C2G 37003 Owner's manual

C2G
Brand
C2G
Model
37003
Type
Owner's manual

This manual is also suitable for

Mounting the enclosure: (see Fig. 1)
1. Using the mounting tabs or side slots to mount the
enclosure between the stubs, or using mounting holes
provided in the back of the unit for surface mounting.
Note - Be sure to leave enough space both on the top
and bottom of the unit for wire routing and the "UP"
arrow should face to the top.
2. When using the side slots, position the enclosure with
the front to protrude beyond the wallboard surface,
which will match the finished wall. Mark the center
of the mounting slots, this allows for further adjustment
to match the finished wall. Drill pilot holes and install
the enclosure with wood screws. When using the
mounting tabs, select the proper holes (A-5/8", B-1/2"
or C-3/8") for wallboard. When using the mounting
holes, attach the unit to the wall with screw anchors
recommended to support the weight of the enclosure
and variety of modules.
Remove the knockouts for wiring: (see Fig. 2)
Remove the knockouts which can be found on the top,
bottom, sides and back of the enclosure as needed for
wiring. Insert a screwdriver into the slot and bend to
break the knockout. Insert the plastic grommets in the
opening to protect cables from being damaged.
G ND
C - 3/8"
B - 1/2"
A- 5/8"
Installing the cover: (see Fig. 4)
Hook the cover on the enclosure then screw it via
mounting holes on the cover.
2.0 in
1.5 in
8
7
OUT PU T
EX PA NS ION
TO LO CAT IO NS
4
5
6
Bridged T eleco m Module
HB g-1008
SE C UR IT Y
EmC om
ON
1
2
OFF
3
FR OM S OUR C E
RJ 31X
50W DC P ower s upply
EmC om
HDp-10 60
DC 7.5V
DC 12VDC 12VDC 12V
DC P OW E R OUT P UT
43
IR Dis tribution Module
HIr-10 04
4
32
EX PA NS ION
OUT PU T
12VD C
PO WE R
ON
ACT IV ITY
1 2
E mCom
1
From Loca tion
Se nsitivity Adjus tment
To Sourc e
Patch Pa nel Module
LOC AT ION
FR OM
HP p-1008EmC om
7
6
5
LOC AT ION
TO
4
3
8
1
2
5 P ort E therent HU B HUb-1 005
EmC om
2
R
R
LOC AT ION
TO
R
8
R
OUT
OUT
HVs -100 8
LL
1
3
R
LL
5
R
R
L L
PO WE R
12VD C
PO WE R
FR OM S OUR C E
R
L
SE NS IT IV ITY
ADJ US TME N T
EmC om
Module
Audio Dis tribution
L
7
L
R
OUT
IN
OUT
OUTOUT
OUTOUT
HAa -1016
EmC om
6
4
1 T o 8 V ideo S plitter Module
AC Powe r Module HPm- 1004
EX PA NS ION
HTe -1008
OUT PU T
8
6
7
4
5
TO LO CAT IO NS
2
3
1
FR OM S OUR C E
EmC om
Telecom Distribution module
EmC om
Wire ties: (see Fig. 5)
Using the provided wire ties to group and attach
the wires at the side grids of the enclosure.
Module Installation: (see Fig. 6)
There are many kinds of modules available to build up the HWS. To install the module, simply insert tabs
to the cap located on the rail of the enclosure. Press the fastener to lock the module at the desired position.
For easily wire routing, 1.5" interval and 2" interval is recommended
for data/voice modules and video modules respectively.
Fig. 4
Fig. 6
UP
Fig. 5
  • Page 1 1
  • Page 2 2

C2G 37003 Owner's manual

C2G
Brand
C2G
Model
37003
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents