the great outdoors by Minka Lavery 72420-212 Operating instructions

Brand: the great outdoors by Minka Lavery

Model: 72420-212

Type: Operating instructions

The great outdoors by Minka Lavery 72420-212 is a versatile lighting fixture suitable for both indoor and outdoor use. With its easy installation process, it can be mounted on an outlet box using the provided crossbar and mounting screws. The fixture allows for easy bulb replacement and features a latch to open the door for bulb access and maintenance. The knurled knob ensures a secure attachment of the fixture body to the nipple, while the clear caulking helps prevent moisture from entering the outlet box, making it suitable for outdoor applications.

INSTALLATION INSTRUCTIONS

For Model 72420-212 (Rev. 06/19/2013)

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUI T BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1

Fig. 2

Fig. 3

PREPARING FOR INSTALLATION (Fig.1)

1. Shut off the power at the circuit breaker and remove

the old fixture and mounting hardware.

2. Carefully unpack your new fixture and lay out all the

parts on a clear area. Take care not to lose any small

parts necessary for installation.

3. Attach the crossbar (A) to the outlet box with mounting

screws (B) (Size: #8-32N*L0.5”). The side of the

crossbar marked “GND” must face out.

4. Thread the nipple (C) part way into the center hole of

the crossbar (A). Note: The length of nipple (C) into

crossbar (A) may be adjusted if necessary.

CONNECTING THE WIRES (Fig. 2)

5. Connect the electrical wires as shown in Fig. 2,

making sure that all wire connectors are secured. If

your outlet box has a ground wire (green or bare

copper), connect the fixture’s ground wire to it.

Otherwise, connect the fixture’s ground wire directly to

the crossbar using the green screw provided. After the

wires are connected carefully tuck them inside the

outlet box.

COMPLETING THE INSTALLATION (Fig.1)

6. Pull up the latch (E) and open the door.

7. Align the fixture body (G) to nipple (C) and secure with

knurled knob (D).

8. To prevent moisture from entering the outlet box and

causing a short, use clear caulking (i.e.

Indoor/Outdoor Silicone Sealant) to outline the outside

of fixture back-plate where it meets the wall leaving a

space at bottom to allow moisture a means to escape

(Fig.3).

9. Install 2*60W B10.5 bulb(s) (not included) in

accordance with the fixture’s specifications. (DON’T

EXCEED THE MAXIMUM WATTAGE RATING!!) (NE

PAS DEPASSER LA PUISSANCE NOMINALE

MAXIMALE!)

10. When replacing the glass (F), pull up the latch (E)

and open the door. Loosen the clips and remove glass

(F). After replacing the glass, re-tighten the glass clips,

and then close the door.

11. For installing or replacing bulbs at a later date, pull

up the latch (E) and open the door. (Fig.1)

Your installation is now complete. Return the power to the

junction box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

LA-2324E

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Green or

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

BACKPLATE

CAULKING

Set# A-016

-Crossbar

-Ground Screw

-Mounting Screw*2

MIN 90℃ SUPPLY CONDUCTORS

the great outdoors by Minka Lavery 72420-212 Operating instructions

the great outdoors by Minka Lavery 72420-212 Operating instructions

the great outdoors by Minka Lavery 72420-212 Operating instructions

Related papers

Other documents