Duerkopp Adler 867-M PREMIUM User manual

867-M PREMIUM
Brand
Duerkopp Adler
Model
867-M PREMIUM
Type
User manual

This manual is also suitable for

Duerkopp Adler 867-M PREMIUM is a sewing machine equipped with a handwheel cover interrogator that enhances safety by automatically switching off the sewing motor when the handwheel cover is opened during sewing, preventing potential injuries. Installation involves assembling the handwheel cover, connecting the PCB and cable, setting the DIB switch, and securing the cover with bolts and screws. It offers various benefits, including improved operator safety, reduced risk of accidents, and increased productivity.

Duerkopp Adler 867-M PREMIUM is a sewing machine equipped with a handwheel cover interrogator that enhances safety by automatically switching off the sewing motor when the handwheel cover is opened during sewing, preventing potential injuries. Installation involves assembling the handwheel cover, connecting the PCB and cable, setting the DIB switch, and securing the cover with bolts and screws. It offers various benefits, including improved operator safety, reduced risk of accidents, and increased productivity.

M-TYPE PREMIUM
Additional Instructions
Handwheel cover interrogator
All rights reserved.
Property of Dürkopp Adler GmbH and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler GmbH.
Copyright © Dürkopp Adler GmbH 2021
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Additional Instructions M-TYPE PREMIUM - 01.0 - 01/2021 1
1 General information ...................................................................3
2 Assembling the handwheel cover.............................................4
Table of Contents
2 Additional Instructions M-TYPE PREMIUM - 01.0 - 01/2021
General information
Additional Instructions M-TYPE PREMIUM - 01.0 - 01/2021 3
1 General information
Components of the kit M-TYPE PREMIUM
Check whether the scope of delivery for kit 0867 100834 is correct prior
to installation.
Part number Quantity Description
0867 100770 1 Handwheel guard
0815 710200 1 Inductive transmitter
9825 350305 1 Plug housing
0867 100780 1 Carrier
9202 100535 2 Countersunk screw
9203 001897 2 Cylinder-head bolt
9330 400017 1 Washer
9204 001257 1 Countersunk screw
0867 100820 1 Bolt
0867 100790 1 Bolt
9401 000039 1 Magnet
9301 101961 1 Cylinder pin
9330 000087 1 Washer
Assembling the handwheel cover
4 Additional Instructions M-TYPE PREMIUM - 01.0 - 01/2021
2 Assembling the handwheel cover
Fig. 1: Assembling the handwheel cover (1)
To assemble the handwheel cover:
1. Disassemble the handwheel.
2. Disassemble the motor cover.
3. If not yet present, assemble PCB (1).
4. Connect PCB (1) with the cable (2) to PCB (3).
• Slot PCB (1): X6 (IN)
• Slot PCB (3): X29
WARNING
Risk of injury from moving parts!
Crushing possible.
Switch off the machine before assembling the
handwheel cover.
(1) - PCB
(2) - Cable
(3) - PCB
①
②
③
Assembling the handwheel cover
Additional Instructions M-TYPE PREMIUM - 01.0 - 01/2021 5
Fig. 2: Assembling the handwheel cover (2)
5. Feed the cable (5) of the handwheel cover (4) from the outside
through a ventilation slot on the side of the motor cover.
6. Connect the plug (8) with the cable (5).
• brown core: Slot 1
• blue core: Slot 2
• black core: Slot 3
Information
The coding lugs (7) of the respective contact must point to the lever (9) on
the plug (8).
Insert each contact into the plug (8) until it snaps into place with a click.
Slot 1 is marked with a line on the back of the plug (8).
7. Insert the cable (8) at an available slot on the PCB (1).
Possible slots are X2, X3, X4 or X5.
8. Set the DIB switch (6) of the corresponding slot to OFF.
The operation lock is activated.
If the handwheel cover is opened during sewing, the sewing motor
will be switched off.
(4) - Handwheel cover
(5) - Cable
(6) - DIB switch
(7) - Coding lugs
(8) - Plug
(9) - Lever
④⑥⑧⑤ ⑦⑨
Assembling the handwheel cover
6 Additional Instructions M-TYPE PREMIUM - 01.0 - 01/2021
Fig. 3: Assembling the handwheel cover (3)
9. Assemble the motor cover.
10. Screw the long bolt (10) and the short bolt (11) instead of the screw
into the motor cover.
11. Tighten the ring (12) of the handwheel cover (4) with the screw (13)
at bolts (10) and (11).
(4) - Handwheel cover
(10) - Bolt
(11) - Bolt
(12) - Ring
(13) - Screws
⑩⑫⑬
⑪⑫④ ⑬
Assembling the handwheel cover
Additional Instructions M-TYPE PREMIUM - 01.0 - 01/2021 7
Fig. 4: Assembling the handwheel cover (4)
12. Assemble the handwheel.
13. Close the handwheel cover (4).
(4) - Handwheel cover
④
Assembling the handwheel cover
8 Additional Instructions M-TYPE PREMIUM - 01.0 - 01/2021
DÜRKOPP ADLER GmbH
Potsdamer Str. 190
33719 Bielefeld
Germany
Phone: +49 (0) 521 925 00
Email: [email protected]m
www.duerkopp-adler.com
Subject to design changes - Part of the machines shown with additional equipment - Printed in Germany
© Dürkopp Adler GmbH - Additional Instructions - 0791 867705 EN - 01.0 - 01/2021
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Duerkopp Adler 867-M PREMIUM User manual

867-M PREMIUM
Brand
Duerkopp Adler
Model
867-M PREMIUM
Type
User manual
This manual is also suitable for

Duerkopp Adler 867-M PREMIUM is a sewing machine equipped with a handwheel cover interrogator that enhances safety by automatically switching off the sewing motor when the handwheel cover is opened during sewing, preventing potential injuries. Installation involves assembling the handwheel cover, connecting the PCB and cable, setting the DIB switch, and securing the cover with bolts and screws. It offers various benefits, including improved operator safety, reduced risk of accidents, and increased productivity.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents