Toro Tensioned Fork Kit, Z Master Installation guide

Toro
Brand
Toro
Model
Tensioned Fork Kit, Z Master
Type
Installation guide

Toro Tensioned Fork Kit, Z Master: Enhance your mowing experience with this innovative kit designed to provide superior maneuverability and control for your Z Master. Effortlessly navigate tight spaces and maintain a precise cutting height, even on uneven terrain. The kit includes durable forks, caster wheel assemblies, and spacers, ensuring a smooth and efficient mowing operation. Experience the difference with Toro Tensioned Fork Kit, Z Master.

Toro Tensioned Fork Kit, Z Master: Enhance your mowing experience with this innovative kit designed to provide superior maneuverability and control for your Z Master. Effortlessly navigate tight spaces and maintain a precise cutting height, even on uneven terrain. The kit includes durable forks, caster wheel assemblies, and spacers, ensuring a smooth and efficient mowing operation. Experience the difference with Toro Tensioned Fork Kit, Z Master.

The T
oro Company – 1998
Printed in USA
All Rights Reserved
FORM NO. 3322–267
INSTALLATION
INSTRUCTIONS
Part No. 99–0285
Fork
T
ension Kit
Out Front Z
Loose
Parts
Note: Use the chart below to identify parts for assembly.
DESCRIPTION QTY. USE
Fork
Nut (from existing assembly)
Wheel (from existing assembly)
W
ashers (from existing assembly)
Bolt (from existing assembly)
Spacer (from existing assembly)
2
2
2
8
2
2
Install Caster Wheel
Cap
W
ashers (from existing assembly)
1/2” Spacer
1” Spacer (from existing assembly)
Caster Wheel Assembly
2
6
2
2
2
Install Caster Wheel Assembly
Installation Instructions
2
Remove
Existing Caster Wheel
Assembly
1. Disengage the power take off (PTO), set the
parking brake, and turn the ignition key to
“OFF” to stop the engine. Remove the key.
2. Flip up deck and lock into vertical position.
3. Remove existing hardware and caster wheel
assembly from deck frame.
Note: Keep three washers and the 1” spacer.
These parts are to be used with new
assembly.
Remove
and install Caster
Wheel
1. Remove hardware and caster wheel from
existing fork assembly. Discard fork.
2. Install caster wheel into new fork. Use existing
hardware to assemble (Fig. 1).
Install
new Caster Wheel
Assembly
1. Install fork assembly
, spacers and washers as
shown in figure 2. Use new and existing
hardware to assemble.
Note: There must be a washer installed
between cap and new spacer located on
the top of the assembly (Fig. 2).
2. Screw new cap onto assembly. Tighten until the
cap causes caster wheel assembly to turn (Fig.2).
3. During operation, periodically check cap and
tighten if necessary to maintain tension (Fig.2).
4. Repeat all procedures for other caster wheel.
4
1
2
6
5
4
3

Figure 1
1. Fork
(New)
2. Nut
3.
Caster Wheel
4. Washer
5. Bolt
6. Spacer
2
3
2
1
2
5
m–4182
4
Figure
2
1. Cap
(New)
2. Washer
3.
1/2”(13mm) Spacer (New)
4.
1” (26mm) Spacer
5.
Caster Wheel Assembly
(with new fork)
  • Page 1 1
  • Page 2 2

Toro Tensioned Fork Kit, Z Master Installation guide

Toro
Brand
Toro
Model
Tensioned Fork Kit, Z Master
Type
Installation guide

Toro Tensioned Fork Kit, Z Master: Enhance your mowing experience with this innovative kit designed to provide superior maneuverability and control for your Z Master. Effortlessly navigate tight spaces and maintain a precise cutting height, even on uneven terrain. The kit includes durable forks, caster wheel assemblies, and spacers, ensuring a smooth and efficient mowing operation. Experience the difference with Toro Tensioned Fork Kit, Z Master.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents