Gazebo Penguin 41218-12 Operating instructions

Brand: Gazebo Penguin

Model: 41218-12

Type: Operating instructions

Gazebo Penguin 41218-12 is a 4 seasons outdoor construction designed for added living space. It's easy to assemble and its aluminum frame makes it a rust-resistant and durable outdoor addition. Gazebo Penguin 41218-12 can withstand most weather conditions, but it's important to keep the roof free of snow accumulation and avoid placing it near trees or sloped roofs, as the snow and ice may slide onto the roof and cause it to collapse. If you wish to suspend products to the structure, ensure that the total weight does not exceed 6.8 kg (15 pounds).

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 1

41218 MR

12 X 18 SOLARIUM

ASSEMBLY INSTRUCTIONS

Three adults required for assembly

Base Dimensions 12’ ½”x18’11”

Largest Dimensions 13’6”x20’4½”

Overall Height 110’’

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 2

Before you assemble the Solarium

 Some jurisdictions may require permits for, or otherwise regulate, installation of

use of temporary structures. Consult with your governing authority or

municipality codes before assembly.

 Please don't destroy boxes until completely assembled.

 It is important that this solarium be installed on a solid base with the provided

screws. Otherwise, please ensure that you use anchors sufficient for your surface.

 The solarium should not be installed adjacent to trees or a sloped roof. Snow and

ice may slide onto the solarium and cause it to collapse.

Tools needed:

 Step ladder

 #2 Phillips screwdriver (supplied)

 Rubber mallet

Based on the location, decide where you would like to position the two (2) doors panels

which can slide open to the left or the right, your choice.

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 3

12x18 Solarium Assembly Instructions

Step 1:

Before starting to assemble, please decide where you would like to position the door panels.

1. Stand up two regular frames (A1), using two connecting pieces (E) and affix the panels (A1)

together.

2. Stand up a frame meant to be next to the door (A2) and a door frame (B2), placing the door frame

either on the left or right, then use two connecting pieces (E) to affix the panel and door frame.

3. When assembling angled panels (A1), you should put the two panels at 135 degree angle then use

the angled connecting pieces (I) and (J) to affix the panels together.

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 4

Step 2:

1. Slide top door rail (F) into wheels of sliding door.

2. Slide lower door rail (G) into the plastic guide of the sliding door (B1).

3. Use bold (Bb) to affix the plastic stoppers (H) one on each end of top door rail (F).

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 5

Step 3:

Please note the sliding door should be installed from the inside of the solarium.

1. Place a bolt (Hh) and washer (Gg) through the top door rail (F) and door frame, and place a female

bolt (Cc) from the other side. Once all are inserted, tighten them all securely.

2. Secure the bottom door rail (G), using a bolt (Cc) with a washer (Gg).

3. Paying careful attention to whether it is the left (Dd-L) or right (Dd-R) latch, use bolt (Bb) to affix

the door latch onto the frame.

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 6

Step 4:

Note: Rafters must be affixed where panels connect to each other.

1. Attach roof rafters (L2) to the central hub (J1) using bolt (Bb).

2. Use screw (Z) to affix the rafters (L2) onto the top of panels going through the metal piece

attached to the rafter (L2).

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 7

Step 5:

Note: Do not tighten the bolts right away as you may have to adjust the angle when inserting the

roof panels.

Use the same method to assemble roof rafters (L1) for the angled panels.

The rafters (L1) should be affixed to the mounting bracket using the hole that will be furthest away from

the corner of the unit.

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 8

Step 6:

Use nut (Hh) and washer (Gg) to affix the top cap (K1) to the central hub (J1).

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 9

Step 7:

1. Secure the side of the roof with finishing bar (M) with a screw (S1).

2. Place a roof finishing bar (M) next to the right of the roof finishing bar (M) and align the

pre-drilled holes in each bar one on top of the other.

Place finishing end (Q) over the aligned holes and secure with screw (S1).

3. Repeat process with all finishing bars as illustrated.

4. In order to finish the installation of the last finishing bar (M1) you have to unscrew the first

screw (S1) at your starting point and place a finishing end (Q) then re-install the screw (S1).

Note: the finishing ends change depending on where you are along the unit.

Always refer to the illustration.

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 10

Step 8:

From the inside of the solarium, install the solidifying bar (N and N1) as illustrated using the screws (V).

Each screw (V) must be inserted into two pre-drilled holes prior to be screwed to the roof bars.

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 11

Step 9:

Insert the upper panels (Qq, R1a, Qa, Ra)

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 12

Step 10 :

After the installation on the upper roof panels, install the bottom roof panels (Rr, R1b, Qb, Qc, Rb)

according to below drawings.

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 13

Step 11:

Once the installation of the panels is complete, screw cover roof bars (O/O1) to the roof bars

(L1/L2) with screw (U).

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 14

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 15

12X18 Solarium

DESCRIPTION

DRAWING

DESCRIPTION

DRAWING

17-081

REGULAR

FRAME

17-083

FRAME NEXT

TO DOOR

(with extra holes)

17-085

SLIDING DOOR

RIGHT

17-086

SLIDING DOOR

LEFT

08-133-12

CONNECTING

PIECE

Length 200.6 cm

08-136-12

TOP DOOR RAIL

Length 208 cm

08-137-12

BOTTOM DOOR

RAIL

Length 205.6 cm

08-138-12

PLASTIC

STOPPER

08-139-12

135° ANGLED

OUTSIDE

CONNECTOR

Length 200.6 cm

08-140-12

135° ANGLED

INSIDE

CONNECTOR

Length 200.6 cm

17-044-12

ROOF RAFTER

Length 199 cm

17-043-12

ROOF RAFTER

Length 224.4 cm

08-179-18

TOP CAP

08-178-18

CENTRAL HUB

17-047-12

MIDDLE

ROOF JOINT

Length 71 cm

17-048-12

MIDDLE ROOF

JOINT

Length 72 cm

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 16

17-053

FINISHING END

12-037-12

FEMALE BOLT

Cc-2

17-072

(24 ¼”X42 ¼”)

TOP ROOF

LEFT PANEL

R1a

08-156-12

SCREW

17-068

(24 ½”x46 ½”)

TOP ROOF

CORNER

PANEL

08-158-12

BOLT

08-161-12

BOLT

08-165-12

RIGHT DOOR

LATCH

Dd-R

08-169-12

LEFT DOOR

LATCH

Dd-L

08-167-12

SCREW

08-168-12

BOLT

08-187

WASHER

08-189-12

ACORN NUT

08-193

PLASTIC PLUG

17-069

(47”x47 ½”)

BOTTOM ROOF

CORNER PANEL

17-073

(46 ¼”x43”)

BOTTOM ROOF

LEFT PANEL

R1b

17-070

(24 ¼”x42 ½”)

TOP RIGHT

ROOF PANEL

17-071

(46 ¼”x43”)

BOTTOM ROOF

RIGHT PANEL

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 17

08-135-12

SCREW

12-047-12

VIS

(M5*15mm)

17-076

(41 ¼”x43”)

BOTTOM ROOF

CENTER PANEL

17-075

(41 ¼”x42 ¼”)

TOP ROOF

CENTER PANEL

17-079

BOTTOM

ALUMINIUM

PANEL (for wall

panels)

17-080

BOTTOM

ALUMINIUM

PANEL (for

doors)

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 18

L:\WP51\INSTRUCTIONS\SOLARIUMS INSTRUCTION BOOKS\41218 MR\ZZZ-184.41218MR.0926-16.GP.EN.doc SUN-HP 19

MAINTENANCE NOTES

1. Check all the screws for tightness before and during usage of the unit.

Tighten the screws at least twice a year.

2. If you wish to suspend products to the structure, ensure that the total weight of articles

does not exceed 6,8 kg (15 pounds). Suspend nothing from the structure in case of

strong winds as well as during the winter.

3. In case of a defective or damaged part, or for any other questions concerning the

product, please contact the manufacturer directly.

4. Please have the parts list and part numbers on hand when ordering or requesting

replacement parts.

5. The product should not be installed adjacent to trees or a sloped roof. Snow and ice

may slide onto the roof and cause it to collapse.

6. While the product is designed for 4 seasons use, the roof must be kept free of

accumulation of snow.

ONE YEAR LIMITED WARRANTY

This product has been designed and manufactured to meet the highest standards of quality and

durability. Subject to the Conditions for Exercising the Warranty and the Limitations on the

Warranty set forth below, it is warranted to be free of material and manufacturing defects for a

period of one year from the date of purchase. Should the product become damaged, or the

warranty period has expired, please contact Adlonco Holdings Customer Service Department

for a complete schedule of replacement parts and prices.

CONDITIONS FOR EXERCISING THE WARRANTY

The warranty only applies to the original purchaser with the bill.

In order to properly exercise your warranty, please comply with the following:

Carefully inspect the contents of the carton for missing or damaged components.

Should you discover damaged or missing parts, do not return the product to the

place of purchase, but contact Adlonco Holdings Customer Service Department at the

numbers listed below:

Montreal: (514) 276-3485 Elsewhere: 1-800-737-7174

NOTE: Damages/missing parts must be reported within 30 days of delivery.

LIMITATIONS ON THE WARRANTY

1. The product is not warranted against damages due to vandalism, abuse, falling or

thrown objects, or accumulation of snow.

2. The product is not warranted against damages due to extreme weather conditions,

such as thunderstorms, hail, strong wind or snow storms, or any other acts of God.

3. The product is only warranted in the event it is installed in accordance with the A’s

written instructions enclosed with the product.

4. The product is not warranted in the event it has been improperly anchored.

5. We reserve the right to replace or repair any defective product or parts at our discretion.

Gazebo Penguin 41218-12 Operating instructions

Brand: Gazebo Penguin

Model: 41218-12

Type: Operating instructions

Download PDF

report

Gazebo Penguin 41218-12 Operating instructions

Gazebo Penguin 41218-12 Operating instructions

Related papers

Other documents