerinacounterclockwisedirectionasshown.

• RemovetheAllenkey.

• Removethechuckbyturningitcounterclockwise.

• Toattachthechuck,screwitontothespindleandsecureitwiththechuckretainingscrew.

OPERATING INSTRUCTIONS

WARNING:To reduce the risk of serious personal injury, read, understand and

follow all safety warnings and instructions prior to using tool.

WARNING: It is important to support the work properly and to hold the drill

firmly with both hands to prevent loss of control which could cause personal injury.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by

gripping the front part of the chuck and turning the tool on. Damage to the chuck

and personal injury may occur when changing accessories.

WARNING: To reduce the risk of injury, always unplug drill from power supply

before making any adjustments or changing accessories.

WARNING: To reduce the risk of injury, let the tool work at its own pace. Do not overload.

SWITCHES (FIGURE D)

• Toswitchthetoolon,depressthevariablespeedswitch(1).Thetoolspeeddepends

on how far you press the switch.

• Forcontinuousoperation,pressthelock-onbutton(2)andreleasethevariablespeed

switch.Thisoptionisavailableonlyatfullspeed.

• Toswitchthetooloff,releasethevariablespeedswitch.Toswitchthetooloffwhenin

continuousoperation,depressthevariablespeedswitchoncemoreandreleaseit.

WARNING: ThedrillshouldonlybelockedONwhenitisheldstationaryinadrill

pressstandorothermeans;NOTBYHAND!Neverunplugthetoolwiththelocking

featureengaged.Todosowillcausethetooltostartimmediatelythenexttimeitis

plugged in.

REVERSING LEVER

Thereversinglever(3)isusedforwithdrawingbitsfromtightholesandremoving

screws.Itislocatedabovethetriggerswitch.Toreversethemotor,releasethetrigger

switchFIRSTandthenpushthelevertotheright.Afteranyreversingoperations,

returnlevertoforwardposition.Neverchangethedirectionofrotationwhilethemotor

is running.

DRILLING

•Alwaysunplugthedrillwhenattachingorremovingaccessories.Whenattaching

accessoriesinthedrillchuck,itisimportanttosecurelytightenthechucktoprevent

slippage.Whenusingakeylesschuck,handtightenfirmly.

•Usesharpdrillbitsonly.

•Supportandsecureworkproperly,asinstructedintheSafetyInstructions.

•Useappropriateandrequiredsafetyequipment,asinstructedinthesafetyinstructions.

•Secureandmaintainworkarea,asinstructedinthesafetyinstructions.

•Runthedrillveryslowly,usinglightpressure,untiltheholeisstartedenoughtokeep

the drill bit from slipping out of it.

•Applypressureinastraightlinewiththebit.Useenoughpressuretokeepthebitbiting

but not so much as to stall the motor or deflect the bit.

•Hold the drill firmly with both hands to control its twisting action.

•Drillsequippedwithasidehandlemustusethesidehandle.

•DONOTCLICKTHETRIGGEROFASTALLEDDRILLOFFANDONINAN

ATTEMPTTOSTARTIT.DAMAGETOTHEDRILLCANRESULT.

•Minimizestallingonbreakthroughbyreducingpressureandslowlydrillingthroughthe

last part of the hole.

•Keepthemotorrunningwhilepullingthebitoutofadrilledhole.Thiswillhelpreduce

jamming.

7

DRILLING IN WOOD

Holes in wood can be made with the same twist drill bits used for metal or with spade

bits.Thesebitsshouldbesharpandshouldbepulledoutfrequentlywhendrillingto

clear chips from the flutes.

DRILLING IN METAL

Useacuttinglubricantwhendrillingmetals.Theexceptionsarecastironandbrass

whichshouldbedrilleddry.Thecuttinglubricantsthatworkbestaresulfurizedcuttingoil

or lard oil.

DRILLING IN MASONRY

Use carbide tipped masonry bits. Refer to Drillingsection.Keepevenforceonthedrill

butnotsomuchthatyoucrackthebrittlematerial.Asmooth,evenflowofdustindicates

the proper drilling rate.

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unitwillnotstart. •Cordnotpluggedin. •Plugtoolintoaworkingoutlet.

  •Circuitfuseisblown. •Replacecircuitfuse.(Ifthe

product repeatedly causes the

   circuitfusetoblow,discontinue

   useimmediatelyandhaveit

   servicedataBostitchservice

   centerorauthorizedservicer.)

 •Circuitbreakeristripped. •Resetcircuitbreaker.(Ifthe

product repeatedly causes the

   circuitbreakertotrip,

discontinue use immediately

   andhaveitservicedataBostitch

   servicecenterorauthorized

   servicer.)  

 •Cordorswitchisdamaged. •Havecordorswitchreplaced

   ataBostitchServiceCenteror

   AuthorizedServicer.

Forassistancewithyourproduct,visitourwebsiteatwww.bostitch.com.foralistof

servicecenters,orcalltheBostitchCustomerCareCenterat(800) 262-2161.

MAXIMUM RECOMMENDED CAPACITIES

CHUCKCAPACITY  3/8in.(9.5mm)

R.P.M.    0–2500

BITS,METALDRILLING  1/2in.(13mm)lowspeed

WOOD,FLATBORING  1-1/4in.(32mm)

MAINTENANCE

Useonlymildsoapanddampclothtocleanthetool.Neverletanyliquidgetinsidethe

tool;neverimmerseanypartofthetoolintoaliquid.

REPLACEMENT PARTS

Useonlyidenticalreplacementparts.Forapartslistortoorderparts,visitourservice

website at www.bostitch.com. You can also order parts from your nearest Bostitch

FactoryServiceCenterorBostitchAuthorizedWarrantyServiceCenter.Or,youcancall

ourCustomerCareCenterat(800)2622161.

SERVICE AND REPAIRS

Allqualitytoolswilleventuallyrequireservicingand/orreplacementofparts.For

informationaboutBostitch,itsfactoryservicecentersorauthorizedwarrantyservice

centers,visitourwebsiteatwww.bostitch.comorcallourCustomerCareCenterat

(800)2622161.Allrepairsmadebyourservicecentersarefullyguaranteedagainst

8

defectivematerialandworkmanship.Wecannotguaranteerepairsmadeorattempted

by others.

YoucanalsowritetousforinformationatBostitch,701E.JoppaRoad,Towson,

Maryland21286-Attention:ProductService.Besuretoincludealloftheinformation

shownonthenameplateofyourtool(modelnumber,type,serialnumber,etc.).

ACCESSORIES

WARNING: Sinceaccessories,otherthanthoseofferedbyBostitchhavenot

beentestedwiththisproduct,useofsuchaccessorieswiththistoolcouldbe

hazardous.Toreducetheriskofinjury,onlyBostitchrecommendedaccessoriesshould

be used with this product.

AcompletelineofaccessoriesisavailablefromyourBostitchFactoryServiceCenter

oraBostitchAuthorizedWarrantyServiceCenter.PleasevisitourWebSitewww.

bostitch.com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

Bostitchwillrepairorreplace,withoutcharge,anydefectsduetofaultymaterials

orworkmanshipforthreeyearsfromthedateofpurchasefortools(twoyearsfor

batteries).Thiswarrantydoesnotcoverpartfailureduetonormalwearortoolabuse.

Forfurtherdetailofwarrantycoverageandwarrantyrepairinformation,visitwww.

bostitch.com or call (800) 262-2161. This warranty does not apply to accessories or

damagecausedwhererepairshavebeenmadeorattemptedbyothers.Thiswarranty

givesyouspecificlegalrightsandyoumayhaveotherrightswhichvaryincertainstates

orprovinces.

Inadditiontothewarranty,Bostitchtoolsarecoveredbyour:1YEARFREESERVICE:

Bostitchwillmaintainthetoolandreplacewornpartscausedbynormaluse,forfree,

any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the

performanceofyourBostitchPowerToolforanyreason,youcanreturnitwithin90

daysfromthedateofpurchasewithareceiptforafullrefund–noquestionsasked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For

productssoldinLatinAmerica,seecountryspecificwarrantyinformationcontainedin

thepackaging,callthelocalcompanyorseewebsiteforwarrantyinformation.

Toregisteryourtoolforwarrantyservicevisitourwebsiteatwww.bostitch.com

WARNING LABEL REPLACEMENT

Ifyourwarninglabelsbecomeillegibleoraremissing,call(800)262-2161forafree

replacement.

Imported by Bostitch

701E.JoppaRoad

Towson,Maryland21286

Page is loading ...

2828

Catalog Numbers BTE100 Form # 90597557

June 2013 Printed in China

Bostitch BTE100 User manual

This manual is also suitable for

Bostitch BTE100 User manual

in other languages

Related papers

Other documents