Sunjoy 110101030 User guide

Brand: Sunjoy

Model: 110101030

Type: User guide

IMPORTANT:

Please read and follow all safety statements, warnings, assembly instructions, use &

care directions, before attempting to assemble.

1. When installing and assembling your gazebo, it is recommended that 4 or more adults are

involved.

2. Do not use the unit during an electrical storm, as there is a remote chance of getting struck

by lightning.

3. Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury,

possibly even death.

4. Do not leave the gazebo assembled when there is a risk of high wind, as possible damage

will occur to the structure.

5. Never barbecue under this gazebo or use lanterns that contain open flames.

6. This package contains small items and plastic bags that should be kept away from children.

7. Ensure that all connectors & poles are firmly secured fully in position. It is important to do so

before use so as to avoid collapsing or damage to the item, which could result in injury.

Tools required: ladder, hammer screwdriver (not included)

Assembly Instructions

Item#: L-GZ076PST-1B

Pole 1

Pole 2

Pole 3

Pole 4

Pole 5

Fence 1

Fence 2

Screen

Corner connector

Slant bar

Small top bar

Large top connecter

Small top connecter

Hook

Tracking Tube

Glass side bar top

Side bar top support (preassembled

on the side bar top K)

Peg fitting 1

Parts List

Peg fitting 2

Peg fitting 3

Small canopy

Top canopy

Bug netting

Finial decoration

Hardware Pack

M5×15 mm Screw

56PCS

M5 Flat Washer

56PCS

M6×30 mm Screw

8PCS

M6 Flat Washer

14PCS

M6 Nut

6PCS

Plastic Washer

4PCS

Stake

8PCS

Plastic Tie

48 PCS

M6 Wrench

1 PC

Fig 1.1

Fig 1.2

Fig.2

Step.1: Insert Fence 1(B1) into Pole2 (A2) and Pole 4 (A4) as Fig 1.1and Fig 1.2 showed; then insert

the other end of fence into Pole 5(A5) and Pole 3(A3), assemble Fence 2(B2) in the same way.

Step.2: Use screw (AA), flat washer (BB) to connect Peg fitting 3 (O) to Fence (B1) and Pole (A4 and

A2) (Fig.2). Assemble Peg fitting 2 (N) to Fence (B2) and Pole 1 (A1) in the same way.

Step.3: Use screw (AA), flat washer (BB) to connect Peg Fitting 1(M) to Fence (B1 and B2) and Pole

(A3 and A5) (Fig.3).

Step.4: Use screw (AA), flat washer (BB) to fix Tracking Tube (J) to the Screen (C) (Fig.4).

Step.5: Install the Screen (C) to the Pole (A4/A1/A2/A3/A5) with its own pin (Fig.5).

Step.6: Use screw (AA), flat washer (BB) to fix Corner connector (D) to the Pole (A4/A1/A2/A3/A5) and

Screen (C) (Fig.6).

Step.7: Insert Slant bar (E) to Large top connecter (G); and twist Hook (I) to Large top connecter (G)

(Fig.7). (Note: the end near the hole of Slant bar (E) should be in the above)

Step.8: Insert Corner connector (D) to Slant bar (E) (Fig.8).

Fig.3

Fig.5

Fig.6

Fig.4

Fig.7

Fig.8

Step.9: Insert Small top bar (F) to Small top connecter (H) (Fig.9).

Step.10: Assemble the small canopy (P) on small top frame (Fig.10).

Step.11: Rotate the Finial decoration (S) to the screw bar of small top (H) (Fig.11).

Step 12：Assemble the Top canopy (Q) on top frame (do not tighten) (Fig.12).

Step.13: Use screw (CC), flat washer (DD) and nut (EE) to fix Small top bar (F) to Slant bar (E)

(Fig.13), securing all the screw with Wrench (JJ).

Step.14: Use screw (CC), flat washer (DD) and Plastic Washer (FF) to fix Glass side bar top

(K) to the Pole (A3/A4),then fix Side bar top support (L) to the Pole(A3/A4) with its own

chain bolt(Fig.14).

Fig.9

Fig.13

Fig.11

Fig.10

Fig.14

Fig.12

Step 15：Insert Stake (GG) into Peg fitting 1/2/3(M/N/O) from up to bottom (Fig.15).

Step 16：Hang the Netting (R) to Tracking Tube (J) with Plastic Tie (HH), (Fig.16).Lastly fully

assembled the canopy (Q).

Now the gazebo is ready for use.

Fig.15

Fig.16

USE & CARE:

1. This Gazebo is not a permanent structure and should be disassembled & stored away after

use.

2. Do not repack your gazebo until completely dry.

3. This Gazebo must be assembled by Four adults or more.

4. This Gazebo must not be left erect in windy conditions.

5. Loading limit of the hook is 45 lbs.

6. Loading limit of the ring is 25 lbs.

7. Loading limit of the glass side bar top is 33 lbs.

WARNINGS:

1. Assembly Instructions must be followed.

2. Pegs supplied must be used to hold this gazebo in place when upright.

3. Warranty does not cover damage due to extreme weather conditions.

4. Do not use candles, matches or open flames of any kind in or near a tent.

5. Do not cook inside the tent.

6. Build campfires downwind and several meters away from a tent and be sure to fully

extinguish campfires before leaving a campsite or before retiring for the night.

7. Exercise extreme caution when using fuel-powered lanterns or heaters inside a tent and use

battery-operated lanterns whenever possible.

8. Do not refuel lamps, heaters or stoves inside a tent.

9. Extinguish or turn off all lanterns before going to sleep.

10. Do not smoke in a tent.

11. Do not store flammable liquids inside a tent.

12. KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent is

made of flame-resistant fabric. It is not fireproof. The fabric will burn if left in continuous contact

with a flame source.

Limited Warranty:

This limited warranty is extended to the original purchaser and applies to defects in materials

and workmanship of your item provided the item is maintained with care and used only for

personal, residential purposes. The item is warranted to be free from defects in material or

workmanship for a period of one (1) year. We don't reimburse for transportation or

delivery costs, or compensate the individual or any outside party for assembling or

disassembling the product.

Exclusions:

Items used for commercial, contract, or other non-residential purposes, or items damaged due

to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or

rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for

warranty claims. Warranty is to the original purchaser and is non-transferable. Any

replacement of warranted items will be in the original style and color, or a similar style and

color if the original is unavailable or has been discontinued. As some states do not allow

exclusions or limitations on an implied warranty, the above exclusions and limitations may not

apply. This warranty gives you specific rights, and you may also have other rights, which vary

from state to state.

Maintenance:

Our iron/steel components for garden accessories and patio items are coated with rust

inhibiting paint that protects it from rusting. However, due to the nature of iron, surface

oxidation (rusting) will occur once these protective coatings are scratched. This is a natural

process and is not a defect! To minimize this condition, we recommend care when assembling

& handling the product to prevent scratching the paint. Should any scratching or damage

occur, we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be

easily removed with a very light application of common cooking oil. If surface oxidation

(rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping on

to deck or patio and cause damaging stains, which may be difficult to remove. This can be

prevented if measure is taken to keep the product from oxidizing.

Important: Please do not return this product to the store. For technical assistance on

assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am

EST to 8:00 pm PST or fax the replacement part form which is in the box to 1-740-283-3549 or

Email custom[email protected] for assistance.

Made in China

2016-4

Sunjoy 110101030 User guide

Brand: Sunjoy

Model: 110101030

Type: User guide

Download PDF

report

Sunjoy 110101030 User guide

Sunjoy 110101030 User guide

Related papers

Other documents