MyBinding Best-Rite Standard Bulletin Board Cabinet 2 Sliding Doors Assembly Instruction
- Type
- Assembly Instruction
The MyBinding Best-Rite Standard Bulletin Board Cabinet 2 Sliding Doors is a versatile and durable storage solution for your office or home. With its two sliding doors and adjustable shelves, this cabinet can accommodate a variety of items, including files, binders, and supplies. The cabinet is made of sturdy steel construction with a powder coat finish for added durability. It also features a locking mechanism to keep your belongings safe and secure.
The MyBinding Best-Rite Standard Bulletin Board Cabinet 2 Sliding Doors is a versatile and durable storage solution for your office or home. With its two sliding doors and adjustable shelves, this cabinet can accommodate a variety of items, including files, binders, and supplies. The cabinet is made of sturdy steel construction with a powder coat finish for added durability. It also features a locking mechanism to keep your belongings safe and secure.
1
Wall Hung Bulletin Board
Cabinets
Mounting Instructions
2
Part Drawing Description Qty
Do not use unless all screws are tight. At least every six months, check all screws to be sure
they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until
repairs are made by your dealer using factory authorized parts.
Important Information
Hardware List
Use Screw Anchor (C) in place of Screw
Anchor (B) for Drywall Applications.
A-1 Long Screw (1-1/4” )
A-2 Short Screw ( 3/8”)
B Screw Anchor - Concrete
C Screw Anchor - Drywall
D L-Clip (large)
E L-Clip (small)
F Z-Hanger
P-1 Bulletin Board Cabinet 1 EA
EWall Hung Bulletin Board Cabinets
(One, Two or Three Door)
3
To Attach to Wall:
Identify and Separate all the Parts and Hardware.
Determine the type wall you are going to mount your new Bulletin Board Cabinet (P-1) on.
Decide the location and draw a line under the cabinet and on top of the cabinet on the wall as
shown in illustration #1.
1.
Illustration # 1
2.
3.
P-1
Draw Line
on Wall
Determine the type mounting brackets that are attached to the back of your Bulletin Board
Cabinet (P-1) . Find the mounting instructions that match your type Cabinet’s mounts on the
following pages. .
4a. Bulletin Board Cabinets with four Cross Type mounting brackets:
5a.
Measure the distance up from the bottom of the Bullentin Board Cabinet up to the center point
of one of the bottom Cross Brackets as shown in Detail #2a. Add thisdistance on top of your
bottom Cabinet wall mark and mark a second line that is parallel as shown in illustration #2a.
.
Illustration # 2a
Cross Bracket
Bottom of
Cabinet
Bottom of
Cabinet Line
Second Line
Detail #2a
4
6a.
Measure the Length and Width of the center points of the Cross Mounting Brackets as shown
in Detail #3a. Use these dimensions to mark your four Mount Screw holes on the wall as
shown in illustration #3a. .
.
Length
Width
Detail #3a
Illustration # 3a
Mount Screw
Holes .
Bottom of
Cabinet Line
7a.
(1) Use Long Screw (A-1) for attaching direct into wood and metal wall studs.
(2) Use Screw Anchor (B) and Long Screw (A-1) for attaching into Concrete walls.
(3) Use Screw Anchor (C) and Long Screw (A-1) for attaching into Drywall.
CHART A
Check Chart A for the correct Screw and Anchor for your type wall.
A-1
A-1
B
A-1
C
1/4”
(1)
(2)
(3)
(1)
(2)
(3)
5
4b. Bulletin Board Cabinets with Cross Type Mounting Brackets at the top
and L Clips at the bottom:
8a.
Install a Small L Clip (E) on the bottom drawn line in the center. Use the correct hardware for
your type wall. Hang the Cabinet by placing the Screw heads into the Cross Type mounting
brackets and resting dow on the bottom Small L Clip. Use a Short Screw (A2) through the
bottom Small L Clip’s leg to secure the cabinet in place. See illustrations # 4a and 5a.
Illustration # 4a
E
Illustration # 5a
A2
Bottom edge
of cabinet
Top edge of
cabinet
Measure the distance from the top of the Bulletin Board Cabinet down to the top center point
of the Cross Brackets as shown in Detail #2b. Draw a lower line parallel to the top Cabinet
line. Measure the distance between the Top Cross Type brackets and mark this distance on
the second top line you just drew. Install the correct mounting hardware for your type wall in
these marks. See illustration #2b. .
5b.
Illustration # 2b
Detail # 2b
A1
Bottom of
Cabinet
Top of
Cabinet
6
6b. Install the Large L Clips (D) on the bottom drawn line of Cabinet as shown in illustration #3b.
D
A1
Illustration # 3b
7b.
D
D
A2
Place the Cabinet’s Cross Type Top Mounting brackets over the heads of the top hanging
Screws and lower Cabinet doewn onto the bottom Large L Clips (D). Secure in place
using Short Screws (A2) into the bottom leg of the L Clip and into the Cabinet’s bottom
frame as shown in illustration #4b.
7
4c.
Bulletin Board Cabinets with Z Hanger Bar at top and L Clip at bottom:
5c.
Measure the distance down fro the top edge of your Cabinet to the center point of the Z
Hanger Bar that is screwed to the back. Measure down this same amount from the top
line you drew on the wall and draw a line parallel to it. This will be the top edge location
of the wall mounted Z Hanger (F). Mount the Z Hanger (F) to the wall using the correct
hardware for your type wall (see Chart A on page 4). See Detail # 2c and illustration # 2c.
Illustration # 2c
Detail # 2c
F
Bottom of
Cabinet
A1
Top of
Cabinet
6c. Place a Small L Clip (E) in the center of the bottom drawn line of the Cabinet. Attach it to the
wall with the correct Hardware as shown in illustration #3c. .
A1
E
Illustration # 3c
7c.
Illustration # 4c
Hook the Cabinet’s Z-Hanger on the
Z-Hanger on the wall. Secure the
Cabinet to the wall and the Small
L Clip using Screw (A2) as
shown in illustration #4c.
A2
E
8
4d. Bulletin Board Cabinets with Large L-Clips Top and Bottom:
5d.
Install the Large L-Clips on the bottom drawn line with the correct Hardware for your type
wall. Make sure the bottom edge of the L-Clips are even with the bottom line when the
Screw (A1) is in the top of the L-Clips slot as shown in illustration #2d.
ED
A1
Illustration # 2d
6d. Install the top Large L-Clips so that they can be raised 1/2” above the top drawn line and then
pushed down to touch the line and the top of the board once it is installed. See illustration # 2d.
Bulletin Board Cabinets 1-30-14
1/2”
7d. Place the Cabinet on the bottom row of L-Clipsand tilt the Cabinet up against the wall. Push the
top L-clips down until they touch the top of the Cabinet. Secure the L-Clips to the Cabinet using
Small Screws (A2). .
Illustration # 3d
A2
A2
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
MyBinding Best-Rite Standard Bulletin Board Cabinet 2 Sliding Doors Assembly Instruction
- Type
- Assembly Instruction
The MyBinding Best-Rite Standard Bulletin Board Cabinet 2 Sliding Doors is a versatile and durable storage solution for your office or home. With its two sliding doors and adjustable shelves, this cabinet can accommodate a variety of items, including files, binders, and supplies. The cabinet is made of sturdy steel construction with a powder coat finish for added durability. It also features a locking mechanism to keep your belongings safe and secure.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Maxon RC-2B, RC-3B, RC-3B, RC-4B, RC-5B, RC-6K January 2000 Operating instructions
-
Hobart P660 User manual
-
-
-
-
-
Olivetti Jet-Lab 490 User manual
-
-
Strasser Woodenworks 27.650 Installation guide
-
SimplyNeu SNBR-BC User manual
