True Fitness MP 2.0 User manual

MP 2.0

AND

MP 2.5

A

SSEMBLY

M

ANUAL

AM-MP-2-0

022520

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 2 of 47

.

IMPORTANT:

All products shown are prototype. Actual product delivered may vary.

Product specications, features & soware are subject to change without notice.

For the most up-to-date owner’s manual please visit www.truetness.com.

For documents in additional languages please visit www.truetness.com/resources/document-library/

IMPORTANTE:

Todos los productos mostrados son prototipos. La realidad el producto suministrado puede diferir.

Especicaciones de productos, características y soware están sujetas a cambios sin previo aviso.

Para la más actualizada de este manual del propietario, por favor visite www.truetness.com

Para los documentos en otros idiomas, por favor visite www.truetness.com/resources/document-library/

IMPORTANT: Tous les produits présentés sont prototype. Le produit réel livré peut varier. Spécications du

produit, caractéristiques et logiciels sont sujettes à modication sans préavis. Pour la plus à jour le manuel du

propriétaire s'il vous plaît visitez www.truetness.com. Pour documents dans des langues supplémentaires,

veuillez www.truetness.com/resources/document-library/ de visite

重要提示：显示所有产品的原型。实际交付的产品可能有所不同产品规格，功能和软件如有更改，恕不另

行通知迄今为止对于大多数的使用说明书，请访问www.true󼵠tness.com 对于其他语言的文档，请访问

www.true󼵠tness.com/resources/document-library/

ھام:

جمیع المنتجات المعروضة ھي النموذج. قد تختلف المنتج الفعلي تسلیمھا

مواصفات المنتج، والمیزات والبرامج قابلة للتغییر دون إشعار.

لمعظم ما یصل حتى الآن دلیل المالك یرجى زیارة www.truetness.com.

للمستندات في لغات إضافیة، یرجى زیارة www.truetness.com/resources/document-library/

WICHTIG: Alle hier gezeigten Produkte sind Prototypen. Das tatsächliche Produkt ausgeliefert wird, kann

variieren. Produkt-Spezikationen, Funktionen und Soware können sich ohne vorherige Ankündigung

ändern. In den meisten Fällen bis zu Bedienungsanleitung Bisher besuchen Sie bitte www.truetness.com. Für

Dokumente in weiteren Sprachen nden Sie unter www.truetness.com/resources/document-library/

BELANGRIJK: Alle getoonde producten zijn prototype. Daadwerkelijke product geleverd kan verschillen.

Product specicaties, eigenschappen & soware zijn onderhevig aan verandering zonder kennisgeving. Voor

de meest actuele handleiding van de eigenaar kunt u terecht www.truetness.com. Voor documenten in andere

talen kunt u terecht op www.truetness.com/resources/document-library/

ВАЖНО: Все товары указаны прототипа. Фактический продукт, поставляемый могут отличаться.

Технические характеристики, особенности и программного обеспечения могут быть изменены без

предварительного уведомления. Для получения самой последней на сегодняшний день руководство по

эксплуатации пожалуйста, посетите www.truetness.com

.Для документов на другие языки, пожалуйста, посетите www.truetness.com/resources/document-library/

Strength

MP 2.0 & 2.5

A MESSAGE TO OUR CUSTOMERS

Frank Trulaske began TRUE Fitness® over thirty-ve year ago with the simple philosophy of delivering superior

tness products, service, and support. Today, TRUE is the global leader in premium tness equipment for the

commercial and residential markets. Our goal is to be the leader in technology, innovation, performance, safety

and style. TRUE has received many awards for its product over the years and remains the benchmark for the

industry. Fitness facilities and consumers invest in TRUE products for their durable commercial platforms used

in all its products, both commercial and residential alike.

e proud manufacturing tradition of quality and the culture of innovation at TRUE have given rise to a full line

of extraordinary cardio and strength equipment. As a result, people all over the world are beneting from the

TRUE experience. Innovation across the full product line has made TRUE successful and is a trademark of the

TRUE heritage. TRUE’s patented Heart Rate Control technology is just one of the remarkable ways we deliver

simple and superior performance every user can enjoy, and most importantly, use to achieve personal health and

tness goals.

At the heart of our success is the relentless and systematic life testing of both our products and their components.

We have dedicated employees who understand our philosophy is to deliver the best products in the world.

Our goal is to deliver the world’s best premium equipment for our customers’ health and tness solutions.

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 3 of 47

Strength

MP 2.0 & 2.5

S

AFETY

...................................................................................................................... 5

G

ENERAL

C

ARE

AND

M

AINTENANCE

............................................................................... 8

D

IMENSIONS

AND

W

EIGHT

............................................................................................ 9

P

REPARATION

............................................................................................................. 10

U

PRIGHT

C

ARTON

C

ONTENTS

........................................................................................ 11

C

HEST

P

RESS

C

ARTON

C

ONTENTS

................................................................................. 12

L

EG

E

XT

/C

URL

C

ARTON

C

ONTENTS

............................................................................... 13

A

CCESSORIES

AND

W

EIGHTS

........................................................................................ 14

I

NSTALLATION

& A

SSEMBLY

S

TEP

1: A

SSEMBLE

THE

C

HEST

P

RESS

............................................................... 15

S

TEP

2: A

SSEMBLE

THE

P

ADS

........................................................................... 16

S

TEP

3: A

SSEMBLE

THE

P

RESS

A

RM

................................................................. 17

S

TEP

4: I

NSTALL

C

HEST

P

RESS

C

ABLE

.............................................................. 18

S

TEP

5: I

NSTALL

THE

L

OW

P

ULLEY

C

ABLE

.......................................................... 20

S

TEP

6: A

SSEMBLE

THE

L

EG

E

XT

/C

URL

M

AIN

F

RAME

........................................ 24

S

TEP

7: A

SSEMBLE

THE

L

EG

E

XT

/C

URL

F

RONT

F

RAME

....................................... 25

S

TEP

8: A

SSEMBLE

T

HIGH

P

AD

......................................................................... 26

S

TEP

9: A

SSEMBLE

THE

A

DJUSTMENT

A

RM

........................................................ 27

S

TEP

10: A

SSEMBLE

THE

P

ADS

AND

H

ANDLES

................................................... 28

S

TEP

11: I

NSTALL

L

EG

E

XT

/C

URL

C

ABLE

.......................................................... 30

S

TEP

12: I

NSTALL

THE

C

HEST

P

RESS

W

EIGHT

S

TACK

.......................................... 33

S

TEP

13: I

NSTALL

THE

L

EG

E

XT

/C

URL

W

EIGHT

S

TACK

........................................ 35

S

TEP

14: A

SSEMBLE

THE

F

RONT

S

HROUD

.......................................................... 36

S

TEP

15: A

SSEMBLE

THE

L

EG

E

XT

/C

URL

B

RACE

............................................... 37

S

TEP

16: A

SSEMBLE

THE

R

EAR

S

HROUDS

......................................................... 38

S

TEP

17: P

LACE

THE

W

EIGHT

S

TACK

L

ABELS

..................................................... 39

S

TEP

18: I

NSTALL

THE

B

OLT

C

APS

.................................................................... 40

P

ROCEDURE

L

ABEL

..................................................................................................... 42

W

ARNING

L

ABELS

....................................................................................................... 43

S

ERVICE

..................................................................................................................... 44

P

ARAMOUNT

L

IMITED

W

ARRANTY

................................................................................. 45

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 4 of 47

Strength

MP 2.0 & 2.5

F

ACILITY

AND

U

SER

S

AFETY

P

RECAUTIONS

1. Review and understand all of the warning labels affixed to this machine and on the facility

safety sign.

2. Be certain that the machine operation is understood before it is used. Refer to th

e

instructional Procedure Label affixed to the machine.

3. Make sure all users are properly trained on how to use this equipment. If this machine is

being used in a commercial setting, end users may not have access to this Owners Manual. It

is the responsibility of the facility to instruct users as to the proper usage of the equipment as

well as making them aware of potential hazards. Maximum user weight is 300 lbs (136 kg).

4. Use each machine only for the intended exercise. Do not allow anyone to invent exercises not

included on the Instructional Procedure Label or the Intended Use Label.

5.

Do not modify the machine.

6. This equipment meets industry safety standards for stability when used for the intended

exercise. Do not allow straps, resistance bands or other means to be attached to

the

f

ramework of this machine to perform stretching or body weight exercises. This can result in

machine instability and lead to serious crushing injuries.

7.

Keep children away from this equipment. Adults should closely supervise use by teenagers.

8. It is recommended that users receive a thorough medical exam before commencing an

exercise program. All medical issues should be reviewed to ensure that weight training will

not aggravate pre-existing medical conditions.

9. If the machine appears damaged or inoperable, contact a facility staff member to place an

“OUT OF ORDER, DO NOT USE” sign on the machine until it is repaired. Only use Paramoun

t

supplied replacement components to service this machine.

10. Instruct users not to wear loose or dangling clothes or have headphone wires hanging when

using this equipment.

11. Do not attempt to free any jammed assemblies by yourself as this may cause injury.

12. On Plate Loaded and Free Weight machines:

12a. Use of spotter(s). Instruct users to seek the advice of the facility staff as to the

appropriate use of spotters when lifting. More then one spotter may be required

depending upon the amount of weight being lifted.

12b. Instruct users to load weight plates evenly and carefully (one side and then the other)

to avoid tipping equipment and crushing injuries.

12c. If the machine is equipped with safety stops or catches, inspect them and verify their

proper operation before use and make sure they are securely in place before using or

exiting the machine. Be certain members are instructed on how to operate and adjust

all safety mechanisms.

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 5 of 47

12d. This equipment is designed for standard olympic size weight plates with a 50mm bore

(1.9”).

12e. Do not exceed the maximum weight capacity of the machine. Maximum plate size is

45 lbs. (25 kg.).

13. On Selectorized and Cable equipped machines:

13a. Do not allow users to perform any exercise by holding the end of the cable and/or th

e

cable end fitting. Use only appropriate handles or attachments properly connected to

the cable end.

13b. Do not high-pin or double-pin the weight stack. Do not allow the machine to be used if

the top plate or weight stack is pinned in a raised position. Use an assistant and

carefully return the machine to the proper position with the cap plate resting on the top

weight. Inspect the entire length of the cable to ensure that it is properly seated in all

of the pulley grooves.

13c. Do not allow the use of weight plates or dumbbells to be used as a means to add

additional weight to the weight stacks. Use only the TRUE adder weight system

specifically designed for the machine.

I

NSTALLATION

S

AFETY

P

RECAUTIONS

1. Read this Installation Manual entirely before assembling this equipment.

2. Verify that there is adequate space surrounding this piece of equipment for safe access and

operation. Installation must meet ADA requirements for accessibility.

3. Install this piece of equipment on a solid level surface that does not deviate more then 1/8”

over a 10’ distance (or as defined and required by local building and architectural codes.

4. TRUE strongly recommends that all equipment be anchored to the floor to prevent movement

and increase stability.

• Due to the wide variation of flooring on which the unit can be installed, contact a

qualified contractor to determine an appropriate fastening system for your floor.

• Use 3/8” diameter hardware (10 mm) to anchor the machine. Anchors should have a

minimum pull out force of 220 lbs (110 kgs) for each position.

• When attaching the machine to the floor, if there is a gap between the machine foot

and the floor, do not use the anchor to remove the gap as this can cause the

machine frame to deform. Instead, place a shim between the bottom of the foot and

the floor, then tighten the anchor.

• Anchoring holes are provided on the feet of the frame. All anchoring locations must

be used when anchoring the equipment to the floor.

5. DO NOT install any fitness equipment near a pool, hot tub or other damp locations. Corrosion

caused by installation in these locations can lead to premature failure of components.

6. Be sure all hardware is tight before using this machine.

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 6 of 47

M

AINTENANCE

S

AFETY

P

RECAUTIONS

1. Refer to Maintenance Schedule label on the machine as well as this manual for when to

perform maintenance.

2. Check the function of your machine DAILY by verifying the following:

• Inspect cables and end fittings for any signs of wear. Replace if worn, frayed or

damaged with original Paramount replacement components.

• Verify that all adjustments are possible and carried out with ease. Make sure that

each adjustment pin inserts completely into each position without binding.

• Verify that safety catches and stops are in proper working order and engaged.

• Verify that the exercise is performed smoothly, free of noise and/or bindin

g.

• If equipped with a weight stack, verify that the proper weight selector pin is in place.

3. Check the function of your machine WEEKLY by verifying the following:

• Nuts, Bolts, and Fasteners: Check tightness weekly. If any hardware has become

loose, retighten and/or use Loctite

™

Threadlocker 242.

• Frames and Lifting Arms: Inspect weekly for integrity and function. Replace any

component at first signs of wear. Use only Paramount supplied components.

4. Replace any warning label at first sign of wear. Labels and the Facility Safety Sign may be

obtained from Paramount free of charge.

B

OLT

L

ENGTH

M

EASURING

G

UIDE

FLAT HEAD SCREW

BUTTON HEAD SCREW

HEX HEAD SCREW

SOCKET HEAD SCREW

1

23

4

5

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 7 of 47

IMPORTANT

Preventative maintenance is crucial to maintaining the function and safety of this equipment. Your

facility must establish written guidelines for preventative maintenance and keep written or online

records of the maintenance performed on these products. As a minimum, the items presented in

the SAFETY section of this document and the items that follow here, should be included in your

maintenance program.

1. Cables: Inspect end fittings daily for wear. Inspect the entire length of the cable weekly.

Replace cables at the first sign of wear and on an annual basis. If the cable tension has

been adjusted, be certain that the cable nut is tight.

2. Nuts, Bolts, and Fasteners: Check tightness weekly. If any hardware has become loose,

retighten and/or use Loctite

TM

brand Threadlocker 242. Be sure all hardware is tight

before using the machine.

3. Safety Catches: Inspect catches, stop rods and their associated fasteners weekly. Tighten

any loose hardware and replace any components at first signs of wear.

4. Frames: Wipe all machines down with a damp cloth and dry completely each day. This

includes painted parts, chrome parts and upholstered pads.

5. Painted and chrome plated parts: Use Simple Green or similar cleaner for light dirt and

grime. Use Turtle Wax Polishing Compound or a good car polish to remove heavier dirt

and grease as well as for polishing. DO NOT use solvents, lacquer thinner, acetone or

finger nail polish remover. For scuffs and marks that are not removed by the above

methods use a soft scrub cleanser. Make sure all parts are dry upon completion.

6. Weight stack enclosures (shrouds): Wipe down with a damp cloth as needed.

7. Exercise instruction labels: Clean with soap and water as needed.

8. Guide rods: Wipe all dirt and dust from the guide rods before applying a light application

of Tri-Flow

TM

or other teflon spray lubricant. Spray the Tri-Flow

TM

on a rag and then wipe

the guide rods with the rag. DO NOT use oil lubricants such as WD-40. Caution: Tri-Flow

TM

will stain car

pet and clothing.

9. Bronze bushings: Check monthly for signs of wear and replace as needed.

10. Linear Bearing Shafts: Wipe any accumulation of dust or other contaminants from the

shafts on a weekly basis. Apply a thin layer of a Teflon

®

(PTFE) grease on a weekly basis.

Paramount recommends Magnalube

®

brand.

11. When replacing any component, use only Paramount supplied parts.

12. Please refer to the General Maintenance Manual (part number: AM-GMM) for other

important safety and maintenance information.

13. Be sure all hardware is tight before using the machine.

Retain these instructions for future reference.

If you have any questions, do not hesitate to contact your Paramount dealer or Paramount Fitness

Corp. at (800)721-2121 or nasales@paramountfitness.com.

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 8 of 47

8

96” (244.0 cm)

72.5” (187.0 cm)

107” (272.0 cm)

[MP 2.5]

W

EIGHT

S

TACK

C

ONFIGURATION

M

ACHINE

WEIGHT

W

/

OUT

LEG

PRESS

M

ACHINE

WEIGHT

WITH

LEG

PRESS

A

PPROXIMATE

F

LOOR

L

OADING

2 X 170 lbs. 850 LBS [386 KG] 985 LBS [447 KG] 79 LBS/FT

2

[385 KG/M

2

]

1 X 170 lbs. and 1 X 250 lbs. 930 LBS [422 KG] 1065 LBS [483 KG] 85 LBS/FT

2

[416 KG/M

2

]

2 X 250 lbs. 1010 LBS [458 KG] 1145 LBS [519 KG] 92 LBS/FT

2

[447 KG/M

2

]

M

ACHINE

W

EIGHT

AND

F

LOOR

L

OADING

“I

N

U

SE

” M

ACHINE

D

IMENSIONS

Machine Height: 83.75” (212.7 cm)

MAXIMUM USER WEIGHT IS 300 LBS. (136 KG.)

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 9 of 47

R

EQUIRED

T

OOLS

Ratchet Wrench and Sockets:

1/2” , 9/16”, 6” ratchet extension

Wrenches: 1/2” , 9/16” , 7/8” and 15/16”

(or an adjustable crescent wrench).

Rubber mallet.

Allen wrenches:

(included with the machine)

3 mm, 5 mm, 6 mm, 8 mm,

Hardware Measurement Guide:

SHCS - SOCKET HEAD CAP SCREW

FHCS - FLAT HEAD CAP SCREW

HHCS - HEX HEAD CAP SCREW

BHCS - BUTTON HEAD CAP SCREW

MEASURE BOLT

FROM HERE

12345

Before you Begin

Hardware and components are indicated with a balloon. Refer to the hardware tables that

accompany each step for corresponding size and type.

Be sure all hardware is tight before using the machine.

!

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 10 of 47

Included in this box:

-All Hardware

-Assembly Manual

-Weight Stack Labels

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 11 of 47

Carton Contents Box 1:

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 12 of 47

Tagged for use only

on Leg Ext/Curl

weight stack.

Carton Contents Box 2:

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 13 of 47

10 LB. Weight Plate Box

Part Number: B1602

Comprised of

(4) x 10 lb. Weight Plates

15 LB. Weight Plate Box

Part Number: B1603

Comprised of

(4) x 15lb. Weight Plates

OR

Weight Plate Cartons

Weight plates are packaged (4) per box. You should have (8) boxes of weights. This will

give you a total of 32 weight plates, (16) weight plates per stack.

The weight plates are available in two different sizes, 10 lbs. and 15 lbs. You may receive

a combination of the two weight plate sizes depending on your order.

Accessories

The following pieces are included in the Chest Station Box.

-Ab Strap

-Handle Strap

-Ankle Strap

-Chain Extension

-Straight Bar.

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 14 of 47

STEP 1: ASSEMBLE THE CHEST PRESS

1. Place upright frame and chest press

frame squarely on the floor.

2. Insert the pre-assembled cable from

the top of the chest press frame into

the upright as shown.

3. Insert the pre-assembled cable from

the bottom of the chest press frame

into the upright as shown.

4. Loosely assemble ALL hardware

shown in this step.

5. After aligning all component edges

and surfaces, tighten the hardware.

6. Install the rubber feet

Insert the pre-assembled

cables as far as possible

into the upright as

shown.

Threaded

cable end.

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 15 of 47

Strength

MP 2.0 & 2.5

STEP 2: ASSEMBLE THE PADS

1. Loosely assemble ALL hardware

shown in this step.

2. After aligning all component edges

and surfaces, tighten the hardware.

3. Be sure that both the Seat pad and

Back pad can adjust easily.

Note: The

adjustment

slots are in

front.

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 16 of 47

First, place the slot in the plate over

the stop peg, then rotate the arm

down to line up the axle housings.

1. To assemble the press arm, lift the

arm so that the stop peg fits into

the slot in the adjustment plate (as

shown). Then rotate the arm down

to line up the axle housings.

2. Insert the axle from either side of

the machine. You may need a

rubber mallet to install the axle.

3. After the axle is installed, tighten

the four set screws on the press

arm assembly.

4. Make sure arm can adjust easily.

TO INSTALL ARM

Tighten the four

set screws after

installation.

Installation may

require two people.

STEP 3: ASSEMBLE THE PRESS ARM

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 17 of 47

STEP 4: INSTALL CHEST PRESS CABLE

1. Shown on this page is the general

routing of the Chest Press cable

(P13-0167). The following pages

show sections in greater detail.

Attach cable after

weight stack is

installed.

This section of cable

comes pre-assembled

from the factory.

P13-0167

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 18 of 47

1. Route the Chest Press cable as

shown.

2. Install the pulleys and associated

hardware as you go along.

3. Make sure the cable and pulleys can

move freely. The cables must not get

routed around the cable retaining

bolts.

Make sure cable does not

route around the cable

retaining bolts.

Install this bolt after all the

other hardware and cable has

been installed.

Attach cable after weight

stack is installed.

Chest Press

Station

IMPORTANT !

A

3/16” CABLE

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 19 of 47

STEP 4: INSTALL CHEST PRESS CABLE

Strength

MP 2.0 & 2.5

Strength

MP 2.0 & 2.5

True Fitness Technology • O’Fallon, MO • Phone: 800-426-6570/636-272-7100 • Truetness.com

Page # 20 of 47

1. Shown on this page is the general

routing of the Low Pulley cable (P13-

0169). The following pages show

sections in greater detail.

2. The cable will be pre-installed into

the chest press station but will need

to be routed through the upright and

out the Low Pulley.

1. Shown on this page is the general

routing of the Low Pulley cable (P13-

0169). The following pages show

sections in greater detail.

2. The cable will be pre-installed into

the chest press station but will need

to be routed through the upright and

out the Low Pulley.

STEP 5: INSTALL THE LOW PULLEY CABLE

Page is loading ...

True Fitness MP 2.0 User manual

True Fitness MP 2.0 User manual

Related papers

Other documents