Develop PC-208 Installation guide

Brand: Develop

Model: PC-208

Type: Installation guide

Develop PC-208 is a paper feed cabinet that can be used with various printing machines. It has a capacity of up to 2,000 sheets of paper and can accommodate paper sizes from A4 to A3. The cabinet is equipped with a number of features that make it easy to use, including a self-adjusting paper feed system, a paper level indicator, and a paper jam detection system. The cabinet also comes with a number of accessories, such as a paper tray and a dust cover.

E-1

INSTALLATION MANUAL

A1V4-9582-00

PC-208 Paper Feed Cabinet

Caution:

Lifting the machine in an awkward position or

transporting it in a poorly balanced position could

result in personal injury. When transporting the

machine, assign an adequate number of persons

to the job and ensure that each person can take a

good position of not being excessively loaded.

(mass: approx. 33 kg (72-3/4 lb))

I. Accessory parts

Note:

This manual provides the illustrations of the acces-

sory parts and machine that may be slightly differ-

ent in shape from yours. In that case, instead of

the illustrations, use the appearance of your

machine to follow the installation procedure. This

does not cause any significant change or problem

with the procedure.

No. Name Shape Q’ty

1. Fixing leg

2. Fixing leg

cover A

3. Fixing leg

cover B

4. Fixing

bracket A

5. Fixing

bracket B

6. Fixing

bracket C

7. Screw

(4 × 8 mm)

A1V4IXC068DA

4348U099MB

A1V4IXC001DA

4658U021AA

A1V4IXC002DA

A1V4IXC003DA

4038IXC033DA

8. Paper size

label

set

9. Installation

manual

set

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting the head in the plastic bag

involves danger of suffocation.

No. Name Shape Q’ty

4980IXC019MA

Note:

• The three supplied fixing legs are being packed

under the cushioning material. Turn the cush-

ioning material upside down to remove the fix-

ing legs.

• When removing the paper feed cabinet from its

shipping carton, do not hold the reinforcement

bracket (as a personal injury or a deformed

frame could result).

• When removing the paper feed cabinet from the

carton or carrying it, be sure to hold it by the

locations shown in the illustration.

II. Installation procedures

1. Turn off the machine and unplug the power cord

from the power outlet.

2. Remove the protective tape from the paper feed

cabinet.

Note:

Do not peel the tape that fixes the paper feed cab-

inet hookup harness in position until the machine

is attached to the paper feed cabinet.

A1V4IXC079DA

A1V4IXC004DA

Reinforcement bracket

A1V4IXC005DA

A1V4IXE061DA

Hookup

harness

A1V4IXC008DA

A1V4IXC007DA

Applied Machines: 423/363/283/223

MFP: 42 ppm/36 ppm/28 ppm/22 ppm

Product Code: A1UD/A1UE/A1UF/A1UG

E-2

3. Hold onto the portions indicated in the illustration,

place the machine onto the paper feed cabinet.

When placing the machine, use the positioning

pins in the rear of the paper feed cabinet to align

the machine correctly with the cabinet.

Note:

• When transporting or moving the machines,

assign adequate number of persons.

• When attaching the machine, as the reference

fit the machine with the corner A and B of the

paper feed cabinet.

4. Remove the cover from the back of the machine

as shown in the illustration. (One screw)

5. Peel the tape that fixes the paper feed cabinet

hookup harness in position.

6. Connect the two connectors of the paper feed

cabinet hookup harness to the machine.

7. Reinstall the cover which has been removed in

step 4. (One screw)

A1UDIXC003DA

A1V4IXC010DA

A1V4IXE062DA

A1V4IXE063DA

A1V4IXE064DA

A1V4IXE065DA

8. Secure the paper feed cabinet to the machine by

the two supplied fixing bracket A’s.

(Two supplied screws)

9. Slide out the second and third drawers from the

paper feed cabinet.

10. Perform the following steps (1) to (4) to screw

the machine and the paper feed cabinet

together.

(1) Insert the screw into the upper hole on the

machine and temporarily tighten the screw.

(One supplied screw)

(2) Hang the supplied fixing bracket B on the

screw indicated in step (1).

(3) Align the hole of the paper feed cabinet and

the lower hole of the fixing bracket B. Insert the

screw into the holes and tighten the screw.

(One supplied screw)

(4) Completely tighten the screw indicated in step

(1).

11. Install the supplied fixing bracket C (Right) to

secure the machine and the paper feed cabinet

together. (One supplied screw)

Note:

Be careful not to damage the sheets of mylar.

12. Slide the drawers back in.

A1V4IXC014DA

A1V4IXC057DA

A1V4IXC015DA

(1)

A1V4IXC016DA

(1)

A1V4IXC017DA

A1V4IXC018DA

Mylar

E-3

13. Move the machine and paper feed cabinet to the

installation site. Then, adjust the two adjusters

on the front side and the adjuster on the left rear

side to let the paper feed cabinet sit on the floor.

14. Install the supplied fixing legs (two pieces) at two

locations in the front shown in the illustration.

Tighten the screw into the hole A’s to install the

fixing leg. (Eight supplied screws)

Note:

• If you install the finisher (FS-527) immediately

after the installation of the paper feed cabinet,

do not install the fixing leg or fixing leg cover A

at the left front side.

• If the screw cannot be tightened into the hole

A’s because the machine is installed on cush-

ioned floor such as a carpet, use the hole B’s.

15. Install the supplied fixing leg cover A’s (two

pieces), following the steps below.

(1) While slightly pushing the left end of the fixing

leg cover A outward to get it stretched, put the

fixing leg cover on the fixing leg.

Note:

Make sure that the protruded portion shown in the

illustration is outside the fixing leg plate.

(2) Push the fixing leg cover A in the direction of

the arrow to install it.

Note:

Make sure that the tab of the protruded portion is

completely inserted into the hole (C).

To reduce the risk of injury due to unsta-

ble equipment, set stabilizers before use.

A1V4IXC019DA

A1V4IXC020DA

➁

➀

➁

➂

➃

A1V4IXC021DB

Protrusion

A1V4IXC080DA

Protrusion

16. Install the fixing leg at the right rear corner of the

machine. Tighten the screw into the hole A’s to

install the fixing leg. (Four supplied screws)

Note:

If the screw cannot be tightened into the hole A’s

because the machine is installed on cushioned

floor such as a carpet, use the hole B’s.

17. Install the fixing leg cover A (right rear), following

the steps below.

(1) While slightly pushing the left end of the fixing

leg cover A outward to get it stretched, put the

fixing leg cover on the fixing leg.

Note:

Make sure that the protruded portion shown in the

illustration is outside the fixing leg plate.

(2) Push the fixing leg cover A in the direction of

the arrow to install it.

Note:

Make sure that the tab of the protruded portion is

completely inserted into the hole (C).

To reduce the risk of injury due to unsta-

ble equipment, set stabilizers before use.

A1V4IXC022DA

➁

➀

➂

➃

A1V4IXC023DB

Protrusion

A1V4IXC081DA

Protrusion

E-4

18. Install the supplied fixing leg cover B (left rear).

(Two supplied screws)

19. Plug the power cord into the power outlet.

III. Loading paper

1. Slide out the third and fourth drawers.

2. Load the paper stack so that it rests below the tab

fitted to the edge guide.

Note:

• Make sure that the top level of the paper stack

does not exceed the ▼ (MAX) paper level indi-

cator.

• Slide the edge guide tightly up against the edge

of the paper stack so that there is no gap

between them.

• With the trailing edge stop, fit its locking tab

properly into the slit at the correct paper size

position.

• Correct any curl in the paper before loading.

3. Slide the drawers back in.

IV. Affixing the paper size label

Affix the paper size label to the location shown in the

illustration.

(The size label is similarly put on the fourth.)

V. Checking and Adjusting the Paper

Reference Position

1. Turn on the machine’s sub and main power

switches.

2. Display the Service Mode screen (For details of

how to display the Service Mode screen, see the

Service Manual).

3. Touch “Machine.”

4. Touch “Printer Area.”

5. Touch “Centering.”

6. Touch “3rd.” and then press the Start key.

A test print will be produced.

7. Measure width A from the edge of the paper to

the pattern printed on the test print and check that

it falls within the specified range.

Specifications: 3.0 mm ± 1.0 mm

• Adjusting the paper reference position

If the measured width A falls outside the specified

range, enter the correction value using the or

key.

8. Produce another test print and check to see if

width A falls within the specified range.

* If the use of the or key does not allow

the measurement to fall within the specified

range, perform the following steps.

A1V4IXC024DA

A0XWMXC015MB

A0XWMXC016MB

A1V4IXC078DA

4061IXC147DA

Paper exit

direction

9. Slide out the drawer and unload paper from it.

10. Loosen the three screws shown in the illustra-

tion.

11. Watching the graduations provided in the

drawer, move the edge guide in the rear.

• If width A is greater than the specified value,

move the edge guide toward the front.

• If width A is smaller than the specified value,

move the edge guide toward the rear.

12. Load paper and let the machine produce

another test print. Then, check width A.

* Make the adjustment until width A falls within the

specified range.

13. Tighten the screws which has been loosened in

step 10.

14. Perform the same check and adjustment proce-

dures for the fourth drawer.

1. Touch “Centering (Duplex 2nd side).”

2. Touch “3rd.” and then press the Start key.

A test print will then be produced.

3. Measure width A of the test pattern on the back-

side of the test print produced and check that it

falls within the specified range.

Specifications: 3.0 mm ± 2.0 mm

• Adjusting the paper reference position

If the measured width A falls outside the specified

range, enter the correction value using the or

key.

4. Produce another test print and check to see if

width A falls within the specified range.

5. Perform the same check and adjustment proce-

dures for the fourth drawer.

6. Touch “END.”

7. Touch “Exit” on the Service Mode screen.

8. Turn OFF and ON the Main Power Switch.

Note:

When displayed the Service Mode screen, be sure

to turn off the main power after exiting the Service

Mode screen and wait for 10 seconds or more

before turning on.

A0XWMXC018MB

A0XWMXC019MA

4061IXC152DA

Paper exit

direction

Develop PC-208 Installation guide

Develop PC-208 Installation guide

Develop PC-208 Installation guide

Related papers

Other documents