ESAB Rogue ET 200iP PRO User manual

Brand: ESAB

Model: Rogue ET 200iP PRO

Category: Welding System

Type: User manual

ESAB Rogue ET 200iP PRO is an inverter-based power source for MMA (Manual Metal Arc) and TIG (Tungsten Inert Gas) welding, including HF TIG (High Frequency Tungsten Inert Gas) welding. It delivers precise arc control and stable performance, making it suitable for a wide range of welding applications. The Rogue ET 200iP PRO features intuitive controls, allowing you to easily set and adjust welding parameters.

Rogue

Instruction manual

0463 712 101 GB 20210224

Valid for: HA027-xxxx-xxxx

ET 200iP PRO

TABLE OF CONTENTS

0463 712 101 © ESAB AB 2021

SAFETY

.......................................................................................................

1.1 Meaning of symbols

...............................................................................

1.2 Safety precautions

.................................................................................

INTRODUCTION

..........................................................................................

2.1 Equipment

...............................................................................................

TECHNICAL DATA

......................................................................................

INSTALLATION

............................................................................................

4.1 Location

...................................................................................................

4.2 Lifting instructions

.................................................................................

4.3 Mains supply

...........................................................................................

OPERATION

................................................................................................

5.1 Overview

.................................................................................................

5.2 Connections and control devices

.........................................................

5.3 Connecting welding and return cables

................................................

5.4 Turning the power on/off

.......................................................................

5.5 Fan control

..............................................................................................

5.6 Thermal protection

.................................................................................

5.7 Functions and symbols

.........................................................................

5.8 Setting panel

...........................................................................................

5.9 Remote control

.......................................................................................

MAINTENANCE

...........................................................................................

6.1 Routine maintenance

.............................................................................

6.2 Cleaning instruction

...............................................................................

TROUBLESHOOTING

.................................................................................

ORDERING SPARE PARTS

........................................................................

DIAGRAM

............................................................................................................

ORDERING NUMBERS

.......................................................................................

ACCESSORIES

...................................................................................................

Rights reserved to alter specifications without notice.

1 SAFETY

0463 712 101

- 4 -

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and

Safety Data Sheets (SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0463 712 101

- 5 -

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

If equipped with ESAB cooler

Use ESAB approved coolant only. Non-approved coolant might damage the equipment and

jeopardize product safety. In case of such damage, all warranty undertakings from ESAB

cease to apply.

Recommended ESAB coolant ordering number: 0465720002.

For ordering information, see the "ACCESSORIES" chapter in the instruction manual.

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or work

cable around your body. Keep welding power source and cables as

far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

1 SAFETY

0463 712 101

- 6 -

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

HOT SURFACE - Parts can burn

• Do not touch parts bare handed.

• Allow cooling period before working on equipment.

• To handle hot parts, use proper tools and/or insulated welding gloves to

prevent burns.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be

potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations,

due to conducted as well as radiated disturbances.

1 SAFETY

0463 712 101

- 7 -

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on

Waste Electrical and Electronic Equipment and its

implementation in accordance with national law,

electrical and/or electronic equipment that has reached

the end of its life must be disposed of at a recycling

facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved

collection stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

0463 712 101

- 8 -

2 INTRODUCTION

Overview

Rogue ET 200iP PRO is an inverter-based power source intended for MMA (Manual Metal

Arc) and TIG (Tungsten Inert Gas) welding, HF TIG (High Frequency Tungsten Inert Gas)

welding.

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of

this manual.

2.1 Equipment

Rogue ET 200iP PRO includes:

• Power Source

• Work Clamp Leadset

• TIG Torch

• Gas Hose

• Safety Manual

• Quick Setup Guide

3 TECHNICAL DATA

0463 712 101

- 9 -

3 TECHNICAL DATA

Technical data

Rogue ET 200iP PRO

Outlet voltage 230V±15%

1~ 50/60Hz

115V±15%

1~ 50/60Hz

Primary current

max

MMA

30A 29A

max

TIG

19.5A 24A

No-loadpowerdemand when in

energy-saving mode 50W 50W

Setting range

MMA 20-200A 20-110A

TIG 10-200A 10-140A

Permissible load at MMA

25% duty cycle 200A/ 28V 110A/24.4V

60% duty cycle 129A/ 25.2V 70A/ 22.8V

100% duty cycle 100A/ 24V 55A/ 22.2V

Permissible load at TIG

25% duty cycle 200A/ 18V 140A/ 15.6V

60% duty cycle 129A/ 15.2V 90A/ 13.6V

100% duty cycle 100A/ 14V 70A/ 12.8 V

Apparent power I

at maximum current

6.9kVA 3.3kVA

Active power I

at maximum current

6.8kW 3.26kW

Power factor at maximum current

TIG 0.99 0.99

MMA 0.99 0.99

Efficiency at maximum current

MMA 82% 85%

TIG 82% 85%

Open-circuit voltage U

max

VRD 35 V deactivated 78V 78V

VRD 35 V activated <30V <30V

Operating temperature -10to +40°C

(+14to 104°F)

-10to+40°C

(+14to 104°F)

Transportation temperature -20 to +55°C

(-4 to +131°F)

-20 to +55°C

(-4 to +131°F)

Continual sound pressure at no-load <70dB <70dB

Dimensions l×w×h 403×153×264mm

(15.9×6×10.4in.)

Weight 9.6kg

3 TECHNICAL DATA

0463 712 101

- 10 -

Rogue ET 200iP PRO

Insulation class transformer H

Enclosure class IP23S

Application class

Mains supply, S

sc min

Minimum short circuit power on the network in accordance with IEC 61000-3-12.

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or

cut at a certain load without overloading. The duty cycle is valid for 40°C/104°F, or below.

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration

by solid objects or water.

Equipment marked IP23S is intended for indoor and outdoor use; however, should not be

operated in precipitation.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

4 INSTALLATION

0463 712 101

- 11 -

4 INSTALLATION

The installation must be carried out by a professional.

CAUTION!

This product is intended for industrial use. In a domestic environment this product may

cause radio interference. It is the user's responsibility to take adequate precautions.

4.1 Location

Position the power source so that cooling air inlets and outlets are not obstructed.

A. Minimum 200 mm (8 in.)

B. Minimum 200 mm (8 in.)

WARNING!

Secure the equipment - particularly if the ground is uneven or sloping.

4.2 Lifting instructions

These units are equipped with a handle for carrying purposes.

WARNING!

Electric shock can kill. Do not touch live electrical parts. Disconnect input power

conductors from de-energized supply line before moving the welding power source.

WARNING!

Falling equipment can cause serious personal injury and equipment damage.

Lift the unit with handle on top of case.

4 INSTALLATION

0463 712 101

- 12 -

4.3 Mains supply

NOTE!

Rogue ET 200iP PRO complies with IEC 61000-3-12 provided that the short-circuit

power is greater than or equal to S

scmin

at the interface point between the user's

supply and the public system. It is the responsibility of the installer or user of the

equipment to ensure, by consultation with the distribution network operator if

necessary, that the equipment is connected only to a supply with a short-circuit power

greater than or equal to S

scmin

. Refer to the technical data in the TECHNICAL DATA

chapter.

The power source will automatically adjust to the supplied input voltage. Make sure that it is

protected by the correct fuse rating. A protective ground connection must be made, in

accordance with regulations.

Rating plate with supply connection

data.

Recommended fuse sizes and minimum cable area for the ET 200iP PRO

Supply voltage 230VAC 115VAC

Electrical cable area 2.5mm

2.5mm

Maximal current rating I

max

MMA/Stick (SMAW) 30A 29A

4 INSTALLATION

0463 712 101

- 13 -

Recommended fuse sizes and minimum cable area for the ET 200iP PRO

I1eff MMA/Stick (SMAW) 15A 14.5A

Fuse anti-surge type D MCB 20A 20A

Recommended fuse sizes and minimum cable area for the ET 200iP PRO

Supply voltage 230VAC 115VAC

Maximum recommended

extension cord length 100m(328ft) 100m(328ft)

Minimum recommended

extension cord size 4mm

4mm

NOTE!

Different variants of Rogue ET 180i, ET 200i, ET 200iP PRO are certified for

different outlet voltages. Always refer to the rating plate for the specification of the

power source in use.

NOTE!

Use the power source in accordance with the relevant national regulations.

Supply from power generators

The power source can be supplied from different types of generators. However, some

generators may not provide sufficient power for the welding power source to operate

correctly. Generators with Automatic Voltage Regulation (AVR) or with equivalent or better

type of regulation, with rated power of 7 kW are recommended.

5 OPERATION

0463 712 101

- 14 -

5 OPERATION

5.1 Overview

General safety regulations for handling the equipment can be found in the "SAFETY"

chapter of this manual. Read it through before you start using the equipment!

NOTE!

When moving the equipment use intended handle. Never pull the cables.

WARNING!

Electric shock! Do not touch the workpiece or the welding head during operation!

5.2 Connections and control devices

1. Setting panel 5. Mains power supply switch, I/O

2. Positive welding terminal 6. TIG Switch / Remote Socket

3. Negative welding terminal 7. Gas supply output

4. Power cable 8. Gas supply input

5.3 Connecting welding and return cables

The power source has two outputs, a positive welding terminal (+) and a negative welding

terminal (-), for connecting welding and return cables. The output to which the welding cable

is connected depends on the welding method or type of electrode used.

Connect the return cable to the other output on the power source. Secure the return cable’s

contact clamp to the workpiece, and make sure that there is a good contact between the

workpiece and the output for the return cable on the power source.

5 OPERATION

0463 712 101

- 15 -

• For TIG welding, the negative welding terminal (-) is used for the welding torch and the

positive welding terminal (+) is used for the return cable.

• For MMA welding, the welding cable can be connected to the positive welding terminal

(+) or negative welding terminal (-), depending on the type of electrode used. The

connection polarity is stated on the electrode packaging.

5.4 Turning the power on/off

Turn on the power by turning the switch to the “ON” (I) position.

Turn the unit off by turning the switch to the “O” position.

Whether the power supply is interrupted or the power source is switched off in the normal

manner, weld programs are stored so that they are available the next time the unit is started.

CAUTION!

Do not turn off the power source during welding (with load).

5.5 Fan control

The ET 200iP PRO is fitted with a fan as needed feature. Fan as needed automatically

switches the cooling fan off when it is not required. This has two main advantages; (1) to

minimize power consumption, and (2) to minimize the amount of contaminants such as dust

that are drawn into the power source.

Note that the fan will only operate when required for cooling purposes and will automatically

switch off when not required.

5.6 Thermal protection

The power source includes thermal protection against overheating. When

overheating occurs the welding is stopped and overheating indicator on the

panel will be lit and an error message shows in the display. The protection is

automatically reset when the temperature has been sufficiently reduced.

5.7 Functions and symbols

MMA welding

MMA welding may also be referred to as welding with coated electrodes. Striking

the arc melts the electrode, and its coating forms protective slag.

For MMA welding the power source shall be supplemented with:

• welding cable with electrode holder

• return cable with clamp

Arc force

The arc force function determines how the current changes in response to

variations in arc length during welding. Use a low value of arc force to get a calm

arc with little spatter and use a high value to get a hot and digging arc.

Arc force only applies to MMA welding.

5 OPERATION

0463 712 101

- 16 -

Hot start

The hot start function temporarily increases the current in the beginning of the

weld. Use this function to reduce risk of insufficient fusion and electrode sticking

and scratching.

Hot start only applies to MMA welding.

TIG welding

TIG welding melts the metal of the workpiece, an arc initiated from a

non-consuming tungsten electrode. The weld pool and electrode are protected

by shielding gas.

For TIG welding, the welding power source shall be supplemented with:

• a TIG torch with gas valve

• an argon gas cylinder

• an argon gas regulator

• tungsten electrode

This power source performs Live TIG start (TIG Live).

The tungsten electrode is placed against the workpiece. When lifted away from

workpiece the arc is struck at a limited current level.

HF start

The HF (High Frequency) start function strikes the arc by means of a spark from

the tungsten electrode to the workpiece as the electrode is brought closer to the

workpiece and the trigger on the TIG torch is pressed.

Voltage Reduction Device (VRD)

The VRD function ensures that the open-circuit voltage does not exceed 35V

when welding is not being carried out. This is indicated by a lit VRD indicator on

the panel. Contact an authorised ESAB service technician to activate this

function.

5 OPERATION

0463 712 101

- 17 -

5.8 Setting panel

1. Overheating indicator 7. Options button

2. Display 8. Welding current control knob and

advanced feature control knob

3. VRD function (reduced open-circuit

voltage) indicator

9. Process selection button

4. Trigger mode indicator 10. MMA indicator

5. Pulse mode indicator 11. TIG Live indicator

6. Frequency indicator 12. TIG HF indicator

Process selection button (9):

• TIG HF (12)

• TIG Live (11)

• MMA (10)

• Navigation

• Parameter selection

Press the Process selection button (9) for 3 sec to go to the advanced feature menu and

press Process selection button (9) to select the values. Use the Welding current control

knob(8) to change the values.

In TIG HF or TIG Live mode:

• Gas pre flow time (PREG 0 - 5s)

• Start current (IGNA 10 - 100%)

• Up slope time (SLPU 0 - 10s)

• Down slope time (SLPD 0 - 10s)

• End current (FINA 10 - 100%)

• Gas post flow time (POSG 0.5 - 15s)

• Background current (BKGA 10 - 100%)

In MMA mode:

5 OPERATION

0463 712 101

- 18 -

• Hot start (HOTS -10 - +10)

• Arc force (ARCF -10 - +10)

• Cellulose electrode (CELL On / Off)

Press the Options button (7) to set the following:

• Trigger mode (4): 2 stroke / 4 stroke

• Pulse mode (5): (On / Off)

• Frequency (6): (0.2 - 500Hz) – only if Pulse mode is ON.

5.9 Remote control

Connect the remote control to the front of the power source. When the remote control is

connected, it is automatically activated. The maximum setting of the power source will be

determined by the respective front panel control, irrespective of the remote control device

setting.

6 MAINTENANCE

0463 712 101

- 19 -

6 MAINTENANCE

WARNING!

The mains supply must be disconnected during cleaning and maintenance.

CAUTION!

Only persons with the appropriate electrical knowledge (authorised personnel) may

remove the safety plates.

CAUTION!

The product is covered by manufacturer's warranty. Any attempt to carry out repair

work by non-authorised service centers or personnel will invalidate the warranty.

NOTE!

Regular maintenance is important for safe and reliable operation.

NOTE!

Perform maintenance more often during severe dusty conditions.

Before each use - make sure that:

• Product and cables are not damaged,

• The torch is clean and not damaged.

6.1 Routine maintenance

Maintenance schedule during normal conditions. Check equipment prior to every use.

Interval Area to maintain

Every 3 months

Clean or replace

unreadable labels.

Clean weld terminals. Check or replace weld

cables.

Every 6 months

Clean inside

equipment. Use dry

compressed air with

reduced pressure.

6.2 Cleaning instruction

To maintain the performance and increase the lifetime of the power source it is mandatory to

clean it regularly. How often depends on:

6 MAINTENANCE

0463 712 101

- 20 -

• the welding process

• the arc time

• the working environment

CAUTION!

Make sure that the cleaning procedure is done in a suitable prepared workspace.

CAUTION!

During cleaning, always wear recommended personal safety equipment, such as

ear plugs, safety glasses, masks, gloves and safety shoes.

1. Disconnect the power source from the mains supply.

2. Open the enclosure and use a vacuum cleaner to remove any accumulated dirt, metal

filings, slag and loose material. Keep the shunt and lead screw surfaces clean as

accumulated foreign material may reduce the welders output welding current.

Page is loading ...

ESAB Rogue ET 200iP PRO User manual

Brand: ESAB

Model: Rogue ET 200iP PRO

Category: Welding System

Type: User manual

Download PDF

report

ESAB Rogue ET 200iP PRO User manual

ESAB Rogue ET 200iP PRO User manual

Related papers

Other documents