TREE ASSEMBLY & USE INSTRUCTIONS
Low Voltage Pre-lit Tree
THESE INSTRUCTIONS ARE FOR YOUR SAFETY. READ AND FOLLOW ALL INSTRUCTIONS AND
WARNINGS BEFORE USE.
Caution:
For INDOOR use only.
Keep away from flames and open fires.
Do not place over or near sources of heat.
This is a decoration, not a toy. Keep out of reach of young children and babies.
Please keep instructions for future reference.
Make sure that the wire cable has been unraveled before switching on.
Ensure that the cable does not pose a tripping or snagging hazard.
Do not operate this light set while still in its packaging.
Do not connect this chain of lights electrically to another chain of lights.
Be sure not to damage the cable or fittings.
If the cable is damaged, it cannot be repaired and the light set must be properly disposed of.
Do not allow any plastic part to come in contact with heat or an open flame.
Do not attempt to connect this light set directly to the main supply - only use with the
transformer adaptor provided.
This seasonal product is not intended for permanent installation or use.
Retain these instructions for future reference.
Assembly:
Quick Connect Pole is used to the tree, which make the assembly very easy.
Quick Connect Pole: The Tree is equipped with Quick Connect Pole! You need not to connect
more light strings as a normal tree. When you connect the poles, pls make sure the position of the
jack matches the socket to avoid damaging the internal connection device. ( Refer to the assembly
diagram)
Please follow these instructions carefully to ensure safe and satisfactory operation of the tree and
light set.
Please keep this instruction sheet for future reference.
1. Carefully remove the tree and lighting set from its packaging.
2. Make sure that the cable is completely unraveled and that there are no twists or snags in the
cable.
3. Position the cable so that it does not present a snagging or tripping hazard.
4. Please ensure that the plug-in adaptor is only plugged into the main supply indoor, not outdoor.
5. Assemble the tree stand near power outlet and place on a flat surface.
ASSEMBLY INSTRUCTION FOR TREE STAND
1. MATERIAL: TREE STAND , 3 EYE BOLTS
2. OPEN THE LEGS AT A 90 DEGREE ANGLE UNTIL THE HOLES ON TUBE MATCH.
3. INSERT 3 EYE BOLTS AND SCREW THEM INTO THE TUBE.
4. INSERT TREE TUBE INTO THE STAND, TIGHTEN THE EYE BOLTS TO SECURE TREE
6. Inset the bottom section（ Section C）of the tree to the tree stand.
7. Remove the bubble wrap and allow the hinged branches to unfold into place. Make sure all
wiring is free from the branch hinges. Shape the branches on the bottom section of your tree.
8. Insert the middle section (Section B) of the tree into the bottom section. Remove the bubble
wrap to allow the hinged branches to unfold into place. Make sure all wiring is free from the
branch hinges.
9. Insert the tree top (Section A). Remove the bubble wrap
and cord in order to shape the branches.
10. Shape the whole tree for a natural look.
11. Connect the light set to the transformer provided with
the product. Connect the transformer to standard outlet.
There is a foot pedal for controlling LED lights ON/OFF
function.
Bulb Replacement Instruction:
If a bulb is blown, please replace the faulty bulb by following
the below steps in diagram.
There are spare bulbs included for replacement.
Care & Use:
1. Before using or re-using, please inspect the product carefully. Do not use any products that have
cut, damaged or frayed wire insulation or cords, cracks in the lamp holders, loose connections or
exposed copper wire.
2. Before storing the product, please carefully remove the product from wherever it is placed to
avoid undue strain or stress on the product conductors, connections and wires.
Storage:
Carefully repack the tree in its box. STORE THE PRODUCT IN A COOL AND DRY LOCATION
PROTECTED FROM SUNLIGHT AND WHERE THE TEMPERATURE DOES NOT EXCEED 40˚C.
Trouble shooting:
If the product does not work properly, check these connections:
1. Make sure that the light string plugs are securely plugged.
2. Make sure the plug of the transformer is connected to the power supply.
3. Make sure the control box is switched on.
If none of the above steps corrects your problem, please contact the Customer Service
Department at Puleo International, Inc. :
CUSTOMER SERVICE CALL: +1 (800)-311-3324
EMAIL ADDRESS: [email protected]Business Hours: Monday - Friday - 9:30 am - 4:00 pm
EST
A
da
p
to
r
/
