Troy Built 1904 User manual

Brand: Troy Built

Model: 1904

Category: High-pressure cleaners

Type: User manual

Owner’s Manual / Manual del Propietario

Questions? Preguntas?

Helpline - 1-888-611-6708 M-F 8-5 CT

Manual No. 194245GS Revision 2 (04/16/2004)

Pressure Washer / Lavadora de Presión

Model / Modelo 020200

Printed in USA

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON,WISCONSIN, U.S.A.

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

IMPORTANTE: LEYO LA SEGURIDAD LAS ORDENES Y LAS INSTRUCCIONES DETENIDAMENTE

Troy-Bilt® is a registered trademark of Troy-Bilt, LLC and is used under license to Briggs & Stratton Power Products.

Troy-Bilt® es una marca registrada de Troy-Bilt, LLC y se usa abajo licencia a Briggs & Stratton Power Products.

TABLE OF CONTENTS

Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Know Your Pressure Washer. . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-15

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Last Page

EQUIPMENT

DESCRIPTION

Read this manual carefully and become familiar

with your pressure washer. Know its

applications, its limitations and any hazards

involved.

This manual contains information for a high pressure

washer that operates at 2,700 PSI at a flow rate of

2.5 gallons per minute.This powerful, high quality system

features large 10” wheels, a pump equipped with an

automatic cool down system, chemical injection system,

nozzle extension with quick connect nozzles, safety goggles,

heavy duty 25’ hose, and more.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter or otherwise improve the

product and this document at any time without prior

notice.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury

hazards. Obey all safety messages that follow

this symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or serious

injury. WARNING indicates a hazard which, if not

avoided, could result in death or serious injury. CAUTION

indicates a hazard which, if not avoided, might result in

minor or moderate injury. CAUTION, when used

without the alert symbol, indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of injury or death.

Hazard Symbols and Meanings

In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

Safety Rules

Section

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface

Fall

Kickback

Flying Objects

Fluid Injection

Section 1: Safety Rules

• Keep water spray away from electric wiring or fatal electric

shock may result.

Spray contact with electrical wiring can result in

electrocution.

WARNING

• Operate pressure washer ONLY outdoors.

• Use a respirator or mask whenever there is a chance that

vapors may be inhaled.

• Read all instructions with mask so you are certain the mask will

provide the necessary protection against inhaling harmful vapors.

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea,

fainting or poisoning.

Breathing carbon monoxide will cause nausea,

fainting or death.

DANGER

• Keep spray nozzle between 8 to 24 inches away from cleaning

surface.

• Operate this unit on a stable surface.

• The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding or any other relatively unstable location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun kicks back.

Use of pressure washer can create puddles and

slippery surfaces.

High pressure spray could cause you to fall if

you are too close to the cleaning surface.

WARNING

WHEN ADDING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing gas cap.

• Fill fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel

to spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• NEVER aim spray gun at people, animals or plants.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS RELIEVE water pressure each time engine is stopped

by squeezing trigger on spray gun.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury and

possible amputation.

WARNING

Section 1: Safety Rules

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

Excessively high or low operating speeds increase risk

of injury and damage to pressure washer.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect spark plug wire from spark plug and place wire

where it cannot contact spark plug.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT point spray gun at glass when in jet spray mode.

• NEVER aim spray gun at plants.

High pressure spray may damage fragile items including

glass.

CAUTION

• DO NOT wear loose clothing, jewelry or anything that may

be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

Starter and other rotating parts can entangle

hands, hair, clothing, or accessories.

WARNING

• Always wear eye protection when using this equipment or in

vicinity of where equipment is in use.

High pressure spray can cause paint chips or

other particles to become airborne.

WARNING

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is

running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

A pressure washer produces a high pressure spray

which increases risk of injury and damage to unit.

CAUTION

• If you have questions about intended use, ask dealer or

contact Briggs & Stratton Power Products.

• NEVER operate units with broken or missing parts, or

without protective housing or covers.

• DO NOT by–pass any safety device on this machine.

• Before starting pressure washer in cold weather, check all

parts of the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on high pressure hose. Use

handle provided on unit.

• Check fuel system for leaks or signs of deterioration, such as

chafed or spongy hose, loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure

washer.

• This equipment is designed to be used with Briggs & Stratton

Power Products authorized parts ONLY. If equipment is used

with parts that DO NOT comply with minimum specifications,

user assumes all risks and liabilities.

Improper treatment of pressure washer can damage it

and shorten its life.

CAUTION

• DO NOT touch hot surfaces.

• Stay clear of exhaust gases.

• Allow equipment to cool before touching.

Running engines produce heat and hot exhaust

gases.Temperature of muffler and nearby areas

can reach or exceed 150°F (65°C).

Fire or severe burns can occur.

WARNING

KNOW YOUR PRESSURE WASHER

Read this owner’s manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

Chemical Injection

Siphon/Filter

Spray Gun

Nozzle Extension

with Quick Connect

Throttle Lever

Choke Lever

Fuel Valve

Recoil Starter

(on front of engine)

Air Filter

Fuel Tank

Pump equipped

with Automatic

Cool Down System

Water Inlet

Oil Fill Cap

Spray Tips

High Pressure Outlet

Accessory Tray — Provides convenient storage for

standard and optional accessories, such as brushes, turbo

wands, ect.

Air Filter — Protects engine by filtering dust and debris out

of intake air.

Automatic Cool Down System — Cycles water through

pump when water reaches 125°-155°F.Warm water will

discharge from pump onto ground.This system prevents

internal pump damage.

Chemical Injection Siphon/Filter — Use to siphon

detergent or other pressure washer chemicals into the low

pressure stream.

Choke Lever — Prepares a cold engine for starting.

Data Tag — Provides model, revision and serial number of

pressure washer. Please have these readily available if calling

for assistance.

Fuel Tank — Fill tank with regular unleaded fuel.Always leave

room for fuel expansion.

Fuel Valve — Used to turn fuel on and off to engine.

High Pressure Hose — Connect one end to the water

pump and the other end to the spray gun.

High Pressure Outlet — To connect high pressure hose.

Nozzle Extension with Quick Connect — Allows you to

switch between four different spray tips.

Oil Fill Cap — Fill engine with oil here.

Pump — Develops high pressure.

Recoil Starter — Use for starting the engine manually.

Safety Goggles (not shown) — Always use the enclosed

goggles or other eye protection when running your

pressure washer.

Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes safety latch.

Spray Tips — Chemical injection, 0°, 15°, and 40°: for various

high pressure cleaning applications.

Throttle Lever—Sets engine in starting mode for recoil

starter and stops a running engine.

Water Inlet — Connect garden hose here.

Accessory Tray

Features and Controls

Section

Data Tag

High Pressure

Hose

ASSEMBLY

IMPORTANT: Read entire owner’s manual before you

attempt to assemble or operate your new pressure washer.

Remove Pressure Washer From

Carton

1. Remove parts bag packed with pressure washer.

2. Slice two corners at end of carton from top to bottom

so panel can be folded down flat, then remove all

packing material.

3. Roll pressure washer out of carton.

Carton Contents

Items in the carton include:

• Main Unit

• Safety Goggles

• Handle

• Plastic Accessory Tray

• High Pressure Hose

• Spray Gun

• Nozzle Extension with Quick Connect Fitting

• Oil Bottle

• Parts Bag (which includes the following):

• Owner’s Manual

• Engine Manual

• Owner’s Registration Card

• Bag containing 4 multi–colored Quick Connect Spray

Tips

• Handle Fastening Hardware Kit (which includes):

• Carriage Bolt

• “L” Bolt

• Plastic Knobs (2)

• “J” Hook

• Chemical Hose Clip

• Self Tapping Screws (4)

PREPARING PRESSURE

WASHER FOR USE

If you have any problems with the assembly of your

pressure washer or if parts are missing or damaged, call the

pressure washer helpline at 1-888-611-6708.

To prepare your pressure washer for operation, you

will need to perform these tasks:

1. Fill out and send in registration card.

2. Attach accessory tray to handle, then attach handle to

main unit.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect high pressure hose to spray gun and pump.

6. Connect water supply to pump.

7. Attach nozzle extension to spray gun.

8. Select/attach quick connect spray tip to nozzle

extension.

Attach Handle and Accessory Tray

NOTE: All assembly operations given in this section will be

described from the perspective of assembling the pressure

washer from the rear.

1. Slide plastic accessory tray onto handle and align holes

in accessory tray with holes on handle (Figure 1).

Figure 1 — Attach Accessory Tray

Section

Assembly

• #2 Phillips Screwdriver

Required Assembly Tools

2. Secure tray to handle with self tapping screws using a

#2 phillips screwdriver. Ensure screws are tight but not

crushing the plastic accessory tray.

3. Place handle assembly onto handle supports connected

to main unit. Make sure holes in handle align with holes

on handle supports (Figure 2).

NOTE: It may be necessary to move the handle supports

from side to side in order to align the handle so it will slide

over the handle supports.

4. Insert “L” bolt through hole on right side of handle

(viewing from handle side of unit) and attach plastic

knob.Tighten knob by hand (Figure 3).

5. Insert carriage bolt through left side hole from outside

of unit and attach a plastic knob from inside of unit

(viewing unit from the handle side).Tighten by hand

(Figure 3).

6. Insert “J” hook into second from left slot in accessory

tray (Figure 4).

7. Pinch chemical hose and slide it into metal clip as

shown in Figure 5.

8. Tilt unit up by handle and attach metal clip to rib on

center underside of accessory tray (Figure 6). Slide

chemical hose through metal clip so that it is tight but

not kinked.

Add Engine Oil and Fuel

• Place pressure washer on a level surface.

• Refer to engine owner’s manual and follow oil and fuel

recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to

engine owner’s manual for recommendations.

Figure 4 — Install “J” Hook on Accessory Tray

Figure 5 — Slide Chemical Hose into Metal Clip

Figure 6 — Slide Metal Clip onto Accessory Tray Flange

Align Holes

Handle

Supports

Figure 2 — Attach Handle to Base

Figure 3 — Secure Handle

Section 3: Assembly

CAUTION

• Refer to engine manual for oil and fuel fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Any attempt to crank or start the engine before it has

been properly filled with the recommended oil will result

in equipment failure.

Connect Hose and Water Supply to

Pump

IMPORTANT: To avoid pump damage, you must assemble

the nozzle extension to the spray gun and attach all hoses

before you start the engine.

1. Attach one end of high pressure hose to high pressure

outlet on pump (Figure 7).Tighten by hand.

2. Attach other end of hose to base of spray gun

(Figure 8).Tighten by hand.

3. Before connecting garden hose to water inlet, inspect

inlet screen (Figure 9). Clean screen if it contains

debris, replace if damaged. DO NOT RUN PRESSURE

WASHER IF SCREEN IS DAMAGED.

4. Run water through garden hose for 30 seconds to

clean out any debris.Turn off water.

IMPORTANT: DO NOT siphon standing water for the

water supply. Use ONLY cold water (less than 100°F).

5. Connect garden hose (not to exceed 50 feet in length)

to water inlet.Tighten by hand (Figure 9).

6. Turn ON water and squeeze trigger on spray gun to

purge pump system of air and impurities.

Checklist Before Starting Engine

Review the unit’s assembly to confirm you have performed

all of the following:

1. Make sure handle is in place and secure.

2. Check that oil has been added to the proper level in

engine crankcase.

3. Add proper fuel to fuel tank.

4. Check for properly attached hose connections.

5. Check to make sure that there are no kinks, cuts, or

damage to high pressure hose.

6. Provide a proper water supply at an adequate flow.

7. Be sure to read “Safety Rules” and “How To Use Your

Pressure Washer” before using pressure washer.

Section 3: Assembly

CAUTION

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

There MUST be at least ten feet of unrestricted garden

hose between the pressure washer inlet and any flow

shut off device, such as a ‘Y’ shut-off connector or other

convenience-type water shut-off valve.

• Always wear eye protection when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate eye protection.

High pressure spray can cause paint chips or

other particles to become airborne.

WARNING

Connect high

pressure hose

here

Figure 8 — Connect High Pressure Hose to Spray Gun

Figure 7 — Connect High Pressure Hose to Pump

Figure 9 — Connect Garden Hose to Water Inlet

Inspect inlet

screen, DO

NOT use if

damaged, clean

if dirty.

HOW TO USE YOUR

PRESSURE WASHER

If you have any problems operating your pressure washer,

please call the pressure washer helpline at 1-888-611-6708.

To Start Pressure Washer

To start your pressure washer for the first time, follow

these instructions step-by-step.This starting information

also applies if you have let the pressure washer sit idle for

at least a day.

1. Place pressure washer near an outside water source

capable of supplying water at a flow rate greater than

3.5 gallons per minute and no less than 20 PSI at

pressure washer end of garden hose.

2. Check that high pressure hose is connected to spray

gun and to pump. See “Preparing Pressure Washer for

Use” for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure

washer pump. Turn ON water.

5. Squeeze trigger on gun until you have a steady stream

of water.This purges pump of air and impurities.

6. Attach nozzle extension to spray gun (Figure 10).

Tighten by hand.

7. Place colored quick connect spray tips in slots on

holder that’s attached to nozzle extension (Figure 11).

8. Choose spray tip you want to use and insert it into

nozzle extension. See “How to Use Spray Tips” on

page 11.

9. Engage safety latch to spray gun trigger (Figure 12).

10. Move variable pressure control lever to “High”

position, shown on engine as a rabbit (Figure 13).

Figure 10 — Connect Nozzle Extension to Spray Gun

Figure 13 - Variable Pressure Control Lever

Section

Operation

CAUTION

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

DO NOT run the pump without the water supply

connected and turned on.

Figure 11 — Install Spray Tips in Holder

Safety Latch

Figure 12 — Spray Gun with Safety Latch Engaged

11. Start engine according to instructions given in engine

owner’s manual.Also see operating instructions tag

located on the pressure washer.

How to Stop Your Pressure Washer

• Move variable pressure control lever to “Stop” position.

• Turn engine off according to instructions given in the

engine owner’s manual.

• Squeeze trigger on the spray gun to relieve

pressure in the hose.

NOTE: A small amount of water will squirt out when you

release the pressure.

How to Use Accessory Tray

The unit is equipped with an accessory tray with places to

store your nozzle extension , and slots to hold the cleaning

solution bottle and the detergent siphoning filter.There are

also two hooks at the ends of the handle to hold your

spray gun and high pressure hose.

NOTE: The extra holes in the tray are for storing a brush

and a turbo wand.The brush and turbo wand are NOT

included with your pressure washer.You can buy these

items as optional accessories.

1. Place nozzle extension through hole on accessory tray,

as shown in Figure 14.

2. Hang chemical solution bottle on “J” hook and place

detergent siphoning filter in last slot on left (Figure 14).

3. Place spray gun on hook attached to accessory tray on

right side of unit (Figure 14).

4. Hang high pressure hose on hook attached to

accessory tray on left side of unit as shown on page 5.

Figure 14 — Typical Accessory Tray

Section 4: Operation

CAUTION

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• If engine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze trigger

on spray gun.

Avoid injury from kickback.

How to Use Spray Tips

The quick–connect on the nozzle extension allows you to

switch between four different spray tips.The spray tips vary

the spray pattern as shown below (Figure 15).

Follow these instructions to change spray tips:

1. Engage safety latch on spray gun.

2. Pull back collar on quick–connect and pull current

spray tip off. Store spray tips in space provided on

handles storage panel.

3. Select desired spray tip:

• For gentle rinse, select white 40° spray tip.

• To scour surface, select yellow 15° or red 0° spray

tip.

• To apply chemical, select black spray tip.

4. Pull back on collar, insert new spray tip and release

collar.Tug on spray tip to make sure it is securely in

place.

5. For most effective cleaning, keep spray tip from 8 to

24 inches away from cleaning surface. If you get spray

tip too close, you may damage cleaning surface. DO

NOT get closer than 6 inches when cleaning tires.

Cleaning and Applying Chemical

IMPORTANT: Use soaps designed specifically for

pressure washers. Household detergents could damage

the pump.

To apply detergent follow these steps:

1. Review spray tip use.

2. Prepare detergent solution as required by

manufacturer.

3. Hang detergent solution on “J” hook attached to

accessory tray, as shown in Figure 16.

4. Place small filter end of detergent siphoning tube into

detergent container.

Figure 16 — Insert Filter into Container

Section 4: Operation

• NEVER exchange spray tips without locking the safety latch

on the trigger.

A pressure washer produces a high pressure spray

which increases risk of injury and damage to unit.

CAUTION

• Starting the engine without all the hoses connected and

without the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

You must attach all hoses before you start the engine.

40° White 15° Yellow 0° Red

Black

Use to apply

chemical

Figure 15 — Spray Tip Spray Patterns

Low Pressure

High Pressure

CAUTION

• When inserting the filter into a detergent solution bottle,

route the tube so as to keep it from inadvertently contacting

the hot muffler.

Keep the chemical injection tube from coming in contact

with the hot muffler.

5. Make sure black spray tip is installed.

NOTE: Detergent cannot be applied with the high

pressure spray tips (White, Green,Yellow, or Red).

6. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun and pump and start engine.

7. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward, using

long, even, overlapping strokes.

8. Allow detergent to soak in between 3–5 minutes

before washing and rinsing. Reapply as needed to

prevent surface from drying. DO NOT allow detergent

to dry on (prevents streaking).

IMPORTANT:You must flush the chemical injection

system after each use by placing the filter into a bucket of

clean water, then run the pressure washer in low pressure

for 1-2 minutes.

Pressure Washer Rinsing

Wash and Rinse Surface

This pressure washer permits regulation of output water

pressure by varying the engine speed.The variable pressure

control lever found on the front of the engine may be set,

as shown in Figure 17:

After you have applied detergent, scour the surface

and rinse it clean as follows:

1. Apply safety latch to spray gun.

2. Remove black chemical nozzle from nozzle extension.

3. Select and install desired high pressure nozzle

following instructions “How to Use Spray Tips” on

page 11.

4. Keep spray gun a safe distance from the area you plan

to spray.

5. Adjust spray pressure by sliding variable pressure contol

lever left or right, as shown in Figure 13 on page 9.

6. Apply a high pressure spray to a small area and then

check the surface for damage. If no damage is found,

you can assume it is okay to continue rinsing.

7. Start at top of area to be rinsed, working down with

same overlapping strokes as you used for cleaning.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reach temperatures

above 125°F.The system engages to cool the pump by

discharging the warm water onto the ground.

Pressure

Low

High

Duty

Light

Medium

Heavy

Application

Auto

Concrete

Paint removal

Boat

Driveway

Degreasing

Furniture

Deck

Figure 17 - Variable Pressure Control

Section 4: Operation

• Keep spray nozzle between 8 to 24 inches away from cleaning

surface.

• Operate this unit on a stable surface.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding or any other relatively unstable location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun kicks back.

High pressure spray could cause you to fall if

you are too close to the cleaning surface.

WARNING

GENERAL MAINTENANCE

RECOMMENDATIONS

The pressure washer warranty does not cover items that have

been subjected to operator abuse or negligence.To receive full

value from the warranty, the operator must maintain the

pressure washer as instructed in this manual.

• Some adjustments will need to be made periodically to

properly maintain your pressure washer. Check the spray

gun and adjustable nozzle extension assembly for wear.

• All maintenance in this manual and the engine owner’s

manual should be made at least once each season.

• Once a year you should clean or replace the spark plug,

clean or replace the air filter.A new spark plug and clean

air filter assure proper fuel-air mixture and help your

engine run better and last longer. Please refer to your

engine owner’s manual for more details.

• If equipped with inflatable tires, keep the air pressure at

the value marked on the tire or within 15 and 40 psi.

Before Each Use

1. Check engine oil level.

2. Check water inlet screen for damage.

3. Check in-line filter for damage.

4. Check high pressure hose for leaks.

5. Check detergent siphoning tube and filter for damage.

6. Check spray gun and nozzle extension assembly for leaks.

7. Rinse out garden hose to flush out debris before

connecting to pressure washer.

PRESSURE WASHER

MAINTENANCE

Check and Clean Inlet Screen

Examine the screen on the water inlet. Clean it if the

screen is clogged or replace it if screen is damaged.

Check High Pressure Hose

The high pressure hose can develop leaks from wear,

kinking, or abuse. Inspect the hose each time before using

it. Check for cuts, leaks, abrasions or bulging of cover,

damage or movement of couplings. If any of these

conditions exist, replace the hose immediately.

Check Detergent Siphoning Tube

Examine the filter on the detergent tube and clean if

clogged.The tube should fit tightly on the barbed fitting.

Examine the tube for leaks or tears. Replace the filter or

tube if either is damaged.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it

with clean water before stopping the engine.

1. Place chemical injection siphon/filter in a bucket full of

clean water.

2. Attach black low pressure spray tip.

3. Flush for 1-2 minutes.

4. Shut off engine.

IMPORTANT: Simply shutting OFF engine will not

release pressure in the system. When the engine has

shut down, squeeze the trigger on the spray gun to

relieve the pressure in the hose.

Check Gun and Nozzle Extension

Examine the hose connection to the spray gun and make

sure it is secure.Test the trigger by pressing it and making

sure it “springs back” into place when you release it. Put

the safety latch in the ON position and test the trigger.You

should not be able to press the trigger.

Check In-Line Filter

Refer to Figure 18 and service the in-line filter if it

becomes clogged, as follows:

1. Detach spray gun and nozzle extension from high

pressure hose. Detach nozzle extension from spray gun

and remove o-ring and screen from nozzle extension.

Nozzle Extension

Filter Screen

O-ring

Figure 18 — Clean In-Line Filter

Maintenance

Section

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST exceed maximum pressure

rating of unit.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury and

possible amputation.

WARNING

Flush screen, spray gun, and nozzle extension with

clean water to clear debris.

2. Place in-line filter screen into threaded end of nozzle

extension. Direction does not matter. Push screen in

with eraser end of pencil until it rests flat at bottom of

opening.Take care to not bend the screen.

3. Place o-ring into recess. Push o-ring snugly against

in-line filter screen.

4. Assemble nozzle extension to spray gun, as described

earlier in manual.

Purge Pump of Air and

Contaminants

To remove air from the pump, follow these steps:

1. Set up pressure washer as described in “Preparing

Pressure Washer For Use”. Connect water supply and

turn water on.

2. Pull trigger on spray gun and hold.

3. When water supply is steady and constant, engage

safety latch.

To remove contaminants from the pump, follow

these steps:

1. Set up pressure washer as described in “Preparing

Pressure Washer For Use”. Connect water supply and

turn water on.

2. Start engine according to instructions in “To Start

Pressure Washer”.

3. Remove nozzle extension from spray gun.

4. Squeeze trigger on the spray gun and hold.

5. When water supply is steady and constant, engage

safety latch and reattach nozzle extension.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure.The

principal cause of excessive pump pressure is a spray tip

clogged or restricted with foreign materials, such as dirt,

etc.To correct the problem, immediately clean the spray tip

following these instructions:

1. Shut off engine and turn off water supply.

2. Remove spray tip from end of nozzle extension.

3. Remove in-line filter from other end of nozzle

extension.

4. Use a small paper clip to free any foreign material

clogging or restricting spray tip (Figure 19).

5. Using a garden hose, remove additional debris by back

flushing water through nozzle extension (Figure 20).

Back flush between 30 to 60 seconds.

6. Reinstall spray tip and in-line filter into nozzle

extension.

7. Reconnect nozzle extension to spray gun.

8. Reconnect water supply, turn on water, and start

engine.

9. Test pressure washer by operating with each Quick

Connect spray tip.

O–Ring Maintenance

Purchase an O–Ring/Maintenance Kit, part number

191922GS by contacting the nearest authorized service

center. It is not included with the pressure washer.This kit

includes replacement o-rings, rubber washer and water

inlet filter. Refer to the instruction sheet provided in the kit

to service your unit’s o-rings.

Use wire here

to remove

debris.

Figure 19 — Nozzle Maintenance

Figure 20 — Backflushing the Nozzle Extension

Section 5: Maintenance

Pump Maintenance

Changing Pump Oil

Change oil every 50 hours or once yearly, whichever

occurs first.

NOTE: You must purchase a premeasured bottle of pump

oil, item number 190585GS, by contacting the nearest

authorized service center.

Change pump oil as follows:

1. Drain engine oil and fuel from pressure washer.

2. Use a 8mm allen wrench to remove black pump oil cap

between high pressure outlet and garden hose inlet

(Figure 21).

3. Tilt pressure washer to drain oil into an approved

container until it drips slowly from pump.

4. Tilt pressure washer in opposite direction and empty

premeasured pump oil bottle into same opening (a

small funnel may be helpful).

5. Install black pump oil cap and tighten firmly.

6. Set pressure washer in upright position.Add fuel and

engine oil.

ENGINE MAINTENANCE

See the engine owner’s manual for instructions on how to

properly maintain the engine.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Data Tag

Data tag information is very important if you need help from

our Customer Service Department or an authorized service

dealer.

• The data tag (Figure 22) is located on the base of the

pressure washer. For future reference, please copy the

model, revision, and serial number of the pressure washer

in the space below.

Section 5: Maintenance

Figure 22 — Data Tag

Copy Model

Number Here

Copy Revision

Here

Copy Serial

Number Here

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Avoid prolonged or repeated skin contact with used

motor oil.

CAUTION

Oil Cap

Figure 21 - Changing Pump Oil

PREPARING THE UNIT

FOR STORAGE

Water should not remain in the unit for long periods of

time. Sediments or minerals can deposit on pump parts and

“freeze” pump action. If you do not plan to use the pressure

washer for more than 30 days, follow this procedure:

1. Flush detergent siphoning tube by placing the filter into

a pail of clean water while running pressure washer in

low pressure mode. Flush for one to two minutes.

2. Shut off the engine and let it cool, then remove high

pressure and garden hoses. Disconnect spark plug wire

from spark plug.

3. Empty the pump of liquids by pulling the engine recoil

handle about 6 times.This should remove most of the

liquid in the pump.

4. Use pump saver to prevent corrosion build up and

freezing of pump.

5. Store unit in a clean, dry area.

Protecting the Pump

To protect the pump from damage caused by mineral

deposits or freezing, use PumpSaver to treat pump.This

prevents freeze damage and lubricates pistons and seals.

NOTE: PumpSaver is available as an optional accessory. It

is not included with the pressure washer. Contact the

nearest authorized service center to purchase PumpSaver.

To use PumpSaver, make sure the pressure washer is

turned off and disconnected from supply water. Read and

follow all instructions and warnings given on the PumpSaver

container.

NOTE: PumpSaver will drip from pump after treatment

and will stain wood and concrete.

NOTE: If PumpSaver is not available, draw RV antifreeze

(non-alcohol) into the pump by pouring the solution into a

3-foot section of garden hose connected to inlet adapter

and pulling recoil handle twice.

STORING THE ENGINE

See the engine owner’s manual for instructions on how to

properly prepare the engine for storage.

Storage

Section

CAUTION

• Failure to do so will permanently damage your pump and

render your unit inoperable.

• Freeze damage is not covered under warranty.

You must protect your unit from freezing temperatures.

• Always wear eye protection when using PumpSaver.

Read and follow all cautions and warnings on the

PumpSaver can label.

CAUTION

TROUBLESHOOTING

Troubleshooting

Section

Problem Cause Correction

Pump has following problems:

failure to produce pressure,

erratic pressure, chattering, loss

of pressure, low water volume.

1. Low pressure spray tip installed.

2. Water inlet is blocked.

3. Inadequate water supply.

4. Inlet hose is kinked or leaking.

5. Clogged inlet hose strainer.

6. Water supply is over 100°F.

7. High pressure hose is blocked or

leaks.

8. Gun leaks.

9. Spray tip is obstructed.

10. Pump is faulty.

1. Replace spray tip with high

pressure spray tip.

2. Clear inlet.

3. Provide adequate water flow.

4. Straighten inlet hose, patch leak.

5. Check and clean inlet hose

strainer.

6. Provide cooler water supply.

7. Clear blocks in outlet hose.

8. Replace gun.

9. Clean spray tip.

10. Contact Authorized service facility.

Detergent fails to mix with spray.

1. Detergent siphoning tube is not

submerged.

2. Chemical filter is clogged or

cracked.

3. Dirty in-line filter.

4. High pressure spray tip installed.

1. Insert detergent siphoning tube

into detergent.

2. Clean or replace filter/detergent

siphoning tube.

3. See "Check In-Line Filter".

4. Replace spray tip with low

pressure spray tip.

Engine shuts down during

operation.

Out of gasoline. Fill fuel tank.

Item Part # Description

1 B190156GS BASE

2 B187602GS HANDLE

3 187606GS BILLBOARD

4 185877GS HOSE

5 192134GS KIT, Engine Mounting Hardware

6 192131GS KIT, Pump Mounting Hardware

7 194062GS PUSHNUT

8 B5646GS KIT, Spray Tips

9 192199GS EXTENSION

Item Part # Description

10 B1862GS GUN

11 190668GS KIT, Handle Fasteners

12 192553GS KIT,Vibration Mount

13 192526GS KIT,Wheel

14 23139DGS KEY

15 194106GS ASSY, Pump (see page 19)

16 194298GS VALVE,Thermal Relief

900 NSP ENGINE

EXPLODED VIEW AND PARTS LIST — UNIT

Section

Exploded Views and Parts Lists

Items Not Illustrated:

Part # Description

194245GS MANUAL, Owner’s

MS6737 MANUAL, Engine

194342GS KIT, Decals

BB3061BGS OIL, Engine

Section 8: Exploded Views and Parts Lists

EXPLODED VIEW AND PARTS LIST — PUMP

Item Part # Description

19 190571GS CAP, Oil

28 190673GS MANIFOLD

45 190578GS PIN

62 190581GS CAP

76 194298GS THERMAL RELIEF

77 190585GS OIL BOTTLE (not shown)

A 190594GS KIT, UNLOADER

B 190670GS KIT,WATER INLET

C 190669GS KIT, BREATHER TUBE

D 193808GS KIT, HEAD BRASS

Item Part # Description

E 193806GS KIT, CHECK VALVES

F 190592GS KIT, INLET CHECK

G 190593GS KIT, CHEMICAL INJECTION

H 193807GS KIT, SEAL SET

J 189971GS KIT, CHEMICAL HOSE

K 193971GS KIT, PIPE FITTING

L 193972GS KIT, UNLOADER SEAT

NOTE: Item letters A - L are service kits and include all

parts shown within the box.

TABLA DE CONTENIDOS

Reglas De Seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22

Conozca Su Maquina Lavadora De Presion. . . . . . . . . . . . . . . . . 23

Ensamblaje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-26

Funcionamiento. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-29

Mantenimiento. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-32

Almacenamiento. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Diagnosticos De Averías. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Piezas De Recambio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19

Garantia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

DESCRIPCIÓN DEL EQUIPO

Lea este manual de manera cuidadosa y

familiarícese con su lavadora a presión. Conozca

sus usos, sus limitaciones y cualquier peligro

relacionado con el mismo.

Este manual contiene información referente el lavador a alta

presión que funciona a 2,700 psi, a un promedio de flujo de

2.5 galones por minuto. Este sistema profesional de alto poder y

de alta calidad, posee una llanta de 10 pulgadas, una bomba

equipada con un sistema de enfriamiento, un sistema de inyección

química, una extensión de lanzas que se pueden conectar

rápidamente, gafas de seguridad, una manguera de alta resistencia

de 25 pies y muchísimo más.

Se ha hecho cada esfuerzo posible para asegurarse que la

información que aparece en este manual es exacta y se encuentra

actualizada. Sin embargo, nosotros se reserva el derecho a

cambiar, alterar o de otra manera mejorar, el producto y este

documento en cualquier momento, sin previo aviso.

REGLAS DE SEGURIDAD

Éste es el símbolo de alerta de seguridad. Sirve

para advertir al usuario de un posible riesgo para

su integridad física. Siga todos los mensajes de

seguridad que figuren después de este símbolo

para evitar lesiones o incluso la muerte.

El símbolo de alerta de seguridad ( ) es usado con una palabra

(PELIGRO,ADVERTENCIA, PRECAUCIÓN), un mensaje por

escrito o una ilustración, para alertarlo acerca de cualquier

situación de peligro que pueda existir. PELIGRO indica un riesgo

el cual, si no se evita, causará la muerte o una herida grave.

ADVERTENCIA indica un riesgo el cual, si no se evita, puede

causar la muerte o una herida grave. PRECAUCIÓN indica un

riesgo, el cual, si no se evita, puede causar heridas menores o

moderadas. PRECAUCIÓN, cuando se usa sin el símbolo de

alerta, indica una situación que podría resultar en el daño del

equipo. Siga los mensajes de seguridad para evitar o reducir los

riesgos de heridas e inclusive la muerte.

Símbolos de Peligro y Significados

En el estado de California es obligatorio, según la ley, el uso de

apagachispas (Sección 4442 del Código de Recursos Públicos de

California). Otros estados pueden tener leyes similares. Las leyes

federales se aplican en tierras federales. Si equipa el silenciador

con un apagachispas, este deberá ser mantenido en buenas

condiciones de trabajo.

Reglas de Seguridad

Sección

El escape del motor de este producto contiene

elementos químicos reconocidos en el Estado de

California por producir cáncer, defectos de nacimiento u

otros daños de tipo reproductivo.

ADVERTENCIA

Fuego

Explosión

Gases Tóxicos

Superficie Caliente

Partes en Movimiento

Descarga Eléctrica

Superficies Resbalosas

Caer

Contragolpe

Objetos Voladores

Inyección Líquida

Page is loading ...

Troy Built 1904 User manual

Brand: Troy Built

Model: 1904

Category: High-pressure cleaners

Type: User manual

Download PDF

report

in other languages

español: Troy Built 1904 Manual de usuario

Troy Built 1904 User manual

Troy Built 1904 User manual

in other languages

Other documents