Sony BluetoothH MEX-BT5100 User manual

Brand: Sony

Model: BluetoothH MEX-BT5100

Type: User manual

This manual is also suitable for

MEX-BT5100

AUDIO

OUT

REAR

AUDIO

OUT

FRONT

BUS

AUDIO

AUDIO OUT

FRONT

BUS AUDIO IN

/AUX IN

BUS

CONTROL IN

REMOTE

AUDIO OUT

REAR

SUB OUT (MONO)

3-276-519-41 (1)

Cautions

Be sure to install this unit in the dashboard of the car

as the rear side of the unit becomes hot during use.

• This unit is designed for negative earth 12 V DC

operation only.

• Do not get the leads under a screw, or caught in moving

parts (e.g. seat railing).

• Before making connections, turn the car ignition off to

avoid short circuits.

• Connect the yellow and red power input leads only

after all other leads have been connected.

• Run all earth leads to a common earth point.

• Be sure to in su late any loose un con nect ed leads with

electrical tape for safety.

• Do not cover the ventilation slots or heat sinks of the

unit.

Notes on the power supply lead (yellow)

• When connecting this unit in combination with other

stereo components, the connected car circuit’s rating

must be higher than the sum of each component’s fuse.

• When no car circuits are rated high enough, connect

the unit directly to the battery.

Parts Iist

• The numbers in the list are keyed to those in the

instructions.

• The bracket  and the protection collar  are

attached to the unit before shipping. Before mounting

the unit, use the release keys  to remove the bracket

 and the protection collar  from the unit. For

details, see “Removing the protection collar and the

bracket ()” on the reverse side of the sheet.

• Keep the release keys  for future use as they

are also necessary if you remove the unit from

your car.

Caution

Handle the bracket  carefully to avoid injuring your

ﬁ ngers.

Catch



Note

Before installing, make sure that the catches on both sides of

the bracket  are bent inwards 2 mm. If the catches are straight

or bent outwards, the unit will not be installed securely and may

spring out.

Installation/Connections

⫭塁濊䴾嵓徇㌉

Connection example

Notes (-

)

• Be sure to connect the earth lead before connecting the

ampliﬁ er.

• The alarm will only sound if the built-in ampliﬁ er is used.

Tip (-

)

For connecting two or more CD/MD changers, the source

selector XA-C40 (not supplied) is necessary.

Connection diagram

 To a metal surface of the car

First connect the black earth lead, then connect the orange/

white stripped, yellow, and red power input leads.

 To the power aerial control lead or power

supply lead of aerial booster ampliﬁ er

Notes

• It is not necessary to connect this lead if there is no power

aerial or aerial booster, or with a manually-operated

telescopic aerial.

• When your car has a built-in FM/AM aerial in the rear/side

glass, see “Notes on the control and power supply leads.”

 To AMP REMOTE IN of an optional power

ampliﬁ er

This connection is only for ampliﬁ ers. Connecting any other

system may damage the unit.

 To the interface cable of a car telephone

 To a car’s illumination signal

Be sure to connect the black earth lead to a metal surface

of the car ﬁ rst.

 To the +12 V power terminal which is

energized in the accessory position of the

ignition key switch

Notes

• If there is no accessory position, connect to the +12 V

power (battery) terminal which is energized at all times.

Be sure to connect the black earth lead to a metal surface

of the car ﬁ rst.

• When your car has a built-in FM/AM aerial in the rear/side

glass, see “Notes on the control and power supply leads.”

 To the +12 V power terminal which is

energized at all times

Be sure to connect the black earth lead to a metal surface

of the car ﬁ rst.

Notes on the control and power supply leads

• The power aerial control lead (blue) supplies +12 V DC when

you turn on the tuner.

• When your car has built-in FM/AM aerial in the rear/side glass,

connect the power aerial control lead (blue) or the accessory

power input lead (red) to the power terminal of the existing

aerial booster. For details, consult your dealer.

• A power aerial without a relay box cannot be used with this

unit.

Memory hold connection

When the yellow power input lead is connected, power will

always be supplied to the memory circuit even when the ignition

switch is turned off.

SUB OUT

(

MONO

)

AUDIO OUT

REAR

AUDIO OUT

FRONT

BUS AUDIO IN

BUS CONTROL IN

Equipment used in illustrations (not supplied)

㌶♺ᶑ䗨塁仒濃曂斨彥濄

from car aerial

Ừ兎㯡帮⢍䴾

Rear speaker

⻰㌾俖◌

Front speaker

↱㌾俖◌

Active subwoofer

㙭㷴峩Ẳ杗㌾俖◌

Rotary commander RM-X4S

㔯庭⹳㌋↚◌!SN.Y5T

Power ampliﬁ er

∃䋫㒢⢋◌





× 2



× 4



CD/MD changer

DE0NE!㌿䠃㧃

BUS AUDIO IN

BUS CONTROL IN

Source selector*

杗㷴応㐫◌*

XA-C40

* not supplied

曂斨彥

㱌び

䒕㔠⚌ợ䒌徲䥯ᶑ㚐㧃䗨倰曆㙧嫮䄕濇娯∽⼩⭫

㚐㧃⫭塁⚌㯡帮䗨⁤埌㛣ᶑɁ

• 㚐㧃⍎偡ợ䒌射㣙㌉⚔!23!W!䙘㲥晟㷴Ɂ

!ᵱ壥ợ⭲䴾⢢⚌圞䳖ᵯ濇ㅺ䷂㋿⚌䥟∹恌Ṛᵮ

濃⣦濕⸋㡩㇚ㆯᵮ濄Ɂ

• 徇㌉䴾嵓ᶯ↱濇娯敀擭㯡帮湂㿏塁仒ṉ₱⹹峛䝑

嵓Ɂ

• 渧凖⏰䱩凖晟㷴府⃉⭲䴾⼩杬⚌ㆤ㙭⃚⫧⭲䴾恡徇

㌉⫰䓆ṉ⻰ㆱ徇㌉Ɂ

• ⭫ㆤ㙭⚔䴾恡徇㌉↔⍰ᵤ㌉⚔湂Ɂ

!䆖ᷪ⫭⃌濇娯䠞姱㇮㯶㙭徇㌉䗨⭲䴾䒌晟◌億⶚≩

䲒徖垰䲹䵇Ɂ

•!娯≣忒启㚐㧃䗨彾栌⪸ㅺ㓇䄕恌ằɁ

晟㷴⭲䴾杬䝉濃渧凖濄

• ⭫㚐㧃八⃚⫧䨯樸俖塁仒䲨⍬ợ䒌㖦濇ㆤ徇㌉䗨㯡

帮晟嵓⬝愳⼩杬⢋㔠㬳Ὧ塁仒ὁ明䳖⬝愳䗨䶡⏰Ɂ

• 䓚㯡帮晟嵓⬝愳ᵱ⢄⢋㖦濇娯⭫㚐㧃䙘㌉八晟㯄䙜

徇㌉Ɂ

晚Ṛᵤ夡埌!

• ♺䢞㓜⪻八娎㕲㙜ᶑ䗨㓜⪻㖓ᵤ兘䗨Ɂ

• ㆼ㜚!



!⏰ὁ嫛䐔!



!⚌⅞⹄ᶯ↱ⵖ䳷塁⚌㚐塁仒

ᵮɁ⚌⫭塁㚐塁仒ᶯ↱濇娯€ợ䒌擯拺揔≽!



!⭫

ㆼ㜚!



!⏰ὁ嫛䐔!



!⼂㚐塁仒ᵮ㈪ᵯɁ姗䲔娎㕲濇

娯⌧壯㚐来⌱曆ĥ㈪ᵯὁ嫛䐔⏰ㆼ㜚!)



*ĦɁ

• ⣦㜀Ḯ⻰壥⭫㚐塁仒⼂㯡帮ᵮ㈪ᵯ濇᷃壥ợ䒌擯拺

揔≽濇♄㫈娯ὁ⪼⣡擯拺揔≽!



!ṉ´Ḯ⻰ợ䒌Ɂ

㱌び

㉣⌺ㆼ㜚!



!㖦濇娯䇝↉㱌び↉‛↔ㆯ㉫Ɂ

㈰懈



妟

⫭塁ᶯ↱濇⼩杬⭫ㆼ㜚!



!⃍Ῐ䗨㈰懈⍵⃋⺲㙖!3!nnɁ⣦㜀㈰懈

䪪䙘ㅺ⍵⡺⺲㙖濇↫㚐塁仒⭫䂅㰹䇆♞⫭塁濇ᶊ⍓偡⺬⅞Ɂ

䴾嵓徇㌉♺ữ!

妟濃-A濄

•!∽⼩⚌㌉㒢⢋◌ᶯ↱徇㌉⚔䴾Ɂ

•!⣦㜀ợ䒌⃩⹞㒢⢋◌濇➕嫊◌⭫⍎䗠⅞ᵤ俖➕嫊俖Ɂ

㌴䢞濃-B-

濄

剉壥徇㌉!3!⍔ㅺ㙘⡾!DE0NE!㌿䠃㧃㖦濇⼩杬ợ䒌杗㷴応㐫◌!

YB.D51濃応屠Ṛ濄Ɂ

䴾嵓徇㌉♺!

!徇㌉兗㯡帮䗨愵⯐埌曆

棺€徇㌉渵凖㌉⚔⭲䴾濇䂚⻰⃱徇㌉㦽濊䗡㠁䱯濇渧凖⏰䱩

凖晟㷴府⃉⭲䴾Ɂ

!徇㌉兗晟∹⢍䴾㌋↚⭲䴾ㅺ⢍䴾⊫⠷㒢⢋◌䗨晟㷴

⭲䴾

妟

•!⣦䂅晟∹⢍䴾ㅺ⢍䴾⊫⠷◌濇ㅺ㙭ㆯ∹⢻䬅⹳⢍䴾濇ἣᵱ

杬徇㌉㫈⭲䴾Ɂ

•!「㯡帮䗨⻰濊Ῐ䌟䏧䧻ᶑ⣦㜀㙭⃋⹞!GN0BN!⢍䴾濇⋗娯⌧

䙯ĥ㌋↚䴾⏰晟㷴䴾杬䝉ĦɁ

!徇㌉兗応屠䗨∃䋫㒢⢋◌䗨!BNQ!SFNPUF!JO濃㒢

⢋◌徽㌋府⃉濄

㚐徇㌉󰜪䒌㔠㒢⢋◌Ɂ徇㌉ṟẹ⃚⫧䱟䳕⍓偡㙧㍱⡂㚐㧃Ɂ

!徇㌉兗㯡帮晟姕䗨㌉⍇晟一

!

徇㌉

兗㯡帮䃋㕲奮嗃

⼩杬棺€⭫渵凖㌉⚔⭲䴾徇㌉兗㯡帮䗨愵⯐埌曆Ɂ

!

徇㌉兗⚌湂㿏揔≽擯敀䗨斨Ṛằ仒ᵮ彾晟䗨

,23!W!

晟㷴䩓⪴

妟

•!剉㯶㙭斨Ṛằ仒濇↫娯徇㌉兗⤯䲦彾晟䗨!,23!W!晟㷴

濃晟㯄濄䩓⪴Ɂ

!⼩杬棺€⭫渵凖㌉⚔⭲䴾徇㌉兗㯡帮䗨愵⯐埌曆Ɂ

•!「㯡帮䗨⻰濊Ῐ䌟䏧䧻ᶑ⣦㜀㙭⃋⹞!GN0BN!⢍䴾濇⋗娯⌧

䙯ĥ㌋↚䴾⏰晟㷴䴾杬䝉ĦɁ

!徇㌉兗⤯䲦彾晟䗨!,23!W!晟㷴䩓⪴

⼩杬棺€⭫渵凖㌉⚔⭲䴾徇㌉兗㯡帮䗨愵⯐埌曆Ɂ

㌋↚䴾⏰晟㷴䴾杬䝉

•!ㆷ擯娣婋◌晟㷴㖦濇晟∹⢍䴾䗨㌋↚⭲䴾濃唱凖濄ἣ偡㌴ỿ!

,23!W!䙘㲥晟Ɂ

•!剉「䗨㯡帮⻰濊Ῐ䌟䏧䧻ᵮ㙭⃋⹞!GN0BN!⢍䴾濇杬⭫晟∹⢍䴾

㌋↚⭲䴾濃唱凖濄ㅺ幸∍晟㷴府⃉⭲䴾濃䱩凖濄徇㌉↔䍢㙭⢍

䴾⊫⠷◌ᵮ䗨晟㷴䩓⪴ᵮɁ姗䲔⃋⬝娯⍵戛⒒⒪婒姆Ɂ

•!㚐㧃ᵱ偡ợ䒌ᵱ⃛´䷠晟◌䘶䗨晟∹⢍䴾Ɂ

ὁ㉥奼ㄚ䗨䴾嵓徇㌉㰹

䓚徇㌉⣡渧凖晟㷴府⃉⭲䴾㖦濇⋗ợ㯡帮䗠∹㧃湂㿏揔≽敀擭濇

晟㷴ḱ⭫⭱奼ㄚ晟嵓ỿ晟Ɂ



AMP REM

Max. supply current 0.3 A

㙤⢋㷴晟㲥!1/4!B

Fuse (10 A)

ὁ明䳖!)21!B*

Blue/white striped

唱濊䗡㠁䱯

Red

䱩凖

Yellow

渧凖

White

䗡凖

Green

䴄凖

Purple

䲏凖

White/black striped

䗡濊渵㠁䱯

Grey/black striped

㿔濊渵㠁䱯

Green/black striped

䴄濊渵㠁䱯

Grey

㿔凖

Left

ⵊ

Right

⍗

Left

ⵊ

Right

⍗

ANT REM

Black

渵凖

Blue

唱凖

Max. supply current 0.1 A

㙤⢋㷴晟㲥 1/2!B

Purple/black striped

䲏濊渵㠁䱯

Source selector

(not supplied)

杗㷴応㐫◌

)曂斨彥*

XA-C40

Supplied with the CD/MD changer

斨⶚㔠!DE0NE!㌿䠃㧃

ATT

ILLUMINATION

Orange/white striped

㦽濊䗡㠁䱯

Light blue

㵅唱凖

MEX-BT5100

RCA pin cord (not supplied)

Be sure to match the colour-coded

cord for audio to the appropriate jacks

from the unit. If you connect an optional

CD/MD changer, you cannot use AUX

IN terminal.

Auxiliary optional equipment such as

portable DVD player (not supplied)

Supplied with the auxiliary equipment

Supplied with XA-C40

Insert with the cord upwards.

!SDB!慁⛯㌶枑晟䴾濃曂斨彥濄

!杗枟⭲䴾䗨枳凖⼩杬八塁仒ᵮ㫇䠞䗨㌶

⪸枳凖ᵤ兘Ɂ⣦㜀徇㌉応屠䗨!DE0NE!㌿

䠃㧃濇↫「⭫䂅㰹ợ䒌!BVY!JO!䩓⪴Ɂ

幸∍応屠塁仒濇⣦ἣ㒀⹳!EWE!㐑㒢㧃

濃曂斨彥濄

斨⶚㔠幸∍塁仒

斨⶚㔠!YB.D51

!晟䴾⍵ᵮ㌶⃉Ɂ

Bluetooth™

Audio System

Notes on speaker connection

• Before connecting the speakers, turn the unit off.

• Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.

• Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the

left speaker.

• Do not connect the earth lead of this unit to the negative (–)

terminal of the speaker.

• Do not attempt to connect the speakers in parallel.

• Connect only passive speakers. Connecting active speakers

(with built-in ampliﬁ ers) to the speaker terminals may damage

the unit.

• To avoid a malfunction, do not use the built-in speaker leads

installed in your car if the unit shares a common negative (–)

lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Note on connection

If speaker and ampliﬁ er are not connected correctly, “Failure”

appears in the display. In this case, make sure the speaker and

ampliﬁ er are connected correctly.

徇㌉㌾俖◌㖦䗨㱌びᷯ杩

•!徇㌉㌾俖◌晟䴾ṉ↱濇娯€敀擭㚐㧃晟㷴Ɂ

•!ợ䒌斟ㇻ䆖!5.9Ã!ᵸ⃛㙭崗⢄∃䋫喹䍪⬝愳䗨㌾俖◌濇ṉ₱㍱

⡂㌾俖◌Ɂ

•!ᵱ壥⭫㌾俖◌䩓⪴徇㌉↔帮帏ᵮ濇ㅺ⭫⍗㌾俖◌䩓⪴八ⵊ㌾俖

◌䩓⪴䙜徇㌉Ɂ

•!Ⅻ≣⭫㚐㧃䗨㌉⚔⭲䴾徇㌉兗㌾俖◌䗨射濃.濄㌉䴾䩓Ɂ

•!㌾俖◌ᵱ⍓ᶊ俓徇㌉Ɂ

•!娯󰜪徇㌉䂅㷴㌾俖◌Ɂ剉⭫㙭㷴㌾俖◌濃⶚⃋仒㒢⢋◌濄徇㌉

↔㌾俖◌䩓⪴ᵮ㙧㍱⡂㚐㧃Ɂ

•!剉㚐塁仒ợ䒌ⵊɀ⍗㌾俖◌䗨⃕䒌射㣙濃.濄⭲䴾濇䆖ᷪ忣₱㒩

昀濇Ⅻ≣ợ䒌ⵖ⫭塁⚌㯡帮⃋䗨⃋⹞㌾俖◌⭲䴾Ɂ

•!娯≣⭫㚐塁仒㌾俖◌⭲䴾䙜᷶徇㌉Ɂ

㙭敀徇㌉㱌びᷯ杩

⣦㜀㚎㫇䠞徇㌉㌾俖◌⏰㒢⢋◌濇↫染䢞ⶹᵮ㙧⅞䍢ĥGbjmvsfĦɁ

㫈㖦濇娯㫇䠞徇㌉㌾俖◌⏰㒢⢋◌Ɂ

12 3

182 mm

53 mm







Dashboard

⁤埌㛣

A TOYOTA

to dashboard/centre console

兗⁤埌㛣濊ᶑ⢒㌋↚䬕

Bracket

ㆼ㜚

Bracket

ㆼ㜚

B NISSAN



to dashboard/centre console

兗⁤埌㛣濊ᶑ⢒㌋↚䬕

Bracket

ㆼ㜚

Bracket

ㆼ㜚



Existing parts supplied with your car

昌㯡帮斨彥䗨恌Ṛ

max. size

5 × 8 mm

㙤⢋⮞⭜

69!nn

max. size

5 × 8 mm

㙤⢋⮞⭜

69!nn

max. size

5 × 8 mm

㙤⢋⮞⭜

69!nn

max. size

5 × 8 mm

㙤⢋⮞⭜

69!nn

Face the hook

inwards.

㋿懈㚁塅曆Ɂ

Claws

懈䆎

Mounting the unit in a Japanese

car

You may not be able to install this unit in some makes of

Japanese cars. In such a case, consult your Sony dealer.

Note

To prevent malfunction, install only with the supplied screws .

How to detach and attach the

front panel

Before installing the unit, detach the front panel.

-A To detach

Before detaching the front panel, be sure to press .

Press , then slide the front panel to the right, and

gently pull out the left end of the front panel.

-B To attach

Place the hole  of the front panel onto the spindle 

on the unit, then lightly push the left side in.

Warning if your car’s ignition

has no ACC position

After turning the ignition off, be sure to press

and hold  on the unit until the display

disappears.

Otherwise, the display does not turn off and this causes

battery drain.

RESET button

When the installation and connections are completed, be

sure to press the RESET button with a ballpoint pen, etc.,

after detaching the front panel.

Precautions

• Choose the installation location carefully so that the

unit will not interfere with normal driving operations.

• Avoid installing the unit in areas subject to dust, dirt,

excessive vibration, or high temperatures, such as in

direct sunlight or near heater ducts.

• Use only the supplied mounting hardware for a safe

and secure installation.

Mounting angle adjustment

Adjust the mounting angle to less than 45°.

Removing the protection collar

and the bracket

Before installing the unit, remove the protection

collar  and the bracket  from the unit.

1 Remove the protection collar .

Pinch both edges of the protection collar , then

pull it out.

2 Remove the bracket .

 Insert both release keys  together between

the unit and the bracket  until they click.

 Pull down the bracket , then pull up the unit

to separate.

Frequency select switch

The AM (FM) tuning interval is factory-set to the 9 k

(50 k) position. If the frequency allocation system of

your country is based on 10 kHz (200 kHz) interval, set

the switch on the bottom of the unit to the 10 k (200 k)

position before making connections.

Mounting example

Installation in the dashboard

Notes

• Bend these claws outward for a tight ﬁ t, if necessary (-

• Make sure that the 4 catches on the protection collar  are

properly engaged in the slots of the unit (-

Existing parts supplied with your car

昌㯡帮斨彥䗨恌Ṛ

Fire wall

斖㿏⠥







ợ䒌↱㱌びᷯ杩

• Ḹ䲔応⌺⫭塁ằ仒濇ṉợ㚐塁仒ᵱⷖ㑢㫇⶜䗨椹椿

㐱ỀɁ

• 忣₱⭫㚐㧃⫭塁⚌⌻㿔⟙濇㯅䇍⏰⺛䀬㊓∹⻕杣䗨

⊤❃濇ㅺ⫭塁⚌樼㸏喹濇⣦䙘⭱旡₭ᵯㅺ䄕㮇䬅德

斨張Ɂ

!䆖ᷪ⫭塁⫭⃌⏰⍓曄濇娯ợ䒌斨彥䗨⫭塁㤯ṚɁ

⫭塁夶⸊ᶯ娣㓘

娯⚌!56ṉ⃋娣㓘⫭塁夶⸊Ɂ

㈪ᵯὁ嫛䐔⏰ㆼ㜚!

⫭塁ᶯ↱濇娯€⼂㚐塁仒ᵮ㈪ᵯὁ嫛䐔!



!⏰ㆼ㜚!



1! ㈪ᵯὁ嫛䐔



㊳ẳὁ嫛䐔!



! 䗨⃍忮濇䂚⻰⍵⡺㈭⅞ὁ嫛

䐔Ɂ

2! ㈪ᵯㆼ㜚





!⭫⃍㇮擯拺揔≽!



!ᵤ峛㌶⃉塁仒⏰ㆼ㜚!



ᶯ擷濇䙘兗信↔ⓤ┶俖Ɂ



!⍵ᵯ㈭ㆼ㜚!



濇䂚⻰⍵ᵮ㈭塁仒濇ợᶯ䙜

᷶傏晆Ɂ

枟䋫応㐫擯敀

BN濃GN濄娣婋擷旸⚌⅞⹄↱堏妑⫾⚌!:!l濃61!l濄ằ仒

ᵮɁ剉尘♯䗨枟䋫Ⅺ悱䱟䳕㖓❞㔠!21!lI{濃311!lI{濄

擷旸濇徇㌉↱濇娯⭫㚐㧃ⷹ恌ᵮ䗨擯敀妑⫾⚌21l

濃311!l濄ằ仒ᵮɁ

⫭塁䢞ữ!

⫭塁⚌⁤埌㛣塅

妟!

•!剉㙭⼩壥濇↫⍓⍵⡺⺲㙖彽᷿⋅懈䆎濃.3濄Ɂ

•!⼩杬⭫ὁ嫛䐔!!ᵮ䗨!5!Ὧ懈䆎㫇䠞◽⍬⚌塁仒䗨⋅㥡ᶑ

濃.4濄Ɂ

⭫㚐㧃⫭塁㔠㕉㚐䒆㯡帮ᵮ!

㙭᷿㕉㚐䒆㯡帮ᵱ偡⫭塁㚐㧃濇⚌彽䦒〩⻆ᵯ濇娯⍵!

Tpoz!䳷戛⒪婒姆Ɂ

妟

䆖斖㫆䗠䒃㒩昀濇⫭塁㖦⍎偡ợ䒌斨彥䗨圞䳖!Ɂ

⣦ẹ㈪⋜⏰塁悱↱曆㛣!

⫭塁㚐㧃ᶯ↱濇娯€㈪⋜↱曆㛣Ɂ



.B!㈪⋜!

㈪⋜↱曆㛣ᶯ↱濇杬€㉭ᵯ!!拙Ɂ㉭!濇

䂚⻰⭫↱曆㛣㸵⍵⍗Ῐ濇䂚⻰幹幹㈭⅞↱曆㛣䗨ⵊ

ῘɁ



.C!塁悱

⭫↱曆㛣䗨⪸!



! ⭱㷺㚐㧃ᵮ䗨幜!



濇䂚⻰幹幹⚔

㌌⃉ⵊῘɁ

⣦㜀「䗨㯡帮⹹㐲㯶㙭!BDD!

ằ仒㖦䗨嫊⎮

敀擭⹹㐲⻰濇⼩杬㉭ẳ㚐㧃ᵮ䗨! ! ᵱ㒢濇䙘兗染

䢞㳬⢕Ɂ

⎊↫濇染䢞⭫ᵤ䙘擯去⼂佰㳬佻晟㯄Ɂ

SFTFU!㉭慹

䓚⫭塁⏰徇㌉⫰ㅴ㖦濇娯∽⼩€㈪⋜↱曆㛣濇⃱䒌⌃

⪴䪪䪭㉭⠷!SFTFU!㉭慹Ɂ









Sony BluetoothH MEX-BT5100 User manual

Brand: Sony

Model: BluetoothH MEX-BT5100

Type: User manual

This manual is also suitable for

MEX-BT5100

Download PDF

report

Sony BluetoothH MEX-BT5100 User manual

This manual is also suitable for

Sony BluetoothH MEX-BT5100 User manual

Related papers