Simplicity HGS, 8000 SERIES 50HZ User manual

Brand: Simplicity

Model: HGS, 8000 SERIES 50HZ

Category: Power generators

Type: User manual

This manual is also suitable for

040496-01

Not for

Reproduction

Generator

Home Generator Systems

User’s Instructions

Series 8000

80021419 Revision -

Not for

Reproduction

These original instructions contain safety information to make you aware of the hazards and risks associated with

residential generator systems and how to avoid them. This product is intended for use as an optional system which provides

an alternate source of electric power and to serve loads such as heating, refrigeration systems, and communication systems

that, when stopped during any power outage, could cause discomfort or inconvenience.

IMPORTANT - READ INSTRUCTIONS IN FULL.

IMPORTANT - SAVE THIS MANUAL FOR FUTURE REFERENCE.

Fill out the information below.

Date of Purchase

Generator

Model Number

Model Revision

Serial Number

Engine

Model Number

Serial Number

Briggs & Stratton Power Products Group, LLC

P.O. Box 702

Milwaukee, WI 53201-0702

reproduced or transmitted in any form without the express written

permission of Briggs & Stratton Power Products Group, LLC.

This generator is declared compliant to

IP23W requirements per IEC 60529

Not for

Reproduction

Table of Contents

SAFETY INSTRUCTIONS ................................................................................. 4

Safety Signs .................................................................................................................. 4

Safety Alerts .................................................................................................................. 4

SAFETY RULES AND INFORMATION ............................................................. 7

Safety Rules .................................................................................................................. 7

Storage And Disposal Of Generator ............................................................................. 7

Equipment Description .................................................................................................. 7

User .............................................................................................................................. 7

Skilled Person .............................................................................................................. 7

User Responsibilities .................................................................................................... 7

CONTROLS ....................................................................................................... 8

System Control Panel ................................................................................................... 8

Menu ............................................................................................................................ 9

General Set Up Screen ............................................................................................... 10

Control Panel Prompts ................................................................................................ 11

Automatic Mode .......................................................................................................... 11

General System Parameters ....................................................................................... 11

Advanced Settings Screen .......................................................................................... 12

OPERATION ....................................................................................................13

Automatic Operation Sequence .................................................................................. 13

Utility Voltage Dropout Sensor .................................................................................... 13

Engine Cool-Down Timer ............................................................................................ 13

Exercise Timer ............................................................................................................ 13

MAINTENANCE ...............................................................................................13

Servicing The System ................................................................................................. 13

Before Servicing Generator ......................................................................................... 13

After Servicing Generator ............................................................................................ 13

Service Code Detection System ................................................................................. 13

Reset Service Code Detection System ....................................................................... 14

Maintenance Schedules .............................................................................................. 15

Maintenance Schedule for User .................................................................................. 15

Maintenance Schedule for Skilled Person .................................................................. 15

Generator Maintenance for User ................................................................................. 16

Maintain Carbon Monoxide Detectors ......................................................................... 16

Maintain Smoke Detectors .......................................................................................... 16

Clean Generator.......................................................................................................... 16

TROUBLESHOOTING ..................................................................................... 17

Troubleshooting for User............................................................................................. 17

EQUIPMENT SPECIFICATIONS .....................................................................18

WARRANTY .....................................................................................................19

Not for

Reproduction

Safety Signs

Safety Alerts

The safety alert symbol indicates a potential personal injury hazard. A signal word, such as DANGER, WARNING, or

CAUTION, is used with the alert symbol to designate a degree or level of hazard seriousness. A safety symbol may be used

to represent the type of hazard.

DANGER

Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

WARNING

Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.

CAUTION

Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.

NOTICE

The manufacturer cannot possibly anticipate every possible circumstance that might involve a hazard. The warnings in this

manual, and the tags/decals axed to the generator are, therefore, not all-inclusive. If you use a procedure, work method or

operating technique that the manufacturer does not specically recommend, you must satisfy yourself that it is safe for you

and others. You must also make sure that the procedure, work method or operating technique that you choose does not render

the generator unsafe.

SAFETY INSTRUCTIONS

Flammable material

Toxic fumes

Lift hazard

Refer to instruction

manual/booklet

Corrosive substanceAutomatic start-up

Hot surfaceRotating parts

Electrical shockExplosive material

Not for

Reproduction

SAFETY INSTRUCTIONS cont.

WARNING

Exhaust heat/gas could ignite

combustibles or structures resulting in death or

serious injury. Contact with muffler area could

cause burns resulting in serious injury.

• Do allow equipment to cool before touching.

• Do avoid hot exhaust gases.

• Do have smoke detectors installed

and maintained indoors according

to the manufacturer’s instructions/

recommendations. Carbon monoxide

detectors cannot detect smoke.

DO NOT

• Do not touch hot parts.

• Do not smoke around generator.

WARNING

Running engine produces carbon

monoxide, an odorless, poisonous gas.

Breathing carbon monoxide could result in

death, serious injury, headache, fatigue,

dizziness, vomiting, confusion, seizures, nausea

or fainting.

• Do have carbon monoxide detectors

installed and maintained indoors

according to manufacturer’s instructions/

recommendations. Smoke alarms cannot

detect carbon monoxide gas.

WARNING

Electrical Shock - If you must work

around a unit while it is operating, stand

on an insulated dry surface to reduce risk

of shock hazard. Despite the safe design

of the generator, operating this equipment

imprudently, neglecting its maintenance or

being careless could result in death or serious

injury.

DO NOT

• Do not touch bare wires or bare

receptacles.

• Do not use generator with electrical cords

which are worn, frayed, bare or otherwise

damaged.

• Do not handle generator or electrical cords

while standing in water, while barefoot, or

while hands or feet are wet.

In case of an accident caused by electrical

shock, immediately shut down the source of

electrical power and contact the local authorities

or emergency response units. Avoid direct

contact with the victim.

WARNING

Storage batteries

give off explosive hydrogen gas during

recharging. The slightest spark will ignite

hydrogen and cause explosion, resulting in

death or serious injury. Battery electrolyte fluid

contains acid and is extremely caustic. Contact

with battery contents could cause severe

chemical burns. A battery presents a risk of

electrical shock and high short circuit current.

DO NOT

• Do not allow an open flame, spark, heat, or

lit cigarette in vicinity of battery.

• Do not open or mutilate battery.

Not for

Reproduction

SAFETY INSTRUCTIONS cont.

WARNING

Propane and Natural Gas are

extremely flammable and explosive, which could

cause burns, fire or explosion resulting in death

or serious injury. The slightest spark could ignite

these fuels and cause an explosion. LP gas

is heavier than air and will settle in low areas.

Natural gas is lighter than air and will collect in

high areas.

• Do keep the area near the generator clean

and free of debris.

DO NOT

• Do not operate engine if smell of fuel is

present or other explosive conditions exist.

• Do not smoke around generator.

• Do not have any open flames around

generator.

CAUTION

Auto start of Machinery - Installing the

15 Amp fuse could cause the engine to crank

and start at any time without warning resulting in

minor to moderate injury.

• Do remove the 15A fuse before maintaining

and/or servicing generator.

DO NOT

• Do not reinstall 15A fuse until after

maintaining and/or servicing generator

Not for

Reproduction

SAFETY RULES AND INFORMATION

SHUT OFF GENERATOR AND CONTACT

A SKILLED PERSON IF:

• ELECTRICAL OUTPUT IS LOST

• EQUIPMENT SPARKS, SMOKES, OR EMITS FLAMES

• GENERATOR VIBRATES EXCESSIVELY

• GENERATOR MAKES UNUSUAL NOISES

Storage And Disposal Of Generator

The generator is designed for long term service as a backup

generator.

If it becomes necessary to take the generator out of service

for an extended period, contact a skilled person.

Follow your local ordinance for proper disposal of the

generator. Contact a skilled person for disposal information.

Equipment Description

This product is intended for use as an optional system

which provides an alternate source of electric power and

to serve loads such as heating, refrigeration systems, and

communication systems that, when stopped during any

power outage, could cause discomfort or inconvenience.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter, or otherwise improve the product

and this document at any time without prior notice. These

instructions are specically targeted for the user.

User

Individual or organization that uses products.

Skilled Person

Individual with relevant technical education, training and/

or experience enabling him or her to perceive risks and to

avoid hazards occurring during use of a product.

User Responsibilities

• Read and follow the instructions given in the User’s

Instructions.

• Follow a regular maintenance schedule for your

generator, as specified in the User’s Instructions.

• The illustrations provided in this manual are for typical

circumstances and are meant to familiarize you with the

maintenance and repairs.

• Maintenance and repairs in this manual are

distinguished between User and Skilled Person. User

should only attempt to repair or maintain what the

manufacturer recommends/instructs. See Maintenance

Schedules.

• If the User attempts to repair or maintain generator

outside the scope of these instructions, the warranty on

the generator will be VOID.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Smoke alarms cannot

detect carbon monoxide gas.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

Safety Rules

NOTICE

Improper treatment of generator could

damage it, shorten its life, and void warranty

1. Read, understand, and follow all instructions in the

manual and on the generator before starting equipment.

2. Use generator only for intended uses.

3. Adequate, unobstructed flow of cooling and ventilating

air is critical to correct generator operation.

4. Remain alert at all times while working on this

equipment. Do not work on the equipment when you are

physically or mentally fatigued.

5. If connected devices overheat, turn them off and

disconnect them from generator.

6. Do not modify generator in any way.

7. Do not expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

8. Do not insert any objects through cooling slots.

9. Do not use the generator or any of its parts as a step.

Stepping on the generator could break parts. This may

result in dangerous operating conditions from leaking

exhaust gases, fuel leakage, oil leakage, etc.

10. Do not allow unqualified persons or children to operate

or service generator.

11. After the system is installed, the generator may crank

and start at any time, without warning. To prevent

possible injury while working on equipment, depress

the OFF button on the generator control panel. Then

remove the 15 A fuse from the generator control panel.

Not for

Reproduction

System Control Panel

The generator control panel, located inside generator

housing, is shown in the figure below.

A. Menu/Programming Navigation Buttons - See Menu

section for details.

B. USB Port - Skilled Person Use ONLY.

C. Generator Operation Control Buttons -

AUTO - Normal operating position. Press and hold

button to put generator into Automatic Mode. If an

utility power outage is sensed, the generator will start.

When utility power is restored, auto lets the engine

stabilize internal temperatures, shuts off the generator,

and waits for the next utility outage.

AUTO LED - LED lights when unit is placed into AUTO

mode. LED blinks if exercise cycle is not set or is set to

OFF.

OFF - Turns off running generator, prevents it from

starting, and resets any detected fault conditions. To

reset service codes, press and hold OFF button for

more than 5 seconds.

MANUAL - Manually starts the generator.

D. 15 Amp Fuse - Protects the generator DC control

circuits. If the fuse has ‘blown’ (melted open) or was

removed the engine cannot crank or start. Replace the fuse

using only an identical ATO 15A fuse. One spare fuse is

supplied with the unit.

E. Cover - This protective cover must be opened to

access the fuse and the USB port.

F. Digital Display - Displays generator mode, menu

options, service codes, and service engine indicators.

Figure 16 Control Panel

CONTROLS

Not for

Reproduction

The following chart shows the icons for the buttons that control the system control panel.

The following chart describes key sequences for accessing different programming modes;

ENTERS THE MENU (VIEW SETTINGS).

PRESS TO CONFIRM SELECTION WHEN PROGRAMMING.

ESCAPE (EXIT) RETURNS TO LAST MENU ITEM.

RIGHT ARROW

TOGGLES THROUGH MENU OPTIONS.

SETS SYSTEM PARAMETERS.

LEFT ARROW

TOGGLES THROUGH MENU OPTIONS.

SETS SYSTEM PARAMETERS.

MANUAL MODE

MANUALLY STARTS THE GENERATOR. PRESS AND HOLD

BUTTON TO START THE GENERATOR.

OFF

TURNS OFF RUNNING GENERATOR, PREVENTS GENERATOR

FROM STARTING, AND RESETS ANY DETECTED FAULTS.

AUTOMATIC MODE

NORMAL OPERATING POSITION. PRESS AND HOLD BUTTON

TO PUT GENERATOR INTO AUTOMATIC MODE. IF A UTILITY

POWER OUTAGE IS SENSED, THE SYSTEM WILL START THE

GENERATOR. WHEN UTILITY POWER IS RESTORED, AUTO LETS

THE ENGINE STABILIZE INTERNAL TEMPERATURES, SHUTS OFF

THE GENERATOR, AND WAITS FOR THE NEXT UTILITY POWER

OUTAGE.

GENERAL

SET-UP

PRESS AND HOLD [LEFT ARROW AND RIGHT ARROW]

FOR THREE SECONDS TO ENTER THE PROGRAM

MODE.

ADVANCED

SETTINGS

PRESS AND HOLD [LEFT ARROW AND RIGHT ARROW

AND ESC] FOR THREE SECONDS TO ENTER THE

ADVANCED SETTINGS MODE.

WIRELESS

LINK MODE

PRESS AND HOLD [MENU AND ESC] FOR THREE

SECONDS TO ENTER THE WIRELESS LINKING MODE

(WHERE AVAILABLE).

Figure 17 Control Panel Icons

Figure 18 Control Panel Sequences

CONTROLS cont.

NOTICE

Link Mode will time out in 5 minutes

Not for

Reproduction

CONTROLS cont.

General Set Up Screen

NOTICE

Control panel will automatically reset during programming, if no buttons

are pressed for 30 seconds.

SET DATE

If set to OFF, display will read:

EXERCISE CYCLE OFF

YEAR

FLASHING

MONTH

FLASHING

DAY##

FLASHING

SET TIME

HOURS

FLASHING

MINUTES

FLASHING

AM/PM

FLASHING

or or

DAY OF WEEK

FLASHING

HOURS

FLASHING

MINUTES

FLASHING

AM/PM

FLASHING

SET EXERCISE

CYCLE

EVENT LOG

Display will scroll last service code event, date, time,

and ambient temperature of when the event occurred.

OFF

Figure 19 General Set Up Screen

For general set up, press and hold the left arrow and right arrow for 3 seconds. Follow the prompts as outlined below.

NOTE: Date and Time were set at the factory and stored in the control panel memory. The Exercise Cycle was also set at

the factory for Tuesdays, at 2:00 P.M. To update or change these settings, follow the steps below.

Not for

Reproduction

Control Panel Prompts

Automatic Mode

In Automatic Mode, the display screen will display via

scrolling text:

• GENERATOR READY - if the generator is in standby

and utility power is present.

• GENERATOR ON - if the generator is running and utility

power is not present.

• SERVICE CODE - if a system fault has been detected.

General System Parameters

To view general system parameters, press the MENU

button.

The following will scroll across the digital display and then

move to the next item:

• Run time

• Date

• Time

• Exercise Cycle date and start time

Press the LEFT ARROW or RIGHT ARROW at any time to

move to the next item.

Press ESCAPE to go back to GENERATOR READY.

The control board will reset to GENERATOR READY if no

user inputs are made for 10 seconds after all the items have

been displayed.

AUTOMATIC MODE

GENERATOR READY OR SERVICE CODE DESCRIPTION

(When Generator NOT Running - Auto Mode)

GENERATOR ON

(When Generator Running - Auto Mode)

(MENU)

RUN TIME

TIME

DATE

EXERCISE CYCLE

CONTROLS cont.

Figure 20 Control Panel Prompts

Figure 21 General System Parameters

Not for

Reproduction

Advanced Settings Screen

Advanced setting parameters are preset at the factory for a typical installation. To view Advanced Settings items and/or to

change items, follow the instructions listed below.

Advanced settings are critical to the operation of the generator. Careful consideration should be taken when

working in the Advanced Settings menu. Exercise caution when selecting and verifying parameters for the

generator and region where the generator is being operated. Confirm all settings before operating the generator

for the first time.

For advanced menu items, press and hold the left arrow, right arrow, and escape key

for 3 seconds. Follow the

prompts as outlined below.

CONTROLS cont.

NOTICE

In the Advanced Setting menu, a three button access code (left arrow, right

arrow, and escape key), must be pressed simultaneously once to enter the

menu and again to change any setting. After each conrmation of a setting, the

selection will display solid for 2 seconds before moving to the next program item

Figure 22 Advanced Settings Screen

kVa

FLASHING

50/60 Hz

FLASHING

PHASE

VOLT S

SOFTWARE

Version Displayed

VOLTS

FLASHING

SINGLE

THREE

FLASHING

E-Governor

Check

Stepper Motor

will sweep through throttle

range for visual verication

Not applicable

to this model

Not for

Reproduction

OPERATION

Automatic Operation Sequence

The generator’s control board constantly monitors utility

voltage. Should utility voltage drop below a preset level, the

control board signals the engine to crank and start. When

the utility voltage is restored above a preset voltage level,

the engine is signaled to shut down. The system operation

is not adjustable and is sequenced by sensors and timers

on the control board as follows:

Utility Voltage Dropout Sensor

• This sensor monitors utility source voltage.

• If utility source voltage drops below 70% of the nominal

supply voltage, the sensor energizes a 3 second timer.

The timer is used to sense low voltage conditions.

• Once the time has expired, the engine will crank and

start.

Engine Cool-Down Timer

When utility power is sensed and the load transfers to the

utility source, the engine will go into a cool down period as

described below:

• If the generator has run for MORE than 5 minutes, once

the utility transfer occurs, the engine will continue to run

for about 1 minute before shutting down.

• If the generator has run for LESS than 5 minutes, once

the utility transfer occurs, the engine will continue to run

until 5 minutes has elapsed before shutting down.

Exercise Timer

The generator is equipped with a weekly exercise timer.

During the exercise period, the generator runs for 20

minutes and then shuts down.

The generator does not supply power to the home

during the exercise cycle. The control panel displays

“GENERATOR READY” during the exercise cycle.

The generator is set to run the exercise cycle on Tuesday

at 2:00 PM. To change exercise cycle timer settings refer to

the General Set-up Screen flow chart in the Menu section.

Servicing The System

Before Servicing Generator

Always perform the following steps BEFORE servicing

generator:

1. Close manual fuel shut-off valve.

2. Open roof of generator.

3. Set generator’s circuit breaker to its OFF position.

4. Press and hold the control board OFF button.

5. Remove 15A fuse from control board.

After Servicing Generator

Always perform the following steps AFTER servicing

generator:

1. Reinstall 15A fuse in control board.

2. Press and hold the control board AUTO button.

3. Set generator’s circuit breaker to its ON position.

4. Close and secure roof with keys.

5. Open manual fuel shut-off valve.

Service Code Detection System

The generator may have to run for long periods of time

with no operator present. For that reason, the system is

equipped with sensors that automatically shut down the

generator in the event of potentially damaging conditions,

such as low oil pressure, high temperature, overspeed, or

other conditions.

CAUTION

Auto start of Machinery - Installing the

15 Amp fuse could cause the engine to crank

and start at any time without warning resulting in

minor to moderate injury.

• Do remove the 15A fuse before maintaining

and/or servicing generator.

DO NOT

• Do not reinstall 15A fuse until after

maintaining and/or servicing generator

MAINTENANCE

NOTICE

Contact a skilled person for service code repairs/

maintenance

Not for

Reproduction

The generator’s control board displays service codes. The

service code descriptions are listed below:

Low Battery Voltage: This condition occurs if the battery

voltage drops below the preset value. This condition may

be caused by a faulty battery or battery charge circuit. See

Battery Charge Circuit.

Under Voltage: This condition occurs if the generator

output voltage is less than the preset value. This condition

may be caused by a restriction in the fuel ow, the electronic

governing system not functioning properly, a broken or

disconnected signal lead, a failed alternator winding, the

control board circuit breaker is open or the generator is

overloaded.

Over Voltage: This feature protects devices connected to

the transfer switch by shutting the generator down if the

generator output voltage is greater than the preset value.

This condition may be caused by a failed voltage regulator,

alternator excitation circuit or a load imbalance.

Low Oil Pressure: The unit is equipped with an oil

pressure switch that uses normally closed contacts held

open by engine oil pressure during operation. The switch

contacts will close and the engine will shut down if oil

pressure drops below the rated value. This condition may

be caused by low oil volume.

Engine Does Not Start: This feature prevents the

generator from damaging itself if it continually attempts to

start despite another problem, such as no fuel supply. Each

time the system is directed to start, the unit will crank for 10

seconds, pause for 10 seconds, and repeat. If the system

does not begin producing electricity after approximately 2

minutes, the unit will stop cranking. The most likely cause

of this problem is no fuel supply or incorrect fuel selector

setting.

Generator Sense Fault: This fault will occur if the

generator is in the o state and the control panel measures

a signal from the generator output.

Low Frequency: This feature protects devices connected

to the transfer switch by shutting the generator down if the

engine runs slower than 45 Hz for 3 seconds. This condition

may be caused by a failed engine component, electronic

governor system, or excessive loads on the generator.

Engine Overspeed: This feature protects devices

connected to the transfer switch by shutting the generator

down if the engine runs faster than 55Hz for 3 seconds. This

condition may be caused by a problem within the electronic

governor system.

High Oil Temperature: The unit is equipped with an oil

temperature switch that uses normally open contacts. The

contacts will close and the engine will shut down if the

temperature exceeds the rated value. This condition may be

caused by running the generator with the panels removed,

the roof open, an obstructed air inlet or exhaust port, or

debris in the engine compartment.

Transfer Switch Service Code (if equipped): This feature

senses an open condition in the transfer switch circuitry.

This condition may be caused by a blown fuse in the

transfer switch.

Battery Charge Circuit: This feature senses an open

condition in the battery charge circuitry. This condition may

be caused by a blown fuse in the control panel.

Reset Service Code Detection System

The service code detection system must be reset each time

it activates. Contact a skilled person for technical problems

associated with Service Code Detection System.

To reset code detection system:

1. Open roof of generator.

2. Set generator’s circuit breaker to its OFF position.

3. Remove 15A fuse from control board. Wait 30 seconds.

Reinstall fuse.

4. Press and hold the control board AUTO button. Wait

30 seconds to allow generator to start as conditions

warrant.

5. Set generator’s circuit breaker to its ON position.

6. Close and secure roof with keys.

MAINTENANCE cont.

Not for

Reproduction

Maintenance Schedules

Regular maintenance will improve the performance and

extend the life of the generator.

Follow hourly or calendar intervals of operation, whichever

occurs first.

Contact a skilled person to perform maintenance per the

maintenance schedule for skilled person. Failure to comply

will void warranty on generator.

MAINTENANCE cont.

Maintenance

Every 8

running

hours

Every 6

months

Maintain Carbon Monoxide Detectors



Maintain Smoke Detectors



Clean Generator



Maintenance

Every 8

running

hours

Every 100

running

hours

Annually

Every 100

running

hours

or annually

Every 500

running

hours

or annually

Check Engine Oil Level



Change Air Filter



Change Engine and Oil Filter



Replace Spark Plugs



Inspect Valve Clearance



Service Battery



Inspect Fuel System



Inspect Circuit Breaker Torques



Maintenance Schedule for User

Maintenance Schedule for Skilled Person

Not for

Reproduction

MAINTENANCE cont.

Generator Maintenance for User

User generator maintenance instructions are listed below.

The generator’s warranty does not cover items that have

been subjected to user abuse or negligence. To receive full

value from warranty, the user must maintain the generator

as instructed in this manual.

Maintain Carbon Monoxide Detectors

Carbon monoxide detectors are required per

manufacturer’s recommendations/instructions.

User must maintain carbon monoxide detectors.

Maintain Smoke Detectors

Smoke detectors are required per manufacturer’s

recommendations/instructions. User must maintain smoke

detectors.

Clean Generator

Clean in and around the generator every 8 running hours.

Clean generator as follows:

1. Close manual fuel shut-off valve.

2. Open roof of generator.

3. Set generator’s circuit breaker to its OFF position.

4. Press and hold the control board OFF button.

5. Remove 15A fuse from control board.

6. Use a damp cloth to wipe exterior surfaces clean.

7. Use a soft bristle brush and vacuum cleaner to remove

dirt or debris.

8. Use low pressure air (not to exceed 172 kPa) to blow

away dirt or debris.

9. Ensure that the enclosure inlets and exhaust outlets are

clear of obstructions, such as leaves or snow. This will

prevent generator damage caused by overheating.

10. Reinstall 15A fuse in control board.

11. Press and hold the control board AUTO button.

12. Set generator’s circuit breaker to its ON position.

13. Close and secure roof with keys.

14. Open manual shut-off valve.

NOTICE

DO NOT use direct spray from a garden

hose to clean generator

CAUTION

Auto start of Machinery - Installing the

15 Amp fuse could cause the engine to crank

and start at any time without warning resulting in

minor to moderate injury.

• Do remove the 15A fuse before maintaining

and/or servicing generator.

DO NOT

• Do not reinstall 15A fuse until after

maintaining and/or servicing generator

Not for

Reproduction

TROUBLESHOOTING

Troubleshooting for User

The troubleshooting guide below is specically targeted for

the user.

Problem Cause Correction

Engine is running, but no generator output

voltage.

1. Circuit breaker open.

2. Poor wiring connections.

1. Reset circuit breaker.

2. Contact a skilled person.

Engine runs well at no-load but “bogs down”

when loads are connected.

1. Generator is overloaded.

2. Short circuit in a connected load.

3. Shorted generator circuit.

4. Fuel pressure is incorrect.

1. Remove one or more loads.

2. If safe to do so, disconnect shorted electrical load or

contact a skilled person.

3. Contact a skilled person.

4. Contact a skilled person.

Engine will not start; or starts and runs

rough.

1. 15A fuse missing or blown.

2. Fuel supply turned o or depleted.

3. Incorrect fuel selector.

4. Failed battery.

1. Install new 15A fuse in control board.

2. Open fuel valves; check propane tank.

3. Contact a skilled person.

4. Contact a skilled person.

Engine shuts down during operation.

1. Fuel supply turned o or depleted.

2. Service code detected by control

board.

1. Check fuel valves; check propane tank.

2. Refer to Service Code Detection System

section in this manual and contact a skilled person.

Generator will not exercise.

1. Control board not set to AUTO.

2. Exercise timer not set.

3. Generator date and time not set.

4. Failed battery.

5. 15A fuse missing or blown.

1. Press AUTO button on control board.

2. Set exercise timer. See General Set-up Screen

section in this manual.

3. Set date and time. See General Set-up Screen

section in this manual.

4. Contact a skilled person.

5. Install new 15A fuse in control board.

Excessive Vibration

1. Failed cylinder on engine. 1. Contact a skilled person.

Odor of fuel

1. Fuel leak. 1. Close manual fuel shut o valve and contact a

skilled person.

Utility power returns, unit does not stop

1. Blown fuses in transfer switch.

2. 5 minute minimum runtime not

lapsed.

1. Contact a skilled person.

2. Wait 5 minutes. See Engine Cool-Down Timer

section in this manual.

Contact a skilled person to perform troubleshooting/

maintenance per the guide. Failure to comply will void

warranty on generator.

Not for

Reproduction

EQUIPMENT SPECIFICATIONS

GENERATOR SPECIFICATIONS

Rated Power 8kVA

Rated Maximum Load Current

(at 25�C LP)* at 230 Volts 34.8 Amps

Rated AC Voltage 230 Volts

Phase Single Phase

Rated Frequency 50 Hertz

Generator Breaker 40 Amp

Normal Operating Range -28.8�C to 40�C

Output Sound Power 97 dB(A) L

Shipping Weight 139 kg

*Natural gas rating will depend on specific fuel but typical derates are

between 10 to 20% off the LP gas rating.

ENGINE SPECIFICATIONS

Displacement 570 cc

Bore 72 mm

Stroke 70 mm

COMMON SERVICE PARTS

Fuse - ATO Type 15A 198573GS

Read the illustrated parts list for service parts.

Not for

Reproduction

Not for

Reproduction

Page is loading ...

Simplicity HGS, 8000 SERIES 50HZ User manual

Brand: Simplicity

Model: HGS, 8000 SERIES 50HZ

Category: Power generators

Type: User manual

This manual is also suitable for

040496-01

Download PDF

report

in other languages

polski: Simplicity HGS, 8000 SERIES 50HZ Instrukcja obsługi

Simplicity HGS, 8000 SERIES 50HZ User manual

This manual is also suitable for

Simplicity HGS, 8000 SERIES 50HZ User manual

in other languages

Related papers

Other documents