SkyLink SA-001S User manual

Brand: SkyLink

Model: SA-001S

Type: User manual

SkyLink SA-001S

The SkyLink SA-001S is a wireless outdoor solar siren that can be programmed to sound an alarm when triggered by a compatible sensor or remote control. It is powered by a rechargeable battery pack that is charged by the sun's rays, so there is no need to worry about replacing batteries. The SA-001S is also equipped with a backup battery compartment that can be used to power the siren in the event of a power outage.

Some of the features of the SA-001S include:

Solar powered with a backup battery compartment
Wireless operation with a range of up to 200 feet
Easy to install and program

SkyLink SA-001S

Some of the features of the SA-001S include:

Solar powered with a backup battery compartment
Wireless operation with a range of up to 200 feet
Easy to install and program

Wireless Outdoor Solar Siren

SA-001S

User Manual

4x Mounting Accessories

1x Wireless Outdoor Solar Siren

(SA-001S)

1x Rechargeable Battery Pack

3x AA Alkaline Batteries

1. Package Contents

2. Technical Specifications

Fig. 1 Inside SA-001S

Fig. 4 Back Detail

Fig. 3 Detail, LED Board

Fig. 2 Detail, Motherboard

Rechargeable Battery pack

Solar Panel

Backup Battery

Compartment

DC Jack

“LEARN/SET”

LED

Power

“PWR” LED

“ALKALINE”

connector

"SOLAR" Panel

Connector

"SIREN" Speaker

Connector

“NiMH”

connector

“LEARN/SET”

Button

Tamper Protection

security

Mounting Screws

holder

3. Installation

1. Unscrew and open the Solar SA-001S (Fig. 5 ).

2. Insert 3xAA Alkaline batteries (Fig. 1).

3. Insert the rechargeable battery pack wire into the black connector “NiMH” (Fig. 2).

4. The “LEARN/SET” LED (Fig. 3) will turn on for 1 second and then off.

5. The “PWR” LED (Fig. 3) will keep flashing.

Fig. 5 Detail, Screws

For Model SA-001A Only: Plug in the optional AC adapter to an AC outlet and the

other end into the DC jack of the unit. The "PWR" LED indication will stay on.

The adaptor as a disconnect device. The socket-outlet shall be installed near the

equipment and shall be easily accessible.

4. Programming with SkylinkNet Alarm System

Tap “Siren/External

Alarm/Dialer”

•••More” 2.

Tap “System

Settings”

3. Tap “Set-up

Wizard”

4. Tap “Add

Device”

6. On the SA-001S,

press and hold

“LEARN/SET”

button (Fig. 2);

the

“LEARN/SET”

LED (Fig. 3) will

flash.

8. On the SA-001S,

the “PWR” LED

(Fig. 3) will flash

and beep twice if

it’s programmed

successfully.

Tap “LEARN

NOW”

Tap “

5. Programming the SC-Series Alarm System

1. On the SA-001S, press and hold the "LEARN/SET"

button for 2 seconds and then release. The

"LEARN/SET" LED (Fig. 3) will flash.

2. On the SC-001 control panel, enter

your Master Pin [factory default 000];

then press the “B” key twice.

3. On the SA-001S, you will hear 2 beeps and

the LED will flash twice indicating that the

SC-001 has been programmed successfully.

Control Panel

“LEARN/SET” LED

“LEARN/SET” Button

6. Programming the M-Series 2in1 Alert/Alarm System

1. On the SA-001S, press and hold the "LEARN/SET"

button for 2 seconds and then release. The

"LEARN/SET" LED (Fig. 3) will flash.

2. On the M-1 console, press and

hold the "MUTE" [located on the

rear] button for 5 seconds.

“MUTE” button

“LEARN/SET” LED

“LEARN/SET” Button

3. On the SA-001S, you will hear 2 beeps and

the LEDs will flash twice indicating that the

M-1 has been programmed successfully.

7. Programming the Alarm Sound Duration

User can customize the alarm period from 30 seconds up to 10 minutes.

The factory default is 3 minutes.

1. On the SA-001S, press and hold the "LEARN/SET" button for 5

seconds; you can release the "LEARN/SET" button while all the PWR

and "LEARN/SET" LEDs (Fig. 3) turn on.

2. While all the LEDs are lit, press the "LEARN/SET" button once, the

LEDs flash once indicating the alarm period is set to 30 seconds.

3. To customize/change the alarm period, continue to press the

"LEARN/SET" button. Refer to the Table 1 (below).

The LEDs will flash corresponding to the number of times you pressed

the "LEARN/SET" button.

4. Press and hold the "LEARN/SET" button to confirm your setting. You

will hear 2 beeps and the LEDs will flash twice indicating the alarm

period is now programmed to the unit.

“LEARN/SET”

Button

# "LEARN/SET" button pressed Alarm Period

1 30 seconds

2 60 seconds

3 3 minutes

4 5 minutes

5 10 minutes

Table 1, # "LEARN/SET" pressed to Alarm Period

8. Solar Power Installation

The SA-001S is equipped with a solar panel (Fig. 1)

on top of the cover. During the day, it charges the

rechargeable battery pack. During the night, the

pack operates the unit.

1. Unplug the NiMH & Alkaline Connector (Fig. 2 ).

2. Install unit outside the premise with the mounting

materials included (see Package Content).

3. Connect the NiMH, Alkaline connector and close

the cover with the screws (Fig. 5).

The unit should be installed outside of the premise and facing the East, West or South

(most optimal) side. Avoid the North side and any shadows cast by walls, trees and roof

overhangs to the unit. (Fig. 6)

The SA-001S is built-in with Tamper Protection (Fig. 4) for security system. The

system is activated after the unit is mounted. If you remove the cover or move the unit to

another location then the system will alarm.

Please disarm the unit before you replace the battery or before you conduct any kind of

service maintenance, i.e. checking or cleaning the unit.

WEST EAST

SOUTH

NORTH

Fig. 6 Installation

9. Replacing the Battery

For back-up, the SA-001S uses 3xAA Alkaline batteries. If the batteries are low, the unit will emit 3

beeps when the remote arms or disarms the unit. Replace all of them at the same time or recharge (if

using rechargeable battery only):

1. Remove the cover of the SA-001S (Fig. 5).

2. Replace old batteries with new ones in battery compartment (Fig. 1). Beware of the battery polarity.

3. Replace the cover.

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT

TYPE. DISPOSE USED BATTERIES ACCORDING TO MANUFACTURER'S

INSTRUCTIONS.

9. Replacing the Battery

Your SA-001S requires few simple maintenance to ensure its continued reliability and operation.

- The solar panel on the top housing should be cleaned using a soft damp cloth. This will ensure the

solar panel receives all the available light.

- Test The unit periodically to ensure it is working.

10. Maintenance

11. FAQ

A. You must program the sensor or remote to the SA-001S before they can work together [Section

5 and 6].

A. Ensure none of the sensors are triggered, i.e. the door or window sensor should be in close

status

A. You have set the Alert Notification Jumper to ‘Disable’, this will disable the beeping. Reset this

jumper to ‘Enable’ to hear the beeping.

A. You cannot erase just one sensor or one remote form the unit. You must erase all sensors or

remote and then program the ones that you want to keep.

A. The SA-001S will function properly if there is an AC power (model SA-001A only), even without

the backup batteries. The backup batteries provide power when there is no AC power, e.g. during

power failure.

Why is the SA-001S not responding to the sensor or remote?

Why can’t I arm the system?

Why isn’t the SA-001S alarm beeping yet the lights are all flashing?

How can I erase just one sensor or one remote from the SA-001S?

Will the SA-001S alarm function properly if no back-up batteries are installed?

12. Safety Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

Reoriented or relocate the receiving antenna

- Increase the separation between the equipment and receiver

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

- Consult the dealer or an experience radio/TV technician for help

13. One Year Warranty / Customer Service

P/N:101Y035-002

This product is guaranteed to be free of defects in materials and workmanship for 1 year

from the date of purchase. If this product is defective, call 1-800-304-1187 for repair or

replacement parts. Guarantee does not include normal wear and tear or batteries.

If you have any questions, problems or missing parts,

please call Skylink Customer Support

1-800-304-1187

9:00 AM – 5:00 PM EST, Monday-Friday

Or e-mail us at [email protected]

www.skylinkhome.com

SkyLink SA-001S User manual

Brand: SkyLink

Model: SA-001S

Type: User manual

SkyLink SA-001S

Some of the features of the SA-001S include:

Solar powered with a backup battery compartment
Wireless operation with a range of up to 200 feet
Easy to install and program

Download PDF

report

SkyLink SA-001S User manual

SkyLink SA-001S User manual

Related papers

Other documents