Makita BDF343 Owner's manual

GB Cordless Driver Drill Instruction manual

F Perceuse-visseuse sans fil Manuel d’instructions

D Akku-Bohrschrauber Betriebsanleitung

I Trapano avvitatore a batteria Istruzioni per l’uso

NL Accuschroefboormachine Gebruiksaanwijzing

E Taladro sin cables Manual de instrucciones

P Berbequim sem fios Manual de instruções

DK Akku bore-skruemaskine Brugsanvisning

GR ∆ραπανκατσάιδ µπαταρίας δηγίες ρήσης

BDF343

BDF453

Page is loading ...

3

ENGLISH

Explanation of general view

SPECIFICATIONS

• Due to our continuing programme of research and development, the specifications herein are subject to change without

notice.

• Note: Specifications may differ from country to country.

Symbols

END004-2

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

............. Read instruction manual.

Intended use

ENE034-1

The tool is intended for drilling and screw driving in wood,

metal and plastic.

SPECIFIC SAFETY RULES GEB002-2

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to drill

safety rules. If you use this power tool unsafely or

incorrectly, you can suffer serious personal injury.

1. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high

locations.

3. Hold the tool firmly.

4. Keep hands away from rotating parts.

5. Do not leave the tool running. Operate the tool

only when hand-held.

6. Do not touch the drill bit or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

7. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

IMPORTANT SAFETY

INSTRUCTIONS ENC007-2

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain. A battery short can cause a large current

flow, overheating, possible burns and even a

breakdown.

1. Red part

2. Button

3. Battery cartridge

4. Switch trigger

5. Reversing switch lever

6. Speed change lever

7. Adjusting ring

8. Graduation

9. Pointer

10. Sleeve

Model BDF343 BDF453

Capacities

Steel 10 mm 13 mm

Wood 25 mm 36 mm

Wood screw 5.1 mm x 63 mm 6 mm x 75 mm

Machine screw 6 mm

No load speed (min

-1

)

High (2) 0 - 1,300

Low (1) 0 - 400

Overall length 192 mm 214 mm

Net weight 1.3 kg (BL1415)/1.5 Kg (BL1430) 1.6 kg (BL1815)/1.8 Kg (BL1830)

Rated voltage D.C. 14.4 V D.C. 18 V

4

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice less

tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

(Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Switch action (Fig. 2)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Reversing switch action (Fig. 3)

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

Speed change (Fig. 4)

To change the speed, first switch off the tool and then

slide the speed change lever to the “2” side for high speed

or, “1” side for low speed. Be sure that the speed change

lever is set to the correct position before operation. Use

the right speed for your job.

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the “1” side and “2”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

Adjusting the fastening torque (Fig. 5)

The fastening torque can be adjusted in 17 steps by

turning the adjusting ring so that its graduations are

aligned with the pointer on the tool body. The fastening

torque is minimum when the number 1 is aligned with the

pointer, and maximum when the marking is aligned with

the pointer.

The clutch will slip at various torque levels when set at the

number 1 to 16. The clutch is designed not to slip at

the marking.

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing driver bit or drill bit

(Fig. 6)

Turn the sleeve counterclockwise to open the chuck jaws.

Place the bit in the chuck as far as it will go. Turn the

sleeve clockwise to tighten the chuck.

To remove the bit, turn the sleeve counterclockwise.

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it

fully until the red part cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

5

Screwdriving operation (Fig. 7)

CAUTION:

• Adjust the adjusting ring to the proper torque level for

your work.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

CAUTION:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

NOTE:

• When driving wood screws, predrill pilot holes to make

driving easier and to prevent splitting of the workpiece.

See the chart.

Drilling operation

First, turn the adjusting ring so that the pointer points to

the marking. Then proceed as follows.

Drilling in wood

When drilling in wood, the best results are obtained with

wood drills equipped with a guide screw. The guide screw

makes drilling easier by pulling the bit into the workpiece.

Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a center-punch and hammer at

the point to be drilled. Place the point of the bit in the

indentation and start drilling. Use a cutting lubricant when

drilling metals. The exceptions are iron and brass which

should be drilled dry.

CAUTION:

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool

performance and shorten the service life of the tool.

• There is a tremendous force exerted on the tool/bit at

the time of hole break through. Hold the tool firmly and

exert care when the bit begins to break through the

workpiece.

• A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the tool may back out abruptly if you do

not hold it firmly.

• Always secure small workpieces in a vise or similar

hold-down device.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Drill bits

• Screw bits

• Various type of Makita genuine batteries and chargers

• Automatic refreshing adapter

• Plastic carrying case

For Model BDF343

For European countries only

Noise

ENG103-1

The typical A-weighted noise level determined according

to EN60745-2-1:

Sound pressure level (L

pA

): 70 dB (A) or less

The noise level under working may exceed 85 dB (A).

Wear ear protection

Vibration

ENG202-1

The vibration total value (tri-axial vector sum) determined

according to EN60745-2-1:

Work mode: drilling into metal

Vibration emission (a

h,D

): 2.5 m/s

2

or less

For Model BDF453

For European countries only

Noise

ENG101-1

The typical A-weighted noise level determined according

to EN60745-2-1:

Sound pressure level (L

pA

): 72 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 85 dB (A).

Wear ear protection

Vibration

ENG202-1

The vibration total value (tri-axial vector sum) determined

according to EN60745-2-1:

Work mode: drilling into metal

Vibration emission (a

h,D

): 2.5 m/s

2

or less

Nominal diameter of wood

screw (mm)

Recommended size of pilot

hole (mm)

3.1 2.0 - 2.2

3.5 2.2 - 2.5

3.8 2.5 - 2.8

4.5 2.9 - 3.2

4.8 3.1 - 3.4

5.1 3.3 - 3.6

5.5 3.7 - 3.9

5.8 4.0 - 4.2

6.1 4.2 - 4.4

6

EC-DECLARATION OF CONFORMITY ENH102-7

Model; BDF343, BDF453

We declare under our sole responsibility that this product

is in compliance with the following standards of

standardized documents;

EN60745, EN55014 in accordance with Council

Directives, 2004/108/EC, 98/37/EC.

CE 2007

Tomoyasu Kato

Director

Responsible Manufacturer:

Makita Corporation

3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN

Authorized Representative in Europe:

Makita International Europe Ltd.

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15

8JD, ENGLAND

Page is loading ...

Makita Corporation

Anjo, Aichi, Japan

884821-993

Makita BDF343 Owner's manual

Makita BDF343 Owner's manual

in other languages

Related papers

Other documents